GarrettCom MAGNUM 6KM manual 6KM4-4M12, 4 x 10/100Mb M12 Slot C

Page 33

Magnum 6KM Mobile Ethernet Switch Installation and User Guide

07/10

5.1.2

6KM4-4M12, 4 x 10/100Mb M12 (Slot C)

 

The 6KM4-4M12 4-port Copper module provides four 10/100Mb switched M12 ports. The 10/100Mb switched ports normally (as a default setting) are independently N-way auto-negotiating and auto-crossover (MDIX) for operation at 10 or 100Mb speed in full- or half-duplex mode. (i.e., each independently selects a mode and speed to match the device at the other end of the twisted pair cable).

(for auto-negotiation and MDIX details, see Section 4.2 in this 6KM User Guide). On the model 6KM4-4M12 module, there is one LED for each port. The

Link/A LED indicates Link “ready for operation” for that port when lit. The A (Activity) LED indicates receiving Activity on that port when blinking. A twisted pair cable must be connected into an M12 port and the Link indicator for that port must be ON (indicating there is a powered-up device at the other end of the cable) in order for a Link LED to provide valid indications of operating conditions on that port.

Using the 6K (MNS-6K or MNS-6K-SECURE) management software, the user may disable auto-negotiation and fix the desired operation of each M12 port. The user may select 10Mb or 100Mb speed and full- or half-duplex mode per-port as per user requirements. (See Magnum MNS-6K Software Manual for additional info)

NOTE: for Power Substations: In support of the IEEE 1613 Class 2 standard, GCI advises that, for substation applications, the M12 ports are intended for connectivity to other communication equipment such as routers or telecommunication multiplexers installed in close proximity (i.e., less than 2 meters or 6.5ft) to the 6KM. It is not recommended to use these ports in substation applications to interface to field devices across distances which could produce high (greater than 2500V ) levels of ground potential rise (GPR) during line-to-ground fault conditions. The 6KM passes the 1613specifications for zero packet loss with fiber ports and with M12 ports used as indicated here.

www . GarrettCom . com

28

Image 33
Contents Mobile Ethernet Switch Contacting GarrettCom, Inc GarrettCom, IncCanadian Emissions Statement Electrical Safety requirementsSpecifications Troubleshooting Technical Specifications Performance SpecificationsNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment LengthsCopper 1000Mb connector types supported Copper 10/100Mb connector types supportedFiber Multi-mode connector types supported Fiber Single-mode connector types supportedPower Consumption Dual -Source DC Power Input OptionalManagement Console connector Ordering Information Configuration Options see following pagesOptions and Extras Inspecting the Package and Product IntroductionProduct Description Magnum 6KM Mobile Ethernet Switch Frame Buffering and Flow Control Packet Prioritization, 802.1p QOSManaged Network Software for Magnum 6KM Web-browser, at ftp//ftp.garrettcom.comFeatures and Benefits „ M12 Copper connections „ Managed switching for high performance Ethernet LANs„ Fiber Ports Built-In „ MNS-6K-SECURE optional, for extra security Installation Connecting Ethernet Media Connecting Twisted Pair for 10/100Mb CAT3, CAT5, UTP or STPMedia Ieee Standard Www . GarrettCom . com Connecting Fiber Optic Cable to LC ports DIN-Rail Mounting the Magnum 6KM Mounting Dimensions for 6KM with metal brackets00 x 9.58 inches 10.20 x 24.33 cm center-to-center Panel / Wall Mounting position Single DC power input Powering the Magnum DC 6KM Mobile Ethernet SwitchesDual-Source DC power input AC power input5a Alarm Contacts Connecting the Console Terminal to Magnum 6KM M12 6KM Console Port connector1 M12 Console Port pin assignments Operation Switching FunctionalityFiltering and Forwarding Address LearningAuto-CrossMDIX and Auto-negotiation, for M12 ports Flow-control, Ieee 802.3x standard Power Budget Calculations for 6KM Modules with Fiber Media Magnum 6KM Mobile Ethernet Switch Port Modules6KM Modules Blinking = Activity LED LC 100Mb Fiber port, 2 LED per portOn = Link established Blinking = Activity LED6KM4-4M12, 4 x 10/100Mb M12 Slot C PoE LEDs Summary 3 P6KM4-4M12, 4 x PoE M12 Slot C5 6KM4-4SLC, 6KM4-4SLCL, 4 x Singlemode LC Slot C 6KM4-4MLC, 4 x Multimode LC Slot C6KM-2GM12, 2 x Gigabit M12 Slot B 7 6KM-2GMLC, 2 x Gigabit Multimode LC Slot B8 6KM-2GSLC, 6KM-2GSLCL, 2 x Gigabit Singlemode LC Slot B Troubleshooting When Calling for AssistanceBefore Calling for Assistance No Problem Found Return Material Authorization RMA ProcedureShipping and Packaging Information Appendix a Warranty InformationFig B1.0a Location of chassis ground Power Consumption Standard 6KM male DC Power Input connector B3.0 6KM DC Single Source InstallationB5.0 Troubleshooting B4.0 UL Requirements for DC-powered unitsAppendix C DC Dual Source Power Input C5.0 6KM Dual Source Installation C4.0 Features and Benefits of the DUAL-SOURCE DesignC2.0 Magnum 6KM, with DC Dual-Source option C3.0 DUAL-SOURCE OPTION, Theory of OperationStandard 6KM Dual Source male DC Power Input connector C6.0 Ordering Information for Dual Source DC PowerExample Magnum 6KM-48VDC Dual-Src-48V Standard 6KM male AC Power Input connector