Mark Levinson N390S owner manual Track repeat LED, Next/f.fwd button, Stop/drawer

Page 21

13. track repeat LED

This LED is lit when the Nº390S is set to repeat a single track endlessly. This feature is accessed using the repeat button (see number 7, page 19).

14. next/f.fwd button

Pressing this button momentarily will advance the Nº390S to the beginning of the next track. Pressing and holding this button will instead perform a fast forward scan of the music, reminiscent of the fast forward function found on many tape decks. This scanning mode may be either audible or silent (according to your choice in the setup: sound menu; see Special Functions), and it allows you to quickly find a particular point within a track.

15. stop/drawer

Pressing this button once while a disc is playing will stop the disc, resulting in the total number of tracks and the total time on the disc being displayed. (Both the time on disc and the time remaining LEDs are lit to clarify the meaning of the information being displayed at this point.) Pressing this button once the disc has stopped, or if there is no disc in the transport, will cause the drawer to open.

Pressing the stop/drawer button will cause an open drawer to	21
close. If it senses a disc in the drawer, the Nº390S will confirm
its internal conversion rate on the display (24-bit, 352kHz)
and then read the disc’s table of contents so that it may
display the total number of tracks and the total time on the
disc for your information. If a custom play list exists for the
disc, the total number of tracks and the total time of the play
list is displayed instead.

16. time on disc and time remaining LED indicators

These LEDs are used to indicate which of the four available display modes the Nº390S is in. The four indications of time that can be displayed are:

•time elapsed in track (neither LED lit)

•time elapsed on disc (time on disc LED lit)

•time remaining on track (time remaining LED lit)

•time remaining on disc (time on disc and time remaining

LEDs lit)

These four options are accessed by selecting the TIMES mode (using the mode button) and repeatedly pressing the mode + or mode – buttons, which cycle forward or backward through the four modes, respectively.

Image 21

Contents Nº390S Processor Page Important Safety Instructions Customer Support Table of Contents Page Page Unpacking the Nº390S Remove the Transport Screw Placement Unpacking and PlacementOperating Voltage Frequency Quick Start Connect the Nº390S to AC powerTurn off your associated components Remove the transport screw from the bottom of the Nº390S4a. If going direct from the Nº390S to an amplifier Break-in PeriodNew Generation Special Design FeaturesPage Page Page Display intensity Front Panel, Nº390SSpecial Mode Indicator Track IndicatorInfrared Transceiver within display Mode button Time IndicatorHdcd indicator Repeat buttonDrawer Mode and mode + buttons Disc repeat LEDPrev/rew button Track repeat LED Time on disc and time remaining LED indicatorsNext/f.fwd button Stop/drawerPause button Play buttonStandby & Standby LED Rear Panel, Nº390S AC power input and switchDigital Outputs Balanced analog outputs Digital inputsExternal IR input Single-ended analog outputsCommunication ports Standard Link Cables Amplifier Link Cables Remote Control, Nº390S Stop/dwr Mode buttonsPause B repeat buttonNumeric Keypad Polarity Other Operational Buttons TimeRpt disc/trk MuteVolume + volumeBattery Compartment Analog Input SwitchingOptimum IR Reception Window Conditions that Affect IR PerformanceConnecting AC Mains Connecting Digital Audio Sources Setup and InstallationPage Loading a CD Playing a CD Random Play Basic OperationTo load a CD Press stop/drawerTo do this Navigating the Disc Direct Time AccessPause Repeat Disc Repeat Track Programming the Nº390S Repeat Polarity Introduction to Play ListsImportant Note To assemble a new play list Assembling a Play ListReviewing a Play List Programming by Omission Saving a Play ListTo save a play list To review your play list before playing itDeleting a Track from a Play List Adding a Track to a To delete a selectionTo do so Erasing Play Lists from Memory Why Polarity Programming? Overriding a Play ListTo temporarily override a previously saved play list Whole-Disc Polarity Programming Track-by-Track Polarity Press and hold the mode + button. The display will showOverriding a Polarity Program Special FunctionsSound Menu Items Fixed/Variable VolumeSilent/Audible Cueing Balance ControlStandby Link Link Menu Items Locked VolumeName Link Play LinkInput Names AUX IN’s Menu Items Display LinkChanging Link Options Sleep Timer Using Learning Remote Controls Teaching Nº390S Front Panel CommandsTo change between manual and timed/ automatic standby Teaching Other Nº390S Commands Place the Nº390S in its front panel teaching mode Command Display Nº390S won’t function, and the display is dark TroubleshootingDisplay is lit, but there is no output Nº390S display reads no DiscLinked functions don’t work Remote Control doesn’t operate the Nº390SCare and Maintenance Specifications Output Complement Other I/O Dimensions Installation Notes

Related manuals

Manual 4 pages 7.64 Kb