Encore electronic Z8ENCORE000ZCO, UM014605-0208 user manual J6.9-J6.11-Modem Enable/Disable

Page 28

Z8 Encore!® Flash Microcontroller Development Kit

User Manual

Table 7. Configuration Headers and Jumpers (Continued)

24

 

 

Related Headers,

Header

Function

Registers or Devices

J11

SocketModem Power

 

 

(3 V DC/5 V DC)

 

 

 

 

J12

RS-485_1_EN

 

 

 

 

J13

RS-485_2_EN

 

 

 

 

J14

RT_1

 

 

 

 

J15

RT_2

 

 

 

 

Table 8 through Table 13 list jumper information concerning the shunt status, functions, and devices affected of selected jumpers.

Table 8. J6.9–J6.11-Modem Enable/Disable

Shunt Status Function

Device Affected

IN

Modem connector (P2) is

UART1 cannot communicate through P2.

 

disabled

Ports D and F can be assigned to functions

 

 

other than UART1.

OUT

Modem connector (P2) is

If the embedded SocketModem is not in the

 

enabled

socket, UART1 communicates through P2.

Table 9. J6.12–J6.14-Console Enable/Disable

Shunt

 

 

Status

Function

Device Affected

IN

Console connector (P1) is disabled

If J6.12–14 is IN and J10 is IN, Port A

 

 

(3-5) is assigned to IrDA; if J10 is

 

 

OUT Port A (3-5) is assigned to

 

 

UART0.

 

 

 

OUT

Console connector (P1) is enabled

None

 

 

 

UM014605-0208

Z8 Encore!® Evaluation Board

Image 28
Contents Z8 Encore! Flash Microcontroller Development Kit Z8 Encore! Flash Microcontroller Development Kit Revision HistoryRevision Date Level Description Table of Contents Schematics Index Customer Support Kit Contents IntroductionZ8 Encore! Development Kit Contents Software on CD-ROMDevice driver software is installed with ZDS II and resides DocumentationSupported Host System Configuration System/Software RequirementsInstallation Setting up the Evaluation BoardEvaluation Board External Connections Inserting a New Plug Configuration Installing the ZDS II-Z8 Encore! Software Using ZDS Getting StartedIntroduction Features Z8 Encore! Evaluation BoardBlock Diagram Major Z8 Encore! Evaluation Board BlocksZ8 Encore! Evaluation Board Block Diagram MCU LED Anode Assignments LED ArrayFunction/Port G Bit No Serial Communications Devices I2C InterfaceLED Addressing Function/Port E Bit NoSPI Interface IrDA TransceiverDevice/Bit No Value Smart Cable Power and Communication InterfacesExpansion Module Interface Pin No Signal Name Function Direction Comments Z8 Encore! Flash Microcontroller Development Kit Header J6PE7 Header J8 Z8 Encore! Flash Microcontroller Development Kit Header J8 Reset Configuration Headers/Jumpers Configuration Headers and JumpersRelated Headers Header Function Registers or DevicesJ6.12-J6.14-Console Enable/Disable J6.9-J6.11-Modem Enable/DisableShunt Status Function Device Affected J10 IrDA Enable/Disable J9 VrefShunt Status Function Device or Register Affected Function Device or Register AffectedJ13-RS-4851Enable Second Interface J12-RS-4851Enable First InterfaceShunt Position Function Device Affected Second RS-485 interface termination None Resistors disabled Embedded Modem Placement Embedded ModemSales Order Number Part Number Configuration PushbuttonsSchematics Z8 Encore! Flash Microcontroller Development KitPE0 Modem Schematic, Z8F Encore Evaluation Board Z8 Encore! Smart Cable Index I2C Z8 Encore! Flash Microcontroller Development Kit Customer Support As used herein Document Disclaimer