Fortinet ORTIWIFI-60A /AM manual Contents

Page 3

Contents

Contents
Contents	3
Introduction	7
About the FortiWiFi unit	7
FortiWiFi-60A/AM	7
Register your FortiWiFi unit	8
Fortinet Family Products	8
FortiGuard Subscription Services	8
FortiClient	8
FortiMail	9
FortiAnalyzer	9
FortiReporter	9
FortiBridge	9
FortiManager	9
About this document	10
Document conventions	10
Typographic conventions	11
Fortinet documentation	12
Fortinet Knowledge Center	13
Comments on Fortinet technical documentation	13
Customer service and technical support	13
Installing the FortiWiFi unit	15
Package Contents	15
FortiWiFi-60A/AM	15
Mounting	16
Powering on the FortiWiFi unit	16
Powering off the FortiWiFi unit	17
Connecting to the FortiWiFi unit	17
Web-based manager	17
Command line interface	17
Connecting to the web-based manager	18
System Dashboard	19
Command line interface	19
Connecting to the CLI	19
Quick installation using factory defaults	20
Factory defaults	23
Factory default DHCP server configuration	24
Factory default NAT/Route mode network configuration	24

FortiWiFi-60A/AM FortiOS 3.0 MR4 Install Guide	3
01-30004-0283-20070215

Image 3

Contents Install G U I D E Regulatory compliance TrademarksContents Configuring the modem interface Configuring the FortiWiFiUsing a wireless network FortiWiFi FirmwareIndex Page FortiWiFi-60A/AM About the FortiWiFi unitFortiClient Register your FortiWiFi unitFortiGuard Subscription Services Fortinet Family ProductsFortiBridge FortiMailFortiAnalyzer FortiReporterDocument conventions About this documentAddressipv4 Typographic conventionsFortinet documentation FortiGate Install GuideCustomer service and technical support Fortinet Knowledge CenterComments on Fortinet technical documentation Customer service and technical support Package Contents Installing the FortiWiFi unitMounting Powering on the FortiWiFi unitTo power on the FortiWiFi unit SpecificationsTo power off the FortiWiFi unit Connecting to the FortiWiFi unitPowering off the FortiWiFi unit Command line interfaceTo connect to the web-based manager Connecting to the web-based managerSystem Dashboard Connecting to the CLIBits per second 9600 Data bits Parity Quick installation using factory defaultsTo connect to the CLI WelcomeGo to System Network Options Quick installation using factory defaults Factory defaults Factory default NAT/Route mode network configuration Factory default Dhcp server configurationFactory default firewall configuration Factory default Transparent mode network configurationFactory default protection profiles To reset the default settings Go to System Status Restoring the default settingsRestoring the default settings using the web-based manager Restoring the default settings using the CLIRestoring the default settings NAT/Route mode Planning the FortiWiFi configurationExample NAT/Route mode network configuration NAT/Route mode with multiple external network connectionsExample NAT/Route multiple internet connection Transparent modePreparing to configure the FortiWiFi unit in NAT/Route mode NAT/Route mode installationPPPoE setting User name Password Dhcp or PPPoE configurationUsing the web-based manager NAT/Route mode settings Administrator Password InternalTo configure interfaces Go to System Network Interface Configuring basic settingsConfiguring the FortiWiFi unit to operate in NAT/Route mode Adding a default routeVerifying the web-based manager configuration Using the command line interfaceTo set the WAN1 interface to use DHCP, enter To add/change the administrator passwordTo configure interfaces ExampleGet system interface To configure DNS server settingsTo add a default route To set the WAN1 interface to use PPPoE, enterTo connect the FortiWiFi unit Connecting the FortiWiFi unit to the networksNAT/Route mode connections Configuring the networksDNS Settings Transparent mode installationPreparing to configure Transparent mode Transparent mode settings Administrator PasswordTo verify the DNS server settings To change to Transparent mode using the CLIReconnecting to the web-based manager Connecting the FortiWiFi unit to your networkTo connect the FortiWiFi unit running in Transparent mode Set the date and time Next stepsUpdating antivirus and IPS signatures Every Scheduling antivirus and IPS updatesTo update IPS signatures using the CLI Updating the IPS signatures from the CLIWeekly To enable schedule updates from the CLIAdding an override server DailyConfig system autoupdate override set address Set status End To add an override server using the CLINext steps Configuring the modem interface To configure the FortiWiFi-60A using the CLI Selecting a modem modeRedundant mode configuration Stand alone mode configurationEnter the following to configure the dialup account Configuring modem settings To disconnect the modem Connecting and disconnecting the modem in Stand alone modeTo configure modem settings Go to System Network Modem To connect to a dial-up account Go to System Network ModemKeywords and variables Description Default Configuring the modem using the CLIPeermodem1 Adding a Ping Server Adding firewall policies for modem connectionsDead gateway detection FortiWiFi unit as an Access Point Setting up a wireless networkPositioning an Access Point Using multiple access pointsRadio Frequency interface Wireless Equivalent Privacy WEP Wireless SecurityWi-Fi Protected Access WPA Additional security measuresMAC address filtering To disable Ssid Go to System Wireless Settings FortiWiFi operation modesService Set Identifier Access Point modeSetting up the FortiWiFi unit as an Access Point Client modeChanging the operating mode Set the Dhcp settings To set the data security Go to System Wireless SettingsSet the security options Configure the firewall policies Upgrading the firmware using the web-based manager To upgrade the firmware using the web-based managerUpgrading to a new firmware version Execute restore image image.out Upgrading the firmware using the CLITo upgrade the firmware using the CLI Execute restore image Tftp namestr tftpipv4Reverting to a previous firmware version Execute update-nowTo revert to a previous firmware version using the CLI Reverting to a previous firmware version using the CLIExecute restore image Tftp image.out To install firmware from a system reboot Enter Local Address Press Any Key To Download Boot ImagePress any key to display configuration menu Enter Tftp Server AddressDo You Want To Save The Image? y/n Restoring the previous configurationSave as Default firmware/Run image without savingD/R FortiUSB keyBackup and Restore from the FortiUSB key To backup configuration using the CLITo restore configuration using the CLI To configure the USB Auto-Install using the CLI Using the USB Auto-Install featureTesting a new firmware image before installing it Additional CLI Commands for the FortiUSB keyTo test a new firmware image Testing a new firmware image before installing it Type n FortiWiFi unit running v3.x Bios Testing a new firmware image before installing it Numerics Index01-30004-0283-20070215