Connect Tech CTIM-00044 user manual Running the Configuration Manager, Device Installation

Page 44

Connect Tech Blue Heat/Net Sync User Manual

Running the Configuration Manager

If you chose the option to launch the Blue Heat/Net Sync Configuration Manager after installation, the main Configuration Manager window should now be open on your screen. If you did not, you can launch it from the CTI default folder or whichever folder you chose during the installation.

Figure 26: My Blue Heat/Net Sync Places Screen

Device Installation

Select My Blue Heat/Net Sync Places from the main Configuration window. (NOTE: If there is no Blue Heat/Net Sync installed, you will be prompted to auto discover a Blue Heat/Net Sync on your network. If you choose to do so, click Yes and then jump ahead to the Auto Discover Blue Heat/Net Sync section)

Right-click on My Blue Heat/Net Sync Places or click on the Action menu to pull up the sub menu options.

There are three ways to install a Blue Heat/Net Sync device: Configure Default Blue Heat/Net Sync, Add New Blue Heat/Net Sync or Auto Discover Blue Heat/Net Sync.

44	Revision 0.03

Image 44

Contents Blue Heat/Net Sync Limited Lifetime Warranty Mail/Courier Telephone/FacsimileEmail/Internet Preliminary Testing is still pending Class a Computing DeviceTable of Contents Installing the Blue Heat/Net Sync Configuration Manager List of Figures List of Tables Introduction Blue Heat/Net Sync Installation Overview Understanding Virtual COM PortsConnecting the Blue Heat/Net Sync to Your Network Ethernet LEDsConnections Connecting Serial DevicesSerial Port LEDs Blue Heat/Net Synchronous Clocking RS-422/V.11 ConnectionsLoopback Connectors Recommended Pinouts for V.28 RS-232 Loopback ConnectorPhoenix Locking Screw Terminal Connector Connecting PowerDC Power Connector 5VDC Activating the Special Operations Mode and Default Settings Selecting a Special OperationPower On Diagnostics LED Error CodesCRC Connect Tech SCM Cabling requirements Setting a Static or Dynamic IP AddressSCM Serial Configuration Manager Set the IP Address Using the Web Configuration Manager Set the IP Address Using the Serial Configuration ManagerConfiguration Manager BootloaderSerial Configuration Manager SCM Application  Operating System SoftwareCDS Configuration Data Space Access to CDS ParametersConfiguration Data Space CDS DescriptionSCM Serial Configuration Manager Getting Access to the SCMSCM Command Reference Brief Command ListCommand Details Boot Syntax boot mode= file= delay=Yes Myip= mip= Save File= WCM Web Configuration Manager Signing In to the Web Configuration ManagerBlue Heat/Net Sync Settings Configure Advanced Serial Settings Configure Blue Heat/Net Sync SettingsPage Configure Firmware Restore DefaultsRestore Default Settings Saving To FlashMonitoring Your Blue Heat/Net Monitor Serial Port TrafficMy Blue Heat/Net Sync Monitor Network TrafficMonitor TCP/IP Statistics My Blue Heat/Net Sync Hardware Details Installing the Blue Heat/Net Sync Configuration Manager Blue Heat/Net Sync Driver/Software Installation CDBlue Heat/Net Sync Software Installation Screen Page Page Running the Configuration Manager Device InstallationConfigure Default Blue Heat/Net Sync Add New Blue Heat/Net SyncAuto Discover Blue Heat/Net Sync Auto Discover Blue Heat/Net Sync ScreenUpgrade using WCM Web Configuration Manager Upgrade using SCM Serial Configuration ManagerHardware Information Hardware ResourcesChip Selects Chip SelectsBase Address Map InterruptsGpio Bits Direction Usage Address Range hexIusc Access Memory Map of Iusc and PLD FunctionsColdFire 5272 Bus A11 A10PLD Resource Access Address Area item Register Offset Accessed HexPLD Memory Map Table FunctionBit Serial Data transfers only IUSC-1 Offset Reg Name Valid Bit Descriptions Reset Values Hex PLD RegistersFSM CTSM1 CTSM0 PLD ID System Block Diagrams Revision Port Settings, Clock Setup and General Settings BHNPortSettingsSerial Mode smode Async MonoSync BiSync Trans-BiSync Iusc Clocking Logic Blue Heat/Net Sync Specifications Protocol Descriptions TelnetMode Equivalent Standard Electrical Typical Voltage PinoutsDB-25 Female Pinouts DB-25 Female PinoutsDB-9 Female Pinouts DB-9 Female PinoutsRack Mount Option Default Settings Network SettingsBoot Settings SCM Operation SettingsCommon Configuration Setups Static IP SetupUsing SCM Using WCMHow the Blue Heat/Net Sync Boots Up Dhcp SetupBootup Sequence Bootup SequenceFlowchart of Special Operations Mode using the reset button Asynchronous Communications TutorialSerial Line Interface Tutorial RS-232 Line InterfaceDifferential Line Interfaces RS485/RS422/V.11 DetailsBasic 4-Wire, Full Duplex Communications Multi-drop 4-Wire, Full Duplex Communications Basic Wire, Half Duplex Multi-drop ConnectionBus Contention on Differential Multi-drop Networks Termination Resistors in Differential Networks Termination Resistors in Differential Networks