Fortinet ORTIWIFI-60A /AM manual Upgrading the firmware using the CLI, Execute ping

Page 66

Upgrading to a new firmware version

FortiWiFi Firmware

6Select OK.

The FortiWiFi unit uploads the firmware image file, upgrades to the new firmware version, restarts, and displays the FortiWiFi login. This process takes a few minutes.

7Log into the web-based manager.

8Go to System > Status and check the firmware version to confirm the firmware upgrade is successfully installed.

9Update antivirus and attack definitions. For information about updating antivirus and attack definitions, see the FortiGate Administration Guide.

Upgrading the firmware using the CLI

To use the following procedure, you must have a TFTP server the FortiWiFi unit can connect to.

Note: Installing firmware replaces your current antivirus and attack definitions, along with the definitions included with the firmware release you are installing. After you install new firmware, make sure that antivirus and attack definitions are up to date. You can also use the CLI command execute update-nowto update the antivirus and attack definitions. For details, see the FortiGate Administration Guide.

Note: To use this procedure, you must log in using the admin administrator account, or an administrator account that has system configuration read and write privileges.

To upgrade the firmware using the CLI

1Make sure the TFTP server is running.

2Copy the new firmware image file to the root directory of the TFTP server.

3Log into the CLI.

4Make sure the FortiWiFi unit can connect to the TFTP server.

You can use the following command to ping the computer running the TFTP server. For example, if the IP address of the TFTP server is 192.168.1.168:

execute ping 192.168.1.168

5Enter the following command to copy the firmware image from the TFTP server to the FortiWiFi unit:

execute restore image TFTP <name_str> <tftp_ipv4>

Where <name_str> is the name of the firmware image file and <tftp_ip4> is the IP address of the TFTP server. For example, if the firmware image file name is image.out and the IP address of the TFTP server is 192.168.1.168, enter:

execute restore image image.out 192.168.1.168

The FortiWiFi unit responds with the message:

This operation will replace the current firmware version! Do you want to continue? (y/n)

6Type y.

The FortiWiFi unit uploads the firmware image file, upgrades to the new firmware version, and restarts. This process takes a few minutes.

7Reconnect to the CLI.

66

FortiWiFi-60A/AM FortiOS 3.0 MR4 Install Guide

01-30004-0283-20070215

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Install G U I D E Trademarks Regulatory complianceContents Configuring the FortiWiFi Configuring the modem interfaceUsing a wireless network FortiWiFi FirmwareIndex Page About the FortiWiFi unit FortiWiFi-60A/AMFortinet Family Products Register your FortiWiFi unitFortiGuard Subscription Services FortiClientFortiReporter FortiMailFortiAnalyzer FortiBridgeAbout this document Document conventionsTypographic conventions Addressipv4FortiGate Install Guide Fortinet documentationCustomer service and technical support Fortinet Knowledge CenterComments on Fortinet technical documentation Customer service and technical support Installing the FortiWiFi unit Package ContentsSpecifications Powering on the FortiWiFi unitTo power on the FortiWiFi unit MountingCommand line interface Connecting to the FortiWiFi unitPowering off the FortiWiFi unit To power off the FortiWiFi unitConnecting to the web-based manager To connect to the web-based managerConnecting to the CLI System DashboardWelcome Quick installation using factory defaultsTo connect to the CLI Bits per second 9600 Data bits ParityGo to System Network Options Quick installation using factory defaults Factory defaults Factory default Dhcp server configuration Factory default NAT/Route mode network configurationFactory default Transparent mode network configuration Factory default firewall configurationFactory default protection profiles Restoring the default settings using the CLI Restoring the default settingsRestoring the default settings using the web-based manager To reset the default settings Go to System StatusRestoring the default settings Planning the FortiWiFi configuration NAT/Route modeNAT/Route mode with multiple external network connections Example NAT/Route mode network configurationTransparent mode Example NAT/Route multiple internet connectionNAT/Route mode installation Preparing to configure the FortiWiFi unit in NAT/Route modeNAT/Route mode settings Administrator Password Internal Dhcp or PPPoE configurationUsing the web-based manager PPPoE setting User name PasswordConfiguring basic settings To configure interfaces Go to System Network InterfaceUsing the command line interface Adding a default routeVerifying the web-based manager configuration Configuring the FortiWiFi unit to operate in NAT/Route modeExample To add/change the administrator passwordTo configure interfaces To set the WAN1 interface to use DHCP, enterTo set the WAN1 interface to use PPPoE, enter To configure DNS server settingsTo add a default route Get system interfaceConnecting the FortiWiFi unit to the networks To connect the FortiWiFi unitConfiguring the networks NAT/Route mode connectionsTransparent mode settings Administrator Password Transparent mode installationPreparing to configure Transparent mode DNS SettingsTo change to Transparent mode using the CLI To verify the DNS server settingsReconnecting to the web-based manager Connecting the FortiWiFi unit to your networkTo connect the FortiWiFi unit running in Transparent mode Next steps Set the date and timeUpdating antivirus and IPS signatures Updating the IPS signatures from the CLI Scheduling antivirus and IPS updatesTo update IPS signatures using the CLI EveryDaily To enable schedule updates from the CLIAdding an override server WeeklyTo add an override server using the CLI Config system autoupdate override set address Set status EndNext steps Configuring the modem interface Stand alone mode configuration Selecting a modem modeRedundant mode configuration To configure the FortiWiFi-60A using the CLIEnter the following to configure the dialup account Configuring modem settings To connect to a dial-up account Go to System Network Modem Connecting and disconnecting the modem in Stand alone modeTo configure modem settings Go to System Network Modem To disconnect the modemConfiguring the modem using the CLI Keywords and variables Description DefaultPeermodem1 Adding a Ping Server Adding firewall policies for modem connectionsDead gateway detection Setting up a wireless network FortiWiFi unit as an Access PointPositioning an Access Point Using multiple access pointsRadio Frequency interface Wireless Security Wireless Equivalent Privacy WEPWi-Fi Protected Access WPA Additional security measuresMAC address filtering Access Point mode FortiWiFi operation modesService Set Identifier To disable Ssid Go to System Wireless SettingsSetting up the FortiWiFi unit as an Access Point Client modeChanging the operating mode Set the Dhcp settings To set the data security Go to System Wireless SettingsSet the security options Configure the firewall policies Upgrading the firmware using the web-based manager To upgrade the firmware using the web-based managerUpgrading to a new firmware version Execute restore image Tftp namestr tftpipv4 Upgrading the firmware using the CLITo upgrade the firmware using the CLI Execute restore image image.outExecute update-now Reverting to a previous firmware versionReverting to a previous firmware version using the CLI To revert to a previous firmware version using the CLIExecute restore image Tftp image.out To install firmware from a system reboot Enter Tftp Server Address Press Any Key To Download Boot ImagePress any key to display configuration menu Enter Local AddressFortiUSB key Restoring the previous configurationSave as Default firmware/Run image without savingD/R Do You Want To Save The Image? y/nBackup and Restore from the FortiUSB key To backup configuration using the CLITo restore configuration using the CLI Using the USB Auto-Install feature To configure the USB Auto-Install using the CLITesting a new firmware image before installing it Additional CLI Commands for the FortiUSB keyTo test a new firmware image Testing a new firmware image before installing it Type n FortiWiFi unit running v3.x Bios Testing a new firmware image before installing it Index Numerics01-30004-0283-20070215
Top Page Image Contents