GarrettCom 6K16V manual Media, Connecting Twisted Pair CAT5E or better, Unshielded or Shielded

Page 27
Media

Magnum 6K16V Managed Fiber Switch

Installation and User Guide (06/04)

(9/125 microns for single-mode, 50/125 or 62.5/125 microns for multi-mode where xx/xx are the diameters of the core and the core plus the cladding respectively). Single-mode fiber allows full bandwidth at longer distances, and may be used to connect 10 Mb nodes up to 10 Km apart, or 18Km with the 6K-SSC.

The same procedures as for multi-mode fiber applies to single-mode fiber connectors. Follow the steps listed in Section 3.2.2 above.

3.2.4Connecting Twisted Pair (RJ-45,CAT3, CAT5, Unshielded or Shielded) The RJ-45 ports of the Magnum 6K16V can be connected to the following two

media types: 100BASE-TX and 10BASE-T. CAT 5 cables should be used when making 100BASE-TX connections. When the ports are used as 10BASE-T ports, CAT 3 may be used. In either case, the maximum distance for unshielded twisted pair cabling is 100 meters (328 ft).

Media

IEEE Standard

Connector

Twisted Pair (CAT 3, 4, 5)

10BASE-T

RJ-45

Twisted Pair (CAT 5)

100BASE-TX

RJ-45

NOTE : It is recommended that high quality CAT. 5 cables (which work for both 10 Mb

and 100Mb) be used whenever possible in order to provide flexibility in a mixed-speed network, since dual-speed ports are auto-sensing for either 10 and 100Mb/s.

The following procedure describes how to connect a 10BASE-T or 100BASE- TX twisted pair segment to the RJ-45 port. The procedure is the same for both unshielded and shielded twisted pair cables.

1.Using standard twisted pair media, insert either end of the cable with an RJ-45 plug into the RJ-45 connector of the port. Note that, even though the connector is shielded, either unshielded or shielded cables and wiring may be used.

2.Connect the other end of the cable to the corresponding device

3.Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established

3.2.5Connecting Twisted Pair (CAT5E or better, Unshielded or Shielded)

The RJ-45 Gigabit ports of the Magnum 6K16V can be connected to the media

types, 1000BASE-T or CAT 5E or better 100-ohm UTP or shielded twisted pair (STP) balanced cable. The CAT 5E or better 100-ohm UTP or shielded twisted pair (STP) balanced cable is recommended to use when making 1000BASE-TX connections. In either case, the max distance for unshielded twisted pair cabling is 100 meters (328 ft).

Media

IEEE Standard

Connector

Twisted Pair (CAT 5E)

1000BASE-T

RJ-45

NOTE : It is recommended that high quality CAT. 5E cables (which work for both 100

Mb and 1000Mb) be used whenever possible in order to provide flexibility in a mixed-speed network.

