Fortinet ORTIWIFI-60A /AM manual Typographic conventions, Addressipv4

Page 11


Introduction	About this document

Typographic conventions

FortiWiFi documentation uses the following typographical conventions:

Convention	Example

Keyboard input	In the Gateway Name field, type a name for the remote VPN
	peer or client (for example, Central_Office_1).
Code examples	config sys global
	set ips-open enable
	end
CLI command syntax	config firewall policy
	edit id_integer
	set http_retry_count <retry_integer>
	set natip <address_ipv4mask>
	end
Document names	FortiGate Administration Guide

Menu commands	Go to VPN > IPSEC > Phase 1 and select Create New.

Program output	Welcome!
Variables	<address_ipv4>

FortiWiFi-60A/AM FortiOS 3.0 MR4 Install Guide	11
01-30004-0283-20070215

Image 11

Contents Install G U I D E Regulatory compliance TrademarksContents Configuring the modem interface Configuring the FortiWiFiIndex Using a wireless networkFortiWiFi Firmware Page FortiWiFi-60A/AM About the FortiWiFi unitFortiClient Register your FortiWiFi unitFortiGuard Subscription Services Fortinet Family ProductsFortiBridge FortiMailFortiAnalyzer FortiReporterDocument conventions About this documentAddressipv4 Typographic conventionsFortinet documentation FortiGate Install GuideComments on Fortinet technical documentation Customer service and technical supportFortinet Knowledge Center Customer service and technical support Package Contents Installing the FortiWiFi unitMounting Powering on the FortiWiFi unitTo power on the FortiWiFi unit SpecificationsTo power off the FortiWiFi unit Connecting to the FortiWiFi unitPowering off the FortiWiFi unit Command line interfaceTo connect to the web-based manager Connecting to the web-based managerSystem Dashboard Connecting to the CLIBits per second 9600 Data bits Parity Quick installation using factory defaultsTo connect to the CLI WelcomeGo to System Network Options Quick installation using factory defaults Factory defaults Factory default NAT/Route mode network configuration Factory default Dhcp server configurationFactory default firewall configuration Factory default Transparent mode network configurationFactory default protection profiles To reset the default settings Go to System Status Restoring the default settingsRestoring the default settings using the web-based manager Restoring the default settings using the CLIRestoring the default settings NAT/Route mode Planning the FortiWiFi configurationExample NAT/Route mode network configuration NAT/Route mode with multiple external network connectionsExample NAT/Route multiple internet connection Transparent modePreparing to configure the FortiWiFi unit in NAT/Route mode NAT/Route mode installationPPPoE setting User name Password Dhcp or PPPoE configurationUsing the web-based manager NAT/Route mode settings Administrator Password InternalTo configure interfaces Go to System Network Interface Configuring basic settingsConfiguring the FortiWiFi unit to operate in NAT/Route mode Adding a default routeVerifying the web-based manager configuration Using the command line interfaceTo set the WAN1 interface to use DHCP, enter To add/change the administrator passwordTo configure interfaces ExampleGet system interface To configure DNS server settingsTo add a default route To set the WAN1 interface to use PPPoE, enterTo connect the FortiWiFi unit Connecting the FortiWiFi unit to the networksNAT/Route mode connections Configuring the networksDNS Settings Transparent mode installationPreparing to configure Transparent mode Transparent mode settings Administrator PasswordTo verify the DNS server settings To change to Transparent mode using the CLITo connect the FortiWiFi unit running in Transparent mode Reconnecting to the web-based managerConnecting the FortiWiFi unit to your network Set the date and time Next stepsUpdating antivirus and IPS signatures Every Scheduling antivirus and IPS updatesTo update IPS signatures using the CLI Updating the IPS signatures from the CLIWeekly To enable schedule updates from the CLIAdding an override server DailyConfig system autoupdate override set address Set status End To add an override server using the CLINext steps Configuring the modem interface To configure the FortiWiFi-60A using the CLI Selecting a modem modeRedundant mode configuration Stand alone mode configurationEnter the following to configure the dialup account Configuring modem settings To disconnect the modem Connecting and disconnecting the modem in Stand alone modeTo configure modem settings Go to System Network Modem To connect to a dial-up account Go to System Network ModemKeywords and variables Description Default Configuring the modem using the CLIPeermodem1 Dead gateway detection Adding a Ping ServerAdding firewall policies for modem connections FortiWiFi unit as an Access Point Setting up a wireless networkRadio Frequency interface Positioning an Access PointUsing multiple access points Wireless Equivalent Privacy WEP Wireless SecurityMAC address filtering Wi-Fi Protected Access WPAAdditional security measures To disable Ssid Go to System Wireless Settings FortiWiFi operation modesService Set Identifier Access Point modeChanging the operating mode Setting up the FortiWiFi unit as an Access PointClient mode Set the security options Set the Dhcp settingsTo set the data security Go to System Wireless Settings Configure the firewall policies Upgrading to a new firmware version Upgrading the firmware using the web-based managerTo upgrade the firmware using the web-based manager Execute restore image image.out Upgrading the firmware using the CLITo upgrade the firmware using the CLI Execute restore image Tftp namestr tftpipv4Reverting to a previous firmware version Execute update-nowTo revert to a previous firmware version using the CLI Reverting to a previous firmware version using the CLIExecute restore image Tftp image.out To install firmware from a system reboot Enter Local Address Press Any Key To Download Boot ImagePress any key to display configuration menu Enter Tftp Server AddressDo You Want To Save The Image? y/n Restoring the previous configurationSave as Default firmware/Run image without savingD/R FortiUSB keyTo restore configuration using the CLI Backup and Restore from the FortiUSB keyTo backup configuration using the CLI To configure the USB Auto-Install using the CLI Using the USB Auto-Install featureTo test a new firmware image Testing a new firmware image before installing itAdditional CLI Commands for the FortiUSB key Testing a new firmware image before installing it Type n FortiWiFi unit running v3.x Bios Testing a new firmware image before installing it Numerics Index01-30004-0283-20070215