Enterasys Networks C3G124-24P manual C3G124-48P Lanview LEDs

Page 72

Using LANVIEW

Figure 4-2 C3G124-48P LANVIEW LEDs

6

7

 

 

 

 

 

 

 

 

 

 

C3G124-48P

1

CPU LED

5

Manager LED

2

STACK DOWN LED

6

Link/Activity LEDs for 10/100/1000 Mbps RJ45

3

STACK UP LED

 

ports 1 through 48

4

RPS LED for redundant power-source

7

Link/Activity LEDs for 1-Gbps Mini-GBIC ports

 

status

 

45 through 481

1.These Mini-GBIC ports will only establish a link when the RJ45 port equivalent is not linked on a C3G124-48P.(For example, when Mini-GBIC port 45 is linked, RJ45 port 45 is deactivated. When the Mini-GBICis not linked, the RJ45 port 45 is reactivated and can establish a link as long as the Mini-GBIC port 45 is not linked first.)

Table 4‐1 describes the LED indications and provides recommended actions as appropriate.

Note: The terms flashing, blinking, and solid used in Table 4-1indicate the following:

Flashing: LED is flashing randomly.

Blinking: LED is flashing at a steady rate (approximately 50% on, 50% off).

Solid: LED is on steady and not pulsing.

SecureStack C3 Installation Guide 4-3

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Enterasys SecureStack C3 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv About This Guide Who Should Use This GuideHow to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guideGetting Help Support@enterasys.comC3G124-24P Stackable Switch OverviewC3G124-24P Stackable Switch C3G124-48P Stackable Switch Redundant Power Supply Capability High-Speed Stack ConnectionsPoE Power over Ethernet Support Powered Device Classifications Usage PD Maximum Power RangeDescription of Mini-GBICs Specification ConnectivitySwitch Configuration Using WebView Switch Configuration Using CLI CommandsManagement Standards CompatibilityLanview Diagnostic LEDs Network Requirements 10BASE-TX Network 100BASE-TX Network1000BASE-FX Network 1000BASE-T NetworkHardware Installation Considerations Prior to Installation Unpacking the SwitchContents of Switch Carton Quantity Required ToolsInstalling Optional Mini-GBICs Preparing to Install a Mini-GBICInstalling a Mini-GBIC Mini-GBIC with MT-RJ ConnectorMini-GBIC with LC Connector Removing a Mini-GBICInstalling the Switch on a Flat Surface Installing the Rubber FeetChassis Bottom, Rubber Feet Placement Guidelines for Flat Surface Installation Area Guidelines for Switch Installation on Flat SurfaceRack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Attaching the Rackmount Brackets Connecting High-Speed Stacking Cables Configuring Switches in a Stack About SecureStack Switch Operation in a StackConfiguring Switches in a Stack Recommended Procedures to Install New and Existing Stacks Installing a New Stackable System of Up to Eight SwitchesConnecting AC and PoE Power AC PowerConnecting AC Power and RPS PoE Redundant Power System Stack Manager SelectionConnecting to Console Port for Local Management What Is NeededConnecting to an IBM or Compatible Device Parameter SettingConnecting to a VT Series Terminal 10 Connecting an IBM PC or CompatibleConnecting to a Modem 11 Connecting a VT Series TerminalConnecting to the Network Connecting UTP Cables13 Connecting a UTP Cable Segment to RJ45 Port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to MT-RJ Ports Connecting to the Network Connecting Fiber-Optic Cables to LC Ports 19 Cable Connection to LC Fiber-Optic Connectors Completing the Installation Initial Logon to Switch ManagementTroubleshooting Using LanviewC3G124-24P Lanview LEDs C3G124-48P Lanview LEDs Lanview LED Diagnostic Indications Color State Recommended ActionRPS Mgbic Troubleshooting Checklist Refer to the SecureStack C3 Configuration Guide for the IPUsing the Reset Switch Reset SwitchUsing the Reset Switch Using the Reset Switch Troubleshooting Switch Specifications Table A-1 C3G124-24P and C3G124-48P SpecificationsC3G124-48P Mini-GBIC Input/Output Specifications Table A-2 Mini-GBIC Input/Output Port SpecificationsGigabit Ethernet Specifications MGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SXMGBIC-LC03 Specifications 1000BASE-SX MGBIC-LC09 Specifications 1000BASE-LXMGBIC-08 Specifications 1000BASE-ELX MGBIC-02 Specifications 1000BASE-TTable A-9 MGBIC-08 Optical Specifications Table A-11 MGBIC-02 SpecificationsConsole Port Pinout Assignments Regulatory ComplianceTable A-12 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Index MGBIC-LC03 A-5 MGBIC-LC09 A-5

C3G124-24P, C3G124-48P specifications

Enterasys Networks, a leading company in networking solutions, offers a range of high-performance switches designed to meet the demands of modern enterprise networks. Among their notable products are the C3G124-48P and C3G124-24P switches, which deliver robust performance, advanced features, and reliable connectivity essential for today's business environments.

The C3G124-48P is a 48-port managed switch that provides Power over Ethernet (PoE+) capabilities, allowing for the seamless connection and powering of devices such as IP phones, wireless access points, and security cameras. With 740 watts of power budget, this switch can support multiple devices simultaneously, making it an ideal choice for organizations looking to enhance their network infrastructure. The switch also comes equipped with four 10 Gigabit SFP+ uplinks, enabling high-speed data transfer and ensuring the backbone of the network can handle heavy loads with ease.

On the other hand, the C3G124-24P features 24 ports, also with PoE+ functionality, and is designed for smaller setups or branch office deployments. It offers a power budget of 370 watts, which efficiently supports essential devices while remaining cost-effective. Similar to its 48-port counterpart, the C3G124-24P includes four 10 Gigabit SFP+ uplinks, providing flexibility and scalability for various network configurations.

Both switches incorporate advanced Layer 2 and Layer 3 capabilities, which include features such as VLAN support, link aggregation, and static routing. This versatility allows for effective traffic management and segmentation, which is crucial for maintaining a high-performing network. The switches also support security features like Access Control Lists (ACLs) and port security, ensuring that the network is protected from unauthorized access and potential threats.

Additionally, Enterasys Networks provides cloud-managed options for both models, allowing organizations to manage and monitor their network via a user-friendly interface. This cloud integration facilitates real-time alerts, configuration changes, and troubleshooting, empowering IT teams to respond swiftly to any issues that may arise.

Overall, the Enterasys Networks C3G124-48P and C3G124-24P switches are designed with scalability, power efficiency, and security in mind, making them suitable for a variety of applications from enterprise deployments to small business environments. With their cutting-edge technology and comprehensive feature sets, these switches provide businesses with the reliable networking solutions they need to thrive in today's digital landscape.
Top Page Image Contents