Enterasys Networks C3G124-48P, C3G124-24P manual Mgbic

Page 75

Using LANVIEW

Table 4-1 LANVIEW LED Diagnostic Indications (continued)

LED	Color State	Recommended Action

Link/	Off	1.	No link.
Activity		2.	No activity or port in standby.
(RJ45 PoE
		3.	The port is deactivated because the
ports)
			Mini-GBIC port with the same port number

is linked.

None.

None.

None.

		Green	Solid. Port is linked, but the interface is not	None.
			receiving any traffic. PoE power is available.

			Blinking. Port is linked and traffic is being	None.
			received or transmitted by the interface. PoE
			power is available.

		Amber	Solid. Port is linked, but traffic is not being	1. Check the attached powered device
			received or transmitted by the interface. PoE	to see if it is defective.
			power has failed.	2. Internal power supply failed, contact
			PoE power may have been deactivated	2. Internal power supply failed, contact
			PoE power may have been deactivated	Enterasys Networks for technical
			because of excessive power requirement or	support.
			deactivated by configuration.
			Power Supply failed.

			Blinking. Port is linked and traffic is being	1. Check the attached powered device
			received or transmitted by the interface. PoE	to see if it is defective.
			power has failed.	2. Internal power supply failed, contact
			PoE power may have been deactivated	2. Internal power supply failed, contact
			PoE power may have been deactivated	Enterasys Networks for technical
			because of excessive power requirement or	support.
			deactivated by configuration.
			Power supply failed.

	Link/	Off	1. No link.	None.
	Activity		2. No activity or port in standby.	None.
	(MGBIC		2. No activity or port in standby.	None.

		Green	Solid. Port is linked, but the interface is not	None.
	ports)	Green	Solid. Port is linked, but the interface is not	None.
			receiving any traffic.

			Blinking. Port is linked and traffic is being	None.
			received or transmitted by the interface.

4-6 Troubleshooting

Image 75

Contents

Enterasys SecureStack C3 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC Firmware License Agreement Viii Page Page Contents Troubleshooting Figures Xiv Who Should Use This Guide About This GuideHow to Use This Guide Related DocumentsFor Refer to Following conventions are used in this guide Conventions Used in This GuideSupport@enterasys.com Getting HelpOverview C3G124-24P Stackable SwitchC3G124-24P Stackable Switch C3G124-48P Stackable Switch High-Speed Stack Connections Redundant Power Supply CapabilityPowered Device Classifications Usage PD Maximum Power Range PoE Power over Ethernet SupportConnectivity Description of Mini-GBICs SpecificationStandards Compatibility Switch Configuration Using WebViewSwitch Configuration Using CLI Commands ManagementLanview Diagnostic LEDs Network Requirements 1000BASE-T Network 10BASE-TX Network100BASE-TX Network 1000BASE-FX NetworkHardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Contents of Switch Carton QuantityPreparing to Install a Mini-GBIC Installing Optional Mini-GBICsMini-GBIC with MT-RJ Connector Installing a Mini-GBICRemoving a Mini-GBIC Mini-GBIC with LC ConnectorInstalling the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Area Guidelines for Switch Installation on Flat Surface Guidelines for Flat Surface InstallationRack Mounting the Switch Guidelines for Rackmount InstallationAttaching Brackets and Installing in Rack Attaching the Rackmount Brackets Connecting High-Speed Stacking Cables About SecureStack Switch Operation in a Stack Configuring Switches in a StackConfiguring Switches in a Stack Installing a New Stackable System of Up to Eight Switches Recommended Procedures to Install New and Existing StacksAC Power Connecting AC and PoE PowerConnecting AC Power and RPS Stack Manager Selection PoE Redundant Power SystemWhat Is Needed Connecting to Console Port for Local ManagementParameter Setting Connecting to an IBM or Compatible Device10 Connecting an IBM PC or Compatible Connecting to a VT Series Terminal11 Connecting a VT Series Terminal Connecting to a ModemConnecting UTP Cables Connecting to the Network13 Connecting a UTP Cable Segment to RJ45 Port 14 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Connecting Fiber-Optic Cables to MT-RJ Ports Connecting to the Network Connecting Fiber-Optic Cables to LC Ports 19 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationUsing Lanview Troubleshooting C3G124-24P Lanview LEDs C3G124-48P Lanview LEDs Color State Recommended Action Lanview LED Diagnostic IndicationsRPS Mgbic Refer to the SecureStack C3 Configuration Guide for the IP Troubleshooting ChecklistReset Switch Using the Reset SwitchUsing the Reset Switch Using the Reset Switch Troubleshooting Table A-1 C3G124-24P and C3G124-48P Specifications Switch SpecificationsC3G124-48P Table A-2 Mini-GBIC Input/Output Port Specifications Mini-GBIC Input/Output SpecificationsMGBIC-LC01/MGBIC-MT01 Specifications 1000BASE-SX Gigabit Ethernet SpecificationsMGBIC-LC09 Specifications 1000BASE-LX MGBIC-LC03 Specifications 1000BASE-SXTable A-11 MGBIC-02 Specifications MGBIC-08 Specifications 1000BASE-ELXMGBIC-02 Specifications 1000BASE-T Table A-9 MGBIC-08 Optical SpecificationsConsole Port Pinout Assignments Regulatory ComplianceTable A-12 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Index MGBIC-LC03 A-5 MGBIC-LC09 A-5