Connect Tech CTIM-00044 user manual Set the IP Address Using the Web Configuration Manager

Page 22

Connect Tech Blue Heat/Net Sync User Manual

Set the IP Address Using the Web Configuration Manager

NOTE: If you use the Windows Configuration Manager and use Auto Discover to locate your Blue Heat/Net Sync on the network, you can right-click and launch the Web Configuration Manager from there.

You only need to use the route add command if you choose not to use the Configuration Manager found on the CD that accompanied your Blue Heat/Net Sync unit.

From the command prompt of your computer, run: route add A.B.C.0 mask 255.255.255.0 <current IP of your host machine> Be sure to replace the .D from the Blue Heat/Net Sync‟s IP with a 0 (zero). Open your browser and put the Blue Heat/Net Sync‟s IP in the address bar (i.e. A.B.C.D) This will open the WCM. Log in (default login is wcm and the default password is password) and assign the static IP or change the IP to 0.0.0.0 if you are using a DHCP assigned IP.

Set the IP Address Using the Serial Configuration Manager

Insert your CD into the computer and complete the following steps:

1.Once your CD has been inserted, the Driver/Software Installation menu should appear. If it doesn‟t, double-click on ctisetup.htm.

2.Click View in the Blue Heat/Net Sync Software section and then Connect in the Serial Configuration Manager section. This will launch HyperTerminal that comes with Windows XP.

3.Unplug the power to the Blue Heat/Net Sync and plug it back in. Light indicators 1 to 4 will blink sequentially. This sequential flashing will last for 30 seconds. You must log in during this window.

4.During this sequential flashing, type the word password into the HyperTerminal window. Be careful you do not miss the window of opportunity to enter the password.

5.You now have access to the Serial Configuration Manager (SCM). An scm> prompt is ready to accept commands. If you do not see this prompt, unplug the power and repeat the steps above.

If you wish to set a dynamic IP address enter the following: net dhcp=yes

save exit

If you wish to set a static IP address, enter the following, substituting xxx.xxx.xxx.xxx with the static IP you wish to assign:

net mip=xxx.xxx.xxx.xxx save

exit

Close the HyperTerminal. You may now disconnect the DB-25 cable from your PC and connect it to any serial device

.

22

Revision 0.03

Image 22
Contents Blue Heat/Net Sync Limited Lifetime Warranty Email/Internet Telephone/FacsimileMail/Courier Preliminary Testing is still pending Class a Computing DeviceTable of Contents Installing the Blue Heat/Net Sync Configuration Manager List of Figures List of Tables Introduction Blue Heat/Net Sync Installation Overview Understanding Virtual COM PortsConnecting the Blue Heat/Net Sync to Your Network Ethernet LEDsSerial Port LEDs Connecting Serial DevicesConnections Blue Heat/Net Synchronous Clocking RS-422/V.11 ConnectionsLoopback Connectors Recommended Pinouts for V.28 RS-232 Loopback ConnectorDC Power Connector Connecting PowerPhoenix Locking Screw Terminal Connector 5VDC Activating the Special Operations Mode and Default Settings Selecting a Special OperationPower On Diagnostics LED Error CodesCRC Connect Tech SCM Serial Configuration Manager Setting a Static or Dynamic IP AddressSCM Cabling requirements Set the IP Address Using the Web Configuration Manager Set the IP Address Using the Serial Configuration ManagerSerial Configuration Manager SCM Application Configuration ManagerBootloader  Operating System SoftwareConfiguration Data Space CDS CDS Configuration Data SpaceAccess to CDS Parameters DescriptionSCM Command Reference SCM Serial Configuration ManagerGetting Access to the SCM Brief Command ListCommand Details Boot Syntax boot mode= file= delay=Yes Myip= mip= Save File= WCM Web Configuration Manager Signing In to the Web Configuration ManagerBlue Heat/Net Sync Settings Configure Advanced Serial Settings Configure Blue Heat/Net Sync SettingsPage Configure Firmware Restore DefaultsRestore Default Settings Saving To FlashMonitoring Your Blue Heat/Net Monitor Serial Port TrafficMonitor TCP/IP Statistics Monitor Network TrafficMy Blue Heat/Net Sync My Blue Heat/Net Sync Hardware Details Installing the Blue Heat/Net Sync Configuration Manager Blue Heat/Net Sync Driver/Software Installation CDBlue Heat/Net Sync Software Installation Screen Page Page Running the Configuration Manager Device InstallationConfigure Default Blue Heat/Net Sync Add New Blue Heat/Net SyncAuto Discover Blue Heat/Net Sync Auto Discover Blue Heat/Net Sync ScreenUpgrade using WCM Web Configuration Manager Upgrade using SCM Serial Configuration ManagerChip Selects Hardware InformationHardware Resources Chip SelectsGpio Bits Direction Usage Base Address MapInterrupts Address Range hexColdFire 5272 Bus Iusc AccessMemory Map of Iusc and PLD Functions A11 A10PLD Memory Map Table PLD Resource AccessAddress Area item Register Offset Accessed Hex FunctionBit Serial Data transfers only IUSC-1 Offset Reg Name Valid Bit Descriptions Reset Values Hex PLD RegistersFSM CTSM1 CTSM0 PLD ID System Block Diagrams Revision Port Settings, Clock Setup and General Settings BHNPortSettingsSerial Mode smode Async MonoSync BiSync Trans-BiSync Iusc Clocking Logic Blue Heat/Net Sync Specifications Protocol Descriptions TelnetDB-25 Female Pinouts Mode Equivalent Standard Electrical Typical VoltagePinouts DB-25 Female PinoutsDB-9 Female Pinouts DB-9 Female PinoutsRack Mount Option Boot Settings Default SettingsNetwork Settings SCM Operation SettingsUsing SCM Common Configuration SetupsStatic IP Setup Using WCMHow the Blue Heat/Net Sync Boots Up Dhcp SetupBootup Sequence Bootup SequenceFlowchart of Special Operations Mode using the reset button Asynchronous Communications TutorialDifferential Line Interfaces Serial Line Interface TutorialRS-232 Line Interface RS485/RS422/V.11 DetailsBasic 4-Wire, Full Duplex Communications Multi-drop 4-Wire, Full Duplex Communications Basic Wire, Half Duplex Multi-drop ConnectionBus Contention on Differential Multi-drop Networks Termination Resistors in Differential Networks Termination Resistors in Differential Networks