Mark Levinson N390S owner manual Command Display

Page 55

Special Commands Table

5.Repeat the process of “teaching” new special commands until all desired commands have been learned by your remote control.

If you take longer than approximately ten seconds between button pushes, the Nº390S will time out and return to normal operation. If this occurs, return to step #1 in this section. You may move through the entire list by pressing repeat.

6.When finished, return to normal operation by allowing the Nº390S to “time out.”

The Nº390S will “time out” and return to normal operation after approximately ten seconds.

Command

Display

 

positive control for operate

OPERATE

 

 

 

 

positive control for standby

STANDBY

 

 

 

 

positive control for stop

JUST STOP

 

 

 

 

set display intensity to off

DISPLAY 0

 

 

 

 

set display intensity to medium

DISPLAY 2

 

 

 

 

positive control for unpause

UNPAUSE

 

 

 

 

positive control for pause

PAUSE

 

 

 

 

positive control for leaving the repeat mode

NO REPEAT

55

 

 

 

positive control for open drawer

OPEN

 

 

 

 

positive control for close drawer

CLOSE

 

 

 

 

positive control for random play

RANDOM

 

 

 

 

positive control for selecting analog inputs

ANALOG

 

 

 

 

positive control for selecting digital inputs

DIGITAL

 

 

 

 

positive control for program –

PROG –

 

 

 

 

positive control for program +

PROG +

 

 

 

 

Select CD input

SET CD

 

 

 

 

Select RCA input

SET RCA

 

 

 

 

Select optical (EIAJ) input

SET OPT

 

 

 

 

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Nº390S Processor Page Important Safety Instructions Customer Support Table of Contents Page Page Unpacking the Nº390S Remove the Transport Screw Placement Unpacking and PlacementOperating Voltage Frequency Remove the transport screw from the bottom of the Nº390S Connect the Nº390S to AC powerQuick Start Turn off your associated components4a. If going direct from the Nº390S to an amplifier Break-in PeriodNew Generation Special Design FeaturesPage Page Page Display intensity Front Panel, Nº390STrack Indicator Special Mode IndicatorInfrared Transceiver within display Mode button Time IndicatorRepeat button Hdcd indicatorDrawer Disc repeat LED Mode and mode + buttonsPrev/rew button Stop/drawer Time on disc and time remaining LED indicatorsTrack repeat LED Next/f.fwd buttonPause button Play buttonStandby & Standby LED Rear Panel, Nº390S AC power input and switchDigital Outputs Balanced analog outputs Digital inputsExternal IR input Single-ended analog outputsCommunication ports Standard Link Cables Amplifier Link Cables Remote Control, Nº390S B repeat button Mode buttonsStop/dwr PauseNumeric Keypad Mute Other Operational Buttons TimePolarity Rpt disc/trkAnalog Input Switching + volumeVolume Battery CompartmentOptimum IR Reception Window Conditions that Affect IR PerformanceConnecting AC Mains Connecting Digital Audio Sources Setup and InstallationPage Press stop/drawer Basic OperationLoading a CD Playing a CD Random Play To load a CDTo do this Navigating the Disc Direct Time AccessPause Repeat Disc Repeat Track Repeat Polarity Introduction to Play Lists Programming the Nº390SImportant Note To assemble a new play list Assembling a Play ListTo review your play list before playing it Programming by Omission Saving a Play ListReviewing a Play List To save a play listTo delete a selection Deleting a Track from a Play List Adding a Track to aTo do so Overriding a Play List Erasing Play Lists from Memory Why Polarity Programming?To temporarily override a previously saved play list Whole-Disc Polarity Programming Track-by-Track Polarity Press and hold the mode + button. The display will showOverriding a Polarity Program Special FunctionsBalance Control Fixed/Variable VolumeSound Menu Items Silent/Audible CueingPlay Link Link Menu Items Locked VolumeStandby Link Name LinkInput Names AUX IN’s Menu Items Display LinkChanging Link Options Sleep Timer Teaching Nº390S Front Panel Commands Using Learning Remote Controls To change between manual and timed/ automatic standby Teaching Other Nº390S Commands Place the Nº390S in its front panel teaching mode Command Display Nº390S display reads no Disc TroubleshootingNº390S won’t function, and the display is dark Display is lit, but there is no outputLinked functions don’t work Remote Control doesn’t operate the Nº390SCare and Maintenance Specifications Output Complement Other I/O Dimensions Installation Notes
Related manuals
Manual 4 pages 7.64 Kb
Top Page Image Contents