Mark Levinson N390S Setup and Installation, Connecting AC Mains Connecting Digital Audio Sources

Page 36

Caution!

Connecting AC Mains

36Connecting Digital Audio Sources

Setup and Installation

For your protection, review “Important Safety Instructions” before you install your Nº390S.

Plug the female end of the AC power cord into the appropriate socket on the rear panel of the Nº390S, being certain to seat it firmly, all the way into the receptacle.

Double-check to make sure that the AC power switch is in the off position (the side of the switch with an “O” should be depressed), and also that the voltage indicated on your Nº390S corresponds to the normal voltage for your country. (Connecting a 120-volt Nº390S to a 220-volt AC outlet is not a good idea.)

Plug the male end of the power cord into the wall outlet, and then turn on the power switch located on the rear panel of the Nº390S (by depressing the side of the switch that has a single vertical line like this: “”).

The Nº390S incorporates EIAJ optical and RCA digital input connectors for up to two additional digital sources. (See Rear panel, Nº390S.)

For optical digital interconnection, we recommend the use of better quality optical EIAJ cable. Your dealer can help you select an appropriate cable for your system.

Using appropriate cables, connect an output of each additional source (laser disc, digital tape, etc.) to the appropriate input on your Nº390S.

Image 36

Contents Nº390S Processor Page Important Safety Instructions Customer Support Table of Contents Page Page Unpacking and Placement Unpacking the Nº390S Remove the Transport Screw PlacementOperating Voltage Frequency Connect the Nº390S to AC power Quick StartTurn off your associated components Remove the transport screw from the bottom of the Nº390SBreak-in Period 4a. If going direct from the Nº390S to an amplifierSpecial Design Features New GenerationPage Page Page Front Panel, Nº390S Display intensitySpecial Mode Indicator Track IndicatorInfrared Transceiver within display Time Indicator Mode buttonHdcd indicator Repeat buttonDrawer Mode and mode + buttons Disc repeat LEDPrev/rew button Time on disc and time remaining LED indicators Track repeat LEDNext/f.fwd button Stop/drawerPlay button Pause buttonStandby & Standby LED AC power input and switch Rear Panel, Nº390SDigital Outputs Digital inputs Balanced analog outputsSingle-ended analog outputs External IR inputCommunication ports Standard Link Cables Amplifier Link Cables Remote Control, Nº390S Mode buttons Stop/dwrPause B repeat buttonNumeric Keypad Other Operational Buttons Time Polarity Rpt disc/trk Mute+ volume VolumeBattery Compartment Analog Input SwitchingConditions that Affect IR Performance Optimum IR Reception WindowSetup and Installation Connecting AC Mains Connecting Digital Audio SourcesPage Basic Operation Loading a CD Playing a CD Random PlayTo load a CD Press stop/drawerNavigating the Disc Direct Time Access To do thisPause Repeat Disc Repeat Track Programming the Nº390S Repeat Polarity Introduction to Play ListsImportant Note Assembling a Play List To assemble a new play listProgramming by Omission Saving a Play List Reviewing a Play ListTo save a play list To review your play list before playing itDeleting a Track from a Play List Adding a Track to a To delete a selectionTo do so Erasing Play Lists from Memory Why Polarity Programming? Overriding a Play ListTo temporarily override a previously saved play list Press and hold the mode + button. The display will show Whole-Disc Polarity Programming Track-by-Track PolaritySpecial Functions Overriding a Polarity ProgramFixed/Variable Volume Sound Menu ItemsSilent/Audible Cueing Balance ControlLink Menu Items Locked Volume Standby LinkName Link Play LinkAUX IN’s Menu Items Display Link Input NamesChanging Link Options Sleep Timer Using Learning Remote Controls Teaching Nº390S Front Panel CommandsTo change between manual and timed/ automatic standby Teaching Other Nº390S Commands Place the Nº390S in its front panel teaching mode Command Display Troubleshooting Nº390S won’t function, and the display is darkDisplay is lit, but there is no output Nº390S display reads no DiscRemote Control doesn’t operate the Nº390S Linked functions don’t workCare and Maintenance Specifications Output Complement Other I/O Dimensions Installation Notes

Related manuals

Manual 4 pages 7.64 Kb