Juniper Networks 200 manual Copyright Notice

Page 2

Copyright Notice

Copyright © 2007 Juniper Networks, Inc. All rights reserved.

Juniper Networks, the Juniper Networks logo, NetScreen, NetScreen Technologies, GigaScreen, and the NetScreen logo are registered trademarks of Juniper Networks, Inc. NetScreen-5GT, NetScreen-5XP, NetScreen-5XT, NetScreen-25, NetScreen-50, NetScreen-100, NetScreen-204, NetScreen-208, NetScreen-500, NetScreen-5200, NetScreen-5400, NetScreen-Global PRO, NetScreen-Global PRO Express, NetScreen-Remote Security Client, NetScreen-Remote VPN Client, NetScreen-IDP 10, NetScreen-IDP 100, NetScreen-IDP 500, GigaScreen ASIC, GigaScreen-II ASIC, and NetScreen ScreenOS are trademarks of Juniper Networks, Inc. All other trademarks and registered trademarks are the property of their respective companies.

Information in this document is subject to change without notice.

No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without receiving written permission from:

Juniper Networks, Inc.

ATTN: General Counsel

1194 N. Mathilda Ave. Sunnyvale, CA 94089-1206

FCC Statement

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. The equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with NetScreen’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Consult the dealer or an experienced radio/TV technician for help.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Caution: Changes or modifications to this product could void the user's warranty and authority to operate this device.

Disclaimer

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR JUNIPER NETWORKS REPRESENTATIVE FOR A COPY.

Image 2
Contents NETSCREEN-200 Series Copyright Notice Contents IX-I Preface Guide OrganizationCommand Line Interface CLI Conventions Juniper Networks Netscreen PublicationsOverview1 NETSCREEN-200 Systems NetScreen-204 DeviceNetScreen-208 Device System Status LED Display Front PanelAsset Recovery Pinhole RedConsole and Modem Ports Compact Flash Card SlotRear Panel Power SuppliesEthernet Interfaces Power Fuse Overview User’s Guide Installing the Device Performing EQUIPMENT-RACK Installation Equipment Rack Installation GuidelinesGeneral Installation Guidelines Mid-Mount Connecting the PowerFront Mount Wiring a DC Power Supply Connecting the NETSCREEN-200 Device to Other Devices Installing the Device User’s Guide Configuring the Device Operational Modes Transparent ModeRoute Mode NETSCREEN-200 Series Device Interfaces Ethernet1 through ethernet8Connecting the Device AS a Single Security Gateway Connectivity ExamplesPerforming Device Connection Establishing AN HA Connection Between Devices DeviceDevice Performing Initial Connection and Configuration Establishing a Terminal Emulator ConnectionChanging Your Admin Name and Password Setting Port and Interface IP AddressesSetting the IP Address of the Management Interface Starting a Console Session Using Telnet Configuring the Device for Telnet and Webui SessionsStarting a Console Session Using Dialup Establishing a GUI Management SessionNetScreen WebUI application window appears Using CLI Commands to Reset the Device Asset RecoveryUsing the Asset Recovery Pinhole to Reset the Device Configuring the Device User’s Guide Specifications NETSCREEN-200 Attributes Electrical SpecificationSafety Certifications EnvironmentalIndex IX-II