Encore electronic Z8ENCORE000ZCO LED Array, LED Anode Assignments, Function/Port G Bit No

Page 18

Z8 Encore!® Flash Microcontroller Development Kit

User Manual

On-Chip Debugger

Voltage Brownout (VBO) Protection

Power-On Reset (POR)

3.0 V–3.6 V operating voltage with 5 V-tolerant inputs

0 °C–70 °C operating temperature

For further information on the Z8 Encore! family of devices, refer to

Z8 Encore! XP® 64K Series Flash Microcontrollers Product Specification (PS0199).

LED Array

14

The LED array display user information. There are four 7 x 5 LED matrixes. To light up an LED dot the appropriate Anode bit must be 1, and the correlated Cathode must be 0. All Anodes are addressed by Port G, and Cathodes are addressed by Port E. Every LED Matrix is addressed by separate pair of registers. Each register pairs is addressed by a bit of Port E or Port G. Table 1 through Table 4 describe how to address each Anode and Cathode of D1 through D4.

Table 1. LED Anode Assignments

Function/Port G Bit No

6

5

4

3

2

1

0

Anode Row 0

 

 

 

 

 

 

X

Anode Row 1

 

 

 

 

 

X

 

Anode Row 2

 

 

 

 

X

 

 

Anode Row 3

 

 

 

X

 

 

 

Anode Row 4

 

 

X

 

 

 

 

Anode Row 5

 

X

 

 

 

 

 

Anode Row 6

X

 

 

 

 

 

 

Note: Row 0 = Topmost Row

 

 

 

 

 

 

 

UM014605-0208

Z8 Encore!® Evaluation Board

Image 18
Contents Z8 Encore! Flash Microcontroller Development Kit Revision History Z8 Encore! Flash Microcontroller Development KitRevision Date Level Description Table of Contents Schematics Index Customer Support Kit Contents IntroductionZ8 Encore! Development Kit Contents Software on CD-ROMDevice driver software is installed with ZDS II and resides DocumentationSupported Host System Configuration System/Software RequirementsInstallation Setting up the Evaluation BoardEvaluation Board External Connections Inserting a New Plug Configuration Installing the ZDS II-Z8 Encore! Software Using ZDS Getting StartedIntroduction Features Z8 Encore! Evaluation BoardBlock Diagram Major Z8 Encore! Evaluation Board BlocksZ8 Encore! Evaluation Board Block Diagram MCU LED Array LED Anode AssignmentsFunction/Port G Bit No LED Addressing Serial Communications DevicesI2C Interface Function/Port E Bit NoIrDA Transceiver SPI InterfaceDevice/Bit No Value Power and Communication Interfaces Smart CableExpansion Module Interface Pin No Signal Name Function Direction Comments Z8 Encore! Flash Microcontroller Development Kit Header J6PE7 Header J8 Z8 Encore! Flash Microcontroller Development Kit Header J8 Reset Related Headers Configuration Headers/JumpersConfiguration Headers and Jumpers Header Function Registers or DevicesJ6.9-J6.11-Modem Enable/Disable J6.12-J6.14-Console Enable/DisableShunt Status Function Device Affected Shunt Status Function Device or Register Affected J10 IrDA Enable/DisableJ9 Vref Function Device or Register AffectedJ12-RS-4851Enable First Interface J13-RS-4851Enable Second InterfaceShunt Position Function Device Affected Second RS-485 interface termination None Resistors disabled Embedded Modem Placement Embedded ModemSales Order Number Part Number Configuration PushbuttonsSchematics Z8 Encore! Flash Microcontroller Development KitPE0 Modem Schematic, Z8F Encore Evaluation Board Z8 Encore! Smart Cable Index I2C Z8 Encore! Flash Microcontroller Development Kit Customer Support As used herein Document Disclaimer