www . GarrettCom . com

20

Image 27
Contents Hardware www . GarrettCom . comManaged Fiber Switch Installation and User GuideMagnum 6K16V Managed Fiber Switch Hardware Installation and User GuideTrademarks Reorient or relocate the receiving antenna Contacting GarrettCom, IncFederal Communications Commission Radio Frequency Interference StatementOPERATION SPECIFICATIONSInstallation IntroductionAPPENDIX B Internal DC Power Supply Options 5.0 Introduction - Magnum 6K16V Managed Fiber Switch PMTROUBLESHOOTING APPENDIX A WARRANTY INFORMATIONPERSONAL SWITCHES, 10/100MB 6K-SERIES MANAGED FIBER SWITCHES, GIGABIT, 100 ANDQUAD-SERIES FIBER SWITCHES, 100 & 10MBPS, FIBER AND “OUTDOOR” ETHERNET SWITCH, FOR TEMPERATUREMODELS MEDIA CONVERTERS, 10MB AND 100MB SERIESBRIDGE PORT MODULES BPMS, 4 TYPES, FOR SEGMENT TRANSCEIVERS, 10MB SERIES MINI-TRANSCEIVERS AND COAXNetwork Standards and Compliance, hardware 1.0 SPECIFICATIONS 1.1 Technical SpecificationsFiber Multi-mode connector types supported PerformancePower Supply Internal Fiber Single-mode connector typesAlarm Relay Contacts Management Console connectorEmail sales@GarrettCom.com for details Per-port jumpers and switchesAgency Approvals NEBS Test Classification NEBS Compliant1.2 Ordering Information Magnum Managed Fiber Switch 16 ports maxConfiguration Options MODEL DESCRIPTIONfiber ports connector 2.0 Introduction 2.1 Inspecting the Package and Product 2.2 Product Description - Magnum 6K16V Managed Fiber Switch 6K8-MLC or -SLC below 100Mb, mode, and connector2.2.1 Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Fig.2.2.2 SFF Fiber Port Modules 6K8-MTRJ to the left and2.2.2 Eight-Port Copper Module, 6K8-RJ45 with 4@ MTRJ 100Mb mm SFF 4@ RJ-45 + 2@ 100Mb SCThe Magnum Combo six-port modules are also available1@ 1000Mb Fiber SC + 4@10/ 100Mb 2.2.4 Four-Port 10 Mb and 100Mb mm Fiber ST Modules2.2.6 Gigabit 1000Mbps port modules 1@ 1000Mb Fiber SC + 2@ 100Mb SC2.2.7 Frame Buffering and Flow Control 2.2.6 Packet Prioritization, 802.1p QOSftp//ftp.garrettcom.com 2.2.8 Managed Network Software MNS-6K for Magnum 6K16V„ Features Fiber-Built-In 2.3 Features and Benefits„ Managed switching for high performance Ethernet LANs „ Switching services includes 802.1p QoS packet prioritization2.4 Applications Example 1 Magnum 6K16V Switch for a Industrial applicationInternet Fig. 2.1- The Industrial factory floor application with Magnum 6K16VSNMP Monitor 3.0 Installation 3.1 Locating Magnum 6K16V Switches3.2 Connecting Ethernet Media IEEE Standard 3.2.1 Connecting Fiber Optic ST-type, “twist-lock”3.2.2 Connecting Fiber Optic SC-type, Snap-In 3.2.3 Connecting Single-Mode Fiber OpticMedia 3.2.5 Connecting Twisted Pair CAT5E or better, Unshielded or Shielded3.3 DIN-Rail Mounting 3.2.6 Connecting Gigabit Media Using GBICs3.3.1 Mounting Dimensions for 6K16V with metal brackets 3.4 Powering the Magnum 6K16V Managed Fiber Switch Relay Contacts 3.5 Alarm Contacts for monitoring internal power, and Software Trapsand will void the warranty 3.6 6K16V Port Module 6KPM Installation3.6.1 Preparation for Installing and Removing 6KPMs Be sure the power cord is unpluggedFigure 3.6.1b Magnum 6K16V, Top view without chassis cover Caution Be careful not to disturb the power supplyStep 2. Remove Chassis Cover Figure 3.6.1a Removing the Front panel from the unitFig 3.6.2a Granddaughter Board shown separately 3.6.2 Installing 6KPM Cards in the Magnum 6K16VStep 3. Remove front panel face plate retaining screws Figure 3.6.1c Top View - 6KPM retaining screws hold Face Plateversion for 4 copper 10/100 ports Fig. 3.6.2c Daughter Board, top view ofFigure 3.6.2f Securely latching up 6KPM Cards into a Magnum 6K16V Fig. 3.6.2g Top View 6KPM Module installed inside a 6K16VStep 3. Remove 6KPM Card Caution Be sure the power cord is unplugged3.6.3 Removing 6KPM Cards firmly. Figure 3.6.3a Top View - 6 retaining s crews shown by arrowsEnlarged view of Magnum 6K16V Console Port area 3.7 Connecting a Management Console Terminal to Magnum 6K16VDB-9 Console port connector 3.7.1 RS-232 DB-9 Console Com port Serial port pin assignmentsAddress Learning 4.1 Switching Functionality4.0 OPERATION Filtering and ForwardingSpeed LED, ON when the speed is 100Mbps , OFF when the 4.3 Up-link Manual Switches set as = , for RJ-45 port onlyPower LED, ON when external power is applied to the unit Full / Half duplex LED, ON when the port is running fullAuto-negotiation per-port for 802.3u-compliant switches occurs when 4.6 Power Budget Calculations for Magnum 6K16V PM’s with Fiber Media 4.5 Flow-control, IEEE 802.3x standardLXSC40 and the “Cable Loss” for 9/125 Single-mode is 0.2 dB/km LXSC70 Km, fdx Magnum 6K16V Managed Fiber SwitchInstallation and User Guide 06/04 6KP4V5.0 Introduction - Magnum 6K16V Managed Fiber Switch Port Modules 5.1 Inspecting the Package and Product5.2 6KPM Module Description 5.2.1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST “twist lock” Module connectors and configured ports are ST connectorsand configured as 10Mb Half-duplex by defaultRJMSC is also a Combo 6 Port mode SC-type connectors. Itmodule of the 6K16V Switch The Magnum 6KP6as 25+ Km see Power Budget, Section 6KP8-MTRJ “small-form-factor”5.2.5 6KP8-MTRJ, 8 @100Mb multi-mode FX , MTRJ Small-Form-factor The functionality of this 100BASE-FX multi-mode 4 port module isThe Magnum 6KP8-45MT MTRJ connectors give an advantage5.2.6 6KP8-45MT, 4@ 10/100Mbps RJ-45 and 4@100Mb multi-mode FX MTRJ Small-Form-Factor5.2.9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port connecting to a hub or another switch 5.2.11 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 6KP8VSingle-Mode Fiber port LC 5.2.12 6KM-BLNK 5.2.11a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector6.1 Before Calling for Assistance 6.0 TROUBLESHOOTING6.3 Return Material Authorization RMA Procedure 6.2 When Calling for AssistanceNo Problem Found GarrettCom, Inc 213 Hammond Ave Fremont, CA Attn. Customer Service6.4 Shipping and Packaging Information B2.0 -48VDC, 24VDC and 125VDC POWER, THEORY OF OPERATION B1.0 SPECIFICATIONS FOR MAGNUM 6K16V SWITCHES, DC POWERB4.0 6K16V’S -48V, 24, 125 OR 5VDC INSTALLATION B3.0 APPLICATIONS FOR DC POWERED ETHERNET SWITCHESB5.0 OPERATION B4.1 UL Requirements for DC-powered unitsB7.0 TROUBLESHOOTING hooked up at the lastPower Supply Internal, 24VDC Dual-Source, model # Dual-Src-24V Power Supply Internal, 125VDC Dual-Source, model # Dual-Src-125VC3.0 DUAL-SOURCE OPTION, THEORY OF OPERATION C5.0 INSTALLATION C4.0 FEATURES AND BENEFITS OF THE DUAL-SOURCE DESIGNC7.0 OPERATION C5.1 UL RequirementsC6.0 ORDERING INFORMATION Example Magnum 6K16VR-48VDC