Cypress CY62146ESL manual Maximum Ratings, Operating Range, Electrical Characteristics

CY62146ESL MoBL→

Maximum Ratings

Exceeding the maximum ratings may impair the useful life of the device. These user guidelines are not tested.

Storage Temperature	–65°C to +150°C
Ambient Temperature with
Power Applied	–55°C to +125°C
Supply Voltage to Ground Potential	–0.5V to 6.0V
DC Voltage Applied to Outputs
in High-Z State[4, 5]	–0.5V to 6.0V
DC Input Voltage[4, 5]	–0.5V to 6.0V

Output Current into Outputs (LOW)			20 mA
Static Discharge Voltage			>2001V
(MIL-STD-883, Method 3015)
Latch up Current			>200 mA
Operating Range
Device	Range	Ambient	[6]
		Temperature	VCC
CY62146ESL	Industrial	–40°C to +85°C	2.2V–3.6V,
			and
			4.5V–5.5V

Electrical Characteristics

Over the Operating Range

45 ns

Parameter

Description

Test Conditions

Min

Typ [3]

Max

Unit

VOH

Output HIGH Voltage

2.2

< VCC

< 2.7

IOH = –0.1 mA

2.0

V

2.7

< VCC

< 3.6

IOH = –1.0 mA

2.4

4.5

< VCC

< 5.5

IOH = –1.0 mA

2.4

VOL

Output LOW Voltage

2.2

< VCC

< 2.7

IOL = 0.1 mA

0.4

V

2.7

< VCC

< 3.6

IOL = 2.1mA

0.4

4.5

< VCC

< 5.5

IOL = 2.1mA

0.4

VIH

Input HIGH Voltage

2.2

< VCC

< 2.7

1.8

VCC + 0.3

V

2.7

< VCC

< 3.6

2.2

VCC + 0.3

4.5

< VCC

< 5.5

2.2

VCC + 0.5

VIL

Input LOW Voltage

2.2

< VCC

< 2.7

–0.3

0.6

V

2.7

< VCC

< 3.6

–0.3

0.8

4.5

< VCC < 5.5

–0.5

0.8

IIX

Input Leakage Current

GND < VI < VCC

–1

+1

μA

IOZ

Output Leakage Current

GND < VO < VCC, Output Disabled

–1

+1

μA

ICC

VCC Operating Supply

f = fmax = 1/tRC

VCC = VCCmax

15

20

mA

Current

f = 1 MHz

IOUT = 0 mA, CMOS levels

2

2.5

ISB1

Automatic CE Power

> VCC − 0.2V, VIN > VCC – 0.2V or VIN < 0.2V,

1

7

μA

CE

down Current — CMOS

f = fmax (Address and Data Only),

Inputs

f = 0 (OE, BHE,

BLE

and WE), VCC = VCC(max)

ISB2

Automatic CE Power

> V

– 0.2V, V

> V

– 0.2V or V

< 0.2V,

1

7

μA

CE

CC

CC

down Current — CMOS

f = 0, V

IN

IN

CC

= VCC(max)

Inputs

Notes

4.VIL(min) = –2.0V for pulse durations less than 20 ns.

5.VIH(max) = VCC + 0.75V for pulse durations less than 20 ns.

6.Full Device AC operation assumes a 100 μs ramp time from 0 to VCC (min) and 200 μs wait time after VCC stabilization.

Document #: 001-43142 Rev. ** Page 3 of 12

[+] Feedback