Enterasys Networks C3G124-24P Installing Optional Mini-GBICs, Preparing to Install a Mini-GBIC

Page 42

Installing Optional Mini-GBICs

Installing Optional Mini-GBICs

This section describes how to install Mini‐GBICs in any of the SFP port slots. It is recommended that the options be installed first in a new installation.

Warning: Do not use optical instruments to view laser output. The use of optical instruments to view laser output increases eye hazard.

Advertencia: No utilizar instrumentos opticos para ver el laser. El uso de instrumentos opticos para ver el laser incrementa el riesgo de perdida de la vision.

Warnhinweis: Benutzen sie keinesfalls optische Hilfmittel, um die Funktion des Lasers zu überprüfen, es könnte ihr Augenlicht gefährden.

Caution: Carefully follow the instructions in this manual to avoid damaging the Mini-GBIC and switch.

The Mini-GBIC and switch are sensitive to static discharges. Use an antistatic wrist strap and observe all static precautions during this procedure. Failure to do so could result in damage to the Mini-GBIC and switch. Always leave the Mini-GBIC in the antistatic bag or an equivalent antistatic container when not installed.

Precaución: Siga las instrucciones del manual para no dañar el Mini-GBIC ni del aparato, puesto que son muy sensible a las descargas de electricidad estática. Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este procedimiento. Si no lo hace, podría dañar el Mini-GBIC o del aparato. Mientras no esté instalado, mantenga el Mini-GBIC en su bolsa antiestática o en cualquier otro recipiente antiestático.

Preparing to Install a Mini-GBIC

Before removing the Mini‐GBIC from the antistatic packaging, it is recommended that you use an antistatic wrist strap (not supplied) to prevent damage from static discharge. To use the wrist strap, refer to the instructions provided with your antistatic wrist strap.

1.Remove the Mini‐GBIC from its packaging.

2.If there is a protective dust cover (see 5 in Figure 3‐1 or Figure 3‐2) in the Mini‐GBIC connector, do not remove it at this time.

SecureStack C3 Installation Guide 3-3

Image 42

Contents

Enterasys SecureStack C3 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide Who Should Use This GuideHow to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guideGetting Help Support@enterasys.comC3G124-24P Stackable Switch OverviewC3G124-24P Stackable Switch C3G124-48P Stackable Switch Redundant Power Supply Capability High-Speed Stack ConnectionsPoE Power over Ethernet Support Powered Device Classifications Usage PD Maximum Power RangeDescription of Mini-GBICs Specification ConnectivityManagement Switch Configuration Using WebViewSwitch Configuration Using CLI Commands Standards CompatibilityLanview Diagnostic LEDs Network Requirements 1000BASE-FX Network 10BASE-TX Network100BASE-TX Network 1000BASE-T NetworkHardware Installation Contents of Switch Carton Quantity Considerations Prior to InstallationUnpacking the Switch Required ToolsInstalling Optional Mini-GBICs Preparing to Install a Mini-GBICInstalling a Mini-GBIC Mini-GBIC with MT-RJ ConnectorMini-GBIC with LC Connector Removing a Mini-GBICInstalling the Switch on a Flat Surface Installing the Rubber FeetChassis Bottom, Rubber Feet Placement Guidelines for Flat Surface Installation Area Guidelines for Switch Installation on Flat SurfaceRack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Attaching the Rackmount Brackets Connecting High-Speed Stacking Cables Configuring Switches in a Stack About SecureStack Switch Operation in a StackConfiguring Switches in a Stack Recommended Procedures to Install New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesConnecting AC and PoE Power AC PowerConnecting AC Power and RPS PoE Redundant Power System Stack Manager SelectionConnecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device Parameter SettingConnecting to a VT Series Terminal 10 Connecting an IBM PC or CompatibleConnecting to a Modem 11 Connecting a VT Series TerminalConnecting to the Network Connecting UTP Cables13 Connecting a UTP Cable Segment to RJ45 Port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to MT-RJ Ports Connecting to the Network Connecting Fiber-Optic Cables to LC Ports 19 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using LanviewC3G124-24P Lanview LEDs C3G124-48P Lanview LEDs Lanview LED Diagnostic Indications Color State Recommended ActionRPS Mgbic Troubleshooting Checklist Refer to the SecureStack C3 Configuration Guide for the IPUsing the Reset Switch Reset SwitchUsing the Reset Switch Using the Reset Switch Troubleshooting Switch Specifications Table A-1 C3G124-24P and C3G124-48P SpecificationsC3G124-48P Mini-GBIC Input/Output Specifications Table A-2 Mini-GBIC Input/Output Port SpecificationsGigabit Ethernet Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXTable A-9 MGBIC-08 Optical Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-11 MGBIC-02 SpecificationsConsole Port Pinout Assignments Regulatory ComplianceTable A-12 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Index MGBIC-LC03 A-5 MGBIC-LC09 A-5