Fortinet ORTIWIFI-60A /AM manual Index, Numerics

Page 79

Index

Index

Numerics

802.11 standard 58

A

access point 57

adding a default route 35, 37 auto-dial 52

C

certificate, security 18

CLI

additional commands for FortiUSB key 75 configuring NAT/Route mode 35 connecting 19

upgrading the firmware 66, 68 client mode 62

comments, documentation 13 configuring

redundant mode 50 standalone mode 50

connecting

to the CLI 19

to the web-based manager 18 customer service 13

D

dashboard, system 19 dead gateway detection 56 default

gateway 24 protection profiles 26 restoring settings 27

DHCP configuration 33 starting IP 24 wireless 63

dial now button 52 dial on demand 52 documentation

commenting on 13 Fortinet 12

F

factory defaults

DHCP server configuration 24 firewall configuration 25 NAT/Route mode config 24 protection profiles 26 Transparent mode config 25

firewall policies modem 56 wireless 64

firmware

backup and restore from FortiUSB key 73

installing 70

re-installing current version 70 restoring previous config 72 reverting to an older version 70 testing firmware image 75 upgrading to a new version 65 upgrading using the CLI 66, 68

upgrading using the web-base manager 65, 67 FortiGate documentation

commenting on 13 Fortinet customer service 13 Fortinet documentation 12 Fortinet Family Products 8

FortiBridge 9

FortiClient 8

FortiGuard 8 FortiLog 9 FortiMail 9 FortiManager 9 FortiReporter 9

Fortinet Knowledge Center 13 FortiUSB key

additional CLI commands 75 backup and restore 73 USB Auto-Install 74

frequency 58

H

hang up button 52 holddown timer 52

I

idle timeout 52

installing factory defaults 20 interference 58 introduction

Fortinet documentation 12

L

lease duration DHCP 24

LED descriptions 16

M

MAC address filtering 60 Message Integrity Code (MIC) 60 modem

adding firewall policies 56 configuring settings 51 mode 52

redundant mode 49 standalone mode 49, 50 status 52

mounting 16

FortiWiFi-60A/AM FortiOS 3.0 MR4 Install Guide	79
01-30004-0283-20070215

Image 79

Contents Install G U I D E Regulatory compliance TrademarksContents Configuring the modem interface Configuring the FortiWiFiFortiWiFi Firmware Using a wireless networkIndex Page FortiWiFi-60A/AM About the FortiWiFi unitFortiClient Register your FortiWiFi unitFortiGuard Subscription Services Fortinet Family ProductsFortiBridge FortiMailFortiAnalyzer FortiReporterDocument conventions About this documentAddressipv4 Typographic conventionsFortinet documentation FortiGate Install GuideFortinet Knowledge Center Customer service and technical supportComments on Fortinet technical documentation Customer service and technical support Package Contents Installing the FortiWiFi unitMounting Powering on the FortiWiFi unitTo power on the FortiWiFi unit SpecificationsTo power off the FortiWiFi unit Connecting to the FortiWiFi unitPowering off the FortiWiFi unit Command line interfaceTo connect to the web-based manager Connecting to the web-based managerSystem Dashboard Connecting to the CLIBits per second 9600 Data bits Parity Quick installation using factory defaultsTo connect to the CLI WelcomeGo to System Network Options Quick installation using factory defaults Factory defaults Factory default NAT/Route mode network configuration Factory default Dhcp server configurationFactory default firewall configuration Factory default Transparent mode network configurationFactory default protection profiles To reset the default settings Go to System Status Restoring the default settingsRestoring the default settings using the web-based manager Restoring the default settings using the CLIRestoring the default settings NAT/Route mode Planning the FortiWiFi configurationExample NAT/Route mode network configuration NAT/Route mode with multiple external network connectionsExample NAT/Route multiple internet connection Transparent modePreparing to configure the FortiWiFi unit in NAT/Route mode NAT/Route mode installationPPPoE setting User name Password Dhcp or PPPoE configurationUsing the web-based manager NAT/Route mode settings Administrator Password InternalTo configure interfaces Go to System Network Interface Configuring basic settingsConfiguring the FortiWiFi unit to operate in NAT/Route mode Adding a default routeVerifying the web-based manager configuration Using the command line interfaceTo set the WAN1 interface to use DHCP, enter To add/change the administrator passwordTo configure interfaces ExampleGet system interface To configure DNS server settingsTo add a default route To set the WAN1 interface to use PPPoE, enterTo connect the FortiWiFi unit Connecting the FortiWiFi unit to the networksNAT/Route mode connections Configuring the networksDNS Settings Transparent mode installationPreparing to configure Transparent mode Transparent mode settings Administrator PasswordTo verify the DNS server settings To change to Transparent mode using the CLIConnecting the FortiWiFi unit to your network Reconnecting to the web-based managerTo connect the FortiWiFi unit running in Transparent mode Set the date and time Next stepsUpdating antivirus and IPS signatures Every Scheduling antivirus and IPS updatesTo update IPS signatures using the CLI Updating the IPS signatures from the CLIWeekly To enable schedule updates from the CLIAdding an override server DailyConfig system autoupdate override set address Set status End To add an override server using the CLINext steps Configuring the modem interface To configure the FortiWiFi-60A using the CLI Selecting a modem modeRedundant mode configuration Stand alone mode configurationEnter the following to configure the dialup account Configuring modem settings To disconnect the modem Connecting and disconnecting the modem in Stand alone modeTo configure modem settings Go to System Network Modem To connect to a dial-up account Go to System Network ModemKeywords and variables Description Default Configuring the modem using the CLIPeermodem1 Adding firewall policies for modem connections Adding a Ping ServerDead gateway detection FortiWiFi unit as an Access Point Setting up a wireless networkUsing multiple access points Positioning an Access PointRadio Frequency interface Wireless Equivalent Privacy WEP Wireless SecurityAdditional security measures Wi-Fi Protected Access WPAMAC address filtering To disable Ssid Go to System Wireless Settings FortiWiFi operation modesService Set Identifier Access Point modeClient mode Setting up the FortiWiFi unit as an Access PointChanging the operating mode To set the data security Go to System Wireless Settings Set the Dhcp settingsSet the security options Configure the firewall policies To upgrade the firmware using the web-based manager Upgrading the firmware using the web-based managerUpgrading to a new firmware version Execute restore image image.out Upgrading the firmware using the CLITo upgrade the firmware using the CLI Execute restore image Tftp namestr tftpipv4Reverting to a previous firmware version Execute update-nowTo revert to a previous firmware version using the CLI Reverting to a previous firmware version using the CLIExecute restore image Tftp image.out To install firmware from a system reboot Enter Local Address Press Any Key To Download Boot ImagePress any key to display configuration menu Enter Tftp Server AddressDo You Want To Save The Image? y/n Restoring the previous configurationSave as Default firmware/Run image without savingD/R FortiUSB keyTo backup configuration using the CLI Backup and Restore from the FortiUSB keyTo restore configuration using the CLI To configure the USB Auto-Install using the CLI Using the USB Auto-Install featureAdditional CLI Commands for the FortiUSB key Testing a new firmware image before installing itTo test a new firmware image Testing a new firmware image before installing it Type n FortiWiFi unit running v3.x Bios Testing a new firmware image before installing it Numerics Index01-30004-0283-20070215