Freedom9 user manual FreeStor 4020 User’s Manual

Page 56

freeStor 4020 User’s Manual

storage system. For more information, refer to “Accessing the storage system using FTP”.

To change any of the network settings:

1. Make the desired changes based on the following options:

•Workgroup name: The workgroup to which the storage system belongs on the network. In the Workgroup name text box, enter the name of the workgroup. This name can be up to 15 characters long.

•Get an IP address automatically: Instructs the freeStor 4020 to obtain an IP address from a DHCP server on the network.

•Use this IP address: Sets the IP address of the freeStor 4020 manually based on the fields below.

•IP address: The IP address of the device (if set to manual IP mode).

•Subnet mask: The subnet mask of the device (if set to manual IP mode).

•Gateway IP address: The gateway IP address of the device (if set to manual IP mode).

•Preferred DNS server: The primary DNS server’s IP address for the device to use (if set to manual IP mode).

•Alternate DNS server: The secondary DNS server’s IP address for the device to use (if set to manual IP mode).

•Enable DHCP server: Enables the DHCP server on the freeStor 4020. It is important to note that only one DHCP server should be active on the network at any one time to prevent conflicts.

•Starting IP address: The start of the IP address range to be assigned by the DHCP server.

•Ending IP address: The end of the IP address range to be assigned by the DHCP server.

2. Click “Apply”.

3. When the confirmation message appears, click “OK”.

Note: If you changed the IP address of the storage system, you must now access the Manager using the new IP address.

56

Page 55 Page 57
Image 56
Page 55 Page 57
Contents FreeStor Rev N0042000Copyright and Trademark Information Table of Contents Stopping a Backup or Recovery in Progress List of Figures 102 System Benefits and Key Features TerminologyProduct Specifications Package Contents Front Panel Rear Panel RequirementsSerial ATA hard disk LAN portInstallation and Setup Hard Drive InstallationAttaching the Hard Drive to the Tray Storage System Console Installation WelcomeReview your selections and click Next to proceed Figure To complete the installation, click Finish Figure System Setup Storage System Console10 System Initialization Screen 11 Welcome Screen Numbers, and hyphens. To proceed, click Next 15 Network Settings Page 17 Backup Calculator 18 Disk Space Distribution Web Management Interface Main Menu HomeHome Users ConnectionsTo add a new user Add User NFS Add User To remove an existing user GroupsTo edit an existing user To add a new group GroupsTo edit an existing group 10 Add GroupRemoving an existing group Shared Folders 11 Shared FoldersTo add a new shared folder 12 Add Shared Folder 14 NFS Add Shared Folder 15 Cifs Define Folder Permissions 16 NFS Define Folder Permissions To edit an existing shared folder To delete an existing shared folder Managing Backups 17 BackupsTo change the recovery CD password Deleting backupsEmail Alerts Deleting a client18 Alerts Firmware Upgrades USB Devices 19 Firmware20 USB System Settings 21 System Network Settings 22 Network FreeStor 4020 User’s Manual Disk Configuration 23 DisksFreeStor 4020 User’s Manual 24 Disk Configuration 25 Disks to Back Up 26 Disk Space Distribution Logging Out Shutting Down29 Shut Down Windows Clients Using My Computer or Windows ExplorerFile Sharing Using the Storage System Console Linux Clients Other Mac operating systems Macintosh ClientsFTP Clients System Backups with DiskSafe Express System Requirements Installing the Microsoft iSCSI Initiator Installing DiskSafe Express ISCSI Initiator WarningNET Framework License Agreement DiskSafe Express License Agreement DiskSafe Express Installation Completed Starting DiskSafe Express Activating Your License KeyActivating your license without an Internet connection Replacing your existing license Protecting Your Disks 11 DiskSafe Express Disk SelectionRecommendations 12 Add Storage System13 Storage System Selection 14 Previously Backed Up Page 16 Recover CD Password Stopping a Backup or Recovery in Progress Manually Backing Up Your DiskChanging the Backup Schedule Changing the Recovery CD Password18 Changing Recovery CD Password Dialog System Restoration with DiskSafe ExpressRecovering Files From a Backup Page Recovering a Non-System Disk or Partition Recovering a System Disk or Partition Page Page Page Removing Protection Appendix ADisk Configurations Adding Hard Disks Adding hard disks to a linear or normal RAID configuration Figure B-1 Disk Change Notification Take the desired action Removing or Replacing Hard Disks 100Responding to RAID degradation 102 Swapping hard disks Figure B-5 Disk Change Notification Page RAID FailureTransferring hard disks to a new storage system 105 Appendix BTroubleshooting Viewing the system logDisconnecting from Shared Folders Windows usersLinux users Mac usersTroubleshooting the Device 108Resolution Troubleshooting DiskSafe Express 110Problem The Status page indicates that the backup is offline Creating a Diagnostic File Using DiskSafe ExpressUsing the recovery CD Appendix CGlossary 115

4020 specifications

The Freedom9 4020 is a cutting-edge network interface device designed for a variety of applications, ranging from home use to small business environments. This versatile device is praised for its robust performance, extensive connectivity options, and user-friendly features, making it an excellent choice for those seeking a reliable network solution.

One of the standout characteristics of the Freedom9 4020 is its advanced wireless capabilities. It supports dual-band Wi-Fi, allowing users to connect to both 2.4 GHz and 5 GHz frequencies. This feature ensures optimal performance by minimizing interference and maximizing speed, making it ideal for high-bandwidth tasks such as streaming and gaming.

In terms of connectivity, the Freedom9 4020 is equipped with multiple Ethernet ports, enabling wired connections for devices that require stable and fast internet access. These ports support Power over Ethernet (PoE), which simplifies installation by eliminating the need for separate power supplies for each connected device. This is particularly beneficial in settings where devices like IP cameras or VoIP phones are deployed.

Another key feature is the device's support for advanced security protocols. The Freedom9 4020 utilizes WPA3 encryption, providing enhanced protection for connected networks. This is crucial in today’s environment, where cybersecurity threats are increasingly prevalent. The device also includes features like a built-in firewall and VPN support, enabling secure remote access for users.

The Freedom9 4020 is designed with scalability in mind. Organizations can seamlessly integrate it into existing networks and expand as their needs grow. This flexibility makes it suitable for various applications, from home automation systems to small business networks.

The user interface is intuitive, featuring a web-based management platform that allows users to monitor and control their network easily. This system provides real-time insights into network performance, making troubleshooting straightforward.

Overall, the Freedom9 4020 stands out as a versatile and powerful networking solution. With its robust wireless performance, extensive connectivity options, strong security features, and user-friendly interface, it meets the demands of modern users looking for reliability and efficiency in their network devices.
Top Page Image Contents