Connect Tech CTIM-00044 user manual Preliminary Testing is still pending, Class a Computing Device

Page 4

Connect Tech Blue Heat/Net Sync User Manual

Certification Statements

Preliminary: Testing is still pending.

Class A Computing Device

Connect Tech Inc. declares that the product(s) covered by the contents of this manual have been tested and found compliant with the below listed standards as required by the Electromagnetic Compatibility (EMC) Directive for General Immunity Compliance.

EN 55022	Conducted and Radiated emissions
CISPR 22	Class A
EN 55024	Immunity to Disturbances
EN 61000-4-2	EN 61000-4-4		EN 61000-4-6	EN 61000-3-2 Exempt
EN 61000-4-3	EN 61000-4-5		EN 61000-4-11	EN 61000-3-3 Pass
The above satisfy the requirements of:
USA:		FCC – CFR47, Part 15, part 2
Canada:		ICES-003
Europe		EMC Directive
Japan:		VCCI
Australia/New Zealand:		AS/NZS

Preliminary: Testing is still pending.

4	Revision 0.03

Image 4

Contents Blue Heat/Net Sync Limited Lifetime Warranty Email/Internet Telephone/FacsimileMail/Courier Preliminary Testing is still pending Class a Computing DeviceTable of Contents Installing the Blue Heat/Net Sync Configuration Manager List of Figures List of Tables Introduction Blue Heat/Net Sync Installation Overview Understanding Virtual COM PortsConnecting the Blue Heat/Net Sync to Your Network Ethernet LEDsSerial Port LEDs Connecting Serial DevicesConnections Blue Heat/Net Synchronous Clocking RS-422/V.11 ConnectionsLoopback Connectors Recommended Pinouts for V.28 RS-232 Loopback ConnectorDC Power Connector Connecting PowerPhoenix Locking Screw Terminal Connector 5VDC Activating the Special Operations Mode and Default Settings Selecting a Special OperationPower On Diagnostics LED Error CodesCRC Connect Tech SCM Serial Configuration Manager Setting a Static or Dynamic IP AddressSCM Cabling requirements Set the IP Address Using the Web Configuration Manager Set the IP Address Using the Serial Configuration ManagerConfiguration Manager BootloaderSerial Configuration Manager SCM Application  Operating System SoftwareCDS Configuration Data Space Access to CDS ParametersConfiguration Data Space CDS DescriptionSCM Serial Configuration Manager Getting Access to the SCMSCM Command Reference Brief Command ListCommand Details Boot Syntax boot mode= file= delay=Yes Myip= mip= Save File= WCM Web Configuration Manager Signing In to the Web Configuration ManagerBlue Heat/Net Sync Settings Configure Advanced Serial Settings Configure Blue Heat/Net Sync SettingsPage Configure Firmware Restore DefaultsRestore Default Settings Saving To FlashMonitoring Your Blue Heat/Net Monitor Serial Port TrafficMonitor TCP/IP Statistics Monitor Network TrafficMy Blue Heat/Net Sync My Blue Heat/Net Sync Hardware Details Installing the Blue Heat/Net Sync Configuration Manager Blue Heat/Net Sync Driver/Software Installation CDBlue Heat/Net Sync Software Installation Screen Page Page Running the Configuration Manager Device InstallationConfigure Default Blue Heat/Net Sync Add New Blue Heat/Net SyncAuto Discover Blue Heat/Net Sync Auto Discover Blue Heat/Net Sync ScreenUpgrade using WCM Web Configuration Manager Upgrade using SCM Serial Configuration ManagerHardware Information Hardware ResourcesChip Selects Chip SelectsBase Address Map InterruptsGpio Bits Direction Usage Address Range hexIusc Access Memory Map of Iusc and PLD FunctionsColdFire 5272 Bus A11 A10PLD Resource Access Address Area item Register Offset Accessed HexPLD Memory Map Table FunctionBit Serial Data transfers only IUSC-1 Offset Reg Name Valid Bit Descriptions Reset Values Hex PLD RegistersFSM CTSM1 CTSM0 PLD ID System Block Diagrams Revision Port Settings, Clock Setup and General Settings BHNPortSettingsSerial Mode smode Async MonoSync BiSync Trans-BiSync Iusc Clocking Logic Blue Heat/Net Sync Specifications Protocol Descriptions TelnetMode Equivalent Standard Electrical Typical Voltage PinoutsDB-25 Female Pinouts DB-25 Female PinoutsDB-9 Female Pinouts DB-9 Female PinoutsRack Mount Option Default Settings Network SettingsBoot Settings SCM Operation SettingsCommon Configuration Setups Static IP SetupUsing SCM Using WCMHow the Blue Heat/Net Sync Boots Up Dhcp SetupBootup Sequence Bootup SequenceFlowchart of Special Operations Mode using the reset button Asynchronous Communications TutorialSerial Line Interface Tutorial RS-232 Line InterfaceDifferential Line Interfaces RS485/RS422/V.11 DetailsBasic 4-Wire, Full Duplex Communications Multi-drop 4-Wire, Full Duplex Communications Basic Wire, Half Duplex Multi-drop ConnectionBus Contention on Differential Multi-drop Networks Termination Resistors in Differential Networks Termination Resistors in Differential Networks