Freedom9 4020 user manual Using the Storage System Console

Page 65

3.In the Drive list, select the drive letter that you want to assign to the shared folder.

4.In the Folder text box, enter the following: “\\storage_system\shared_folder” where storage_system is the name or IP address of the storage system, and shared_folder is the name of the shared folder. For example, if the storage system name is Storage and the shared folder name is Photos, you would enter the following: “\\Storage\Photos”. Alternatively, you can click Browse and select the shared folder from the Microsoft Windows Network.

Note: You can use the storage system name only if that name is registered with a DNS server on your network.

5.To automatically connect to this shared folder each time you log on to Windows, select “Reconnect at logon”.

6.If you clear this option, you must repeat this procedure each time you want to access the shared folder.

7.Click “Finish”.

8.If prompted, enter your user name and password for accessing this shared folder, and then click “OK”.

Note: If the user name and password for accessing the shared folder are the same as your Windows user name and password, you will not be prompted to provide a user name and password to access the shared folder.

In addition, once you provide your user name and password for accessing one shared folder, you are not prompted to provide it again when you access other shared folders to which you have access rights.

If the guest user has access to this shared folder, you can use guest as both the user name and password.

You can now access the shared folder from My Computer or Windows Explorer.

Using the Storage System Console

To access a shared folder using the Storage System Console:

1.Install the Storage System Console (as described in Section 2.2).

2.Click Start Æ Programs Æ Storage System Console.

3.As soon as you start the Storage System Console, it automatically scans the network for

65

Page 64 Page 66
Image 65
Page 64 Page 66
Contents Rev N0042000 FreeStorCopyright and Trademark Information Table of Contents Stopping a Backup or Recovery in Progress List of Figures 102 Terminology System Benefits and Key FeaturesProduct Specifications Package Contents Front Panel Requirements Rear PanelLAN port Serial ATA hard diskHard Drive Installation Installation and SetupAttaching the Hard Drive to the Tray Welcome Storage System Console InstallationReview your selections and click Next to proceed Figure To complete the installation, click Finish Figure Storage System Console System Setup10 System Initialization Screen 11 Welcome Screen Numbers, and hyphens. To proceed, click Next 15 Network Settings Page 17 Backup Calculator 18 Disk Space Distribution Web Management Interface Home Main MenuHome Connections UsersTo add a new user Add User NFS Add User To remove an existing user GroupsTo edit an existing user Groups To add a new group10 Add Group To edit an existing groupRemoving an existing group 11 Shared Folders Shared FoldersTo add a new shared folder 12 Add Shared Folder 14 NFS Add Shared Folder 15 Cifs Define Folder Permissions 16 NFS Define Folder Permissions To edit an existing shared folder To delete an existing shared folder 17 Backups Managing BackupsDeleting backups To change the recovery CD passwordDeleting a client Email Alerts18 Alerts Firmware Upgrades 19 Firmware USB Devices20 USB System Settings 21 System Network Settings 22 Network FreeStor 4020 User’s Manual 23 Disks Disk ConfigurationFreeStor 4020 User’s Manual 24 Disk Configuration 25 Disks to Back Up 26 Disk Space Distribution Shutting Down Logging Out29 Shut Down Windows Clients Using My Computer or Windows ExplorerFile Sharing Using the Storage System Console Linux Clients Other Mac operating systems Macintosh ClientsFTP Clients System Backups with DiskSafe Express System Requirements Installing the Microsoft iSCSI Initiator ISCSI Initiator Warning Installing DiskSafe ExpressNET Framework License Agreement DiskSafe Express License Agreement DiskSafe Express Installation Completed Activating Your License Key Starting DiskSafe ExpressActivating your license without an Internet connection Replacing your existing license 11 DiskSafe Express Disk Selection Protecting Your Disks12 Add Storage System Recommendations13 Storage System Selection 14 Previously Backed Up Page 16 Recover CD Password Manually Backing Up Your Disk Stopping a Backup or Recovery in ProgressChanging the Recovery CD Password Changing the Backup ScheduleSystem Restoration with DiskSafe Express 18 Changing Recovery CD Password DialogRecovering Files From a Backup Page Recovering a Non-System Disk or Partition Recovering a System Disk or Partition Page Page Page Removing Protection Appendix ADisk Configurations Adding Hard Disks Adding hard disks to a linear or normal RAID configuration Figure B-1 Disk Change Notification Take the desired action 100 Removing or Replacing Hard DisksResponding to RAID degradation 102 Figure B-5 Disk Change Notification Page RAID Failure Swapping hard disksTransferring hard disks to a new storage system 105 Viewing the system log Appendix BTroubleshootingWindows users Disconnecting from Shared FoldersLinux users Mac users108 Troubleshooting the DeviceResolution 110 Troubleshooting DiskSafe ExpressProblem The Status page indicates that the backup is offline Using DiskSafe Express Creating a Diagnostic FileUsing the recovery CD Appendix CGlossary 115

4020 specifications

The Freedom9 4020 is a cutting-edge network interface device designed for a variety of applications, ranging from home use to small business environments. This versatile device is praised for its robust performance, extensive connectivity options, and user-friendly features, making it an excellent choice for those seeking a reliable network solution.

One of the standout characteristics of the Freedom9 4020 is its advanced wireless capabilities. It supports dual-band Wi-Fi, allowing users to connect to both 2.4 GHz and 5 GHz frequencies. This feature ensures optimal performance by minimizing interference and maximizing speed, making it ideal for high-bandwidth tasks such as streaming and gaming.

In terms of connectivity, the Freedom9 4020 is equipped with multiple Ethernet ports, enabling wired connections for devices that require stable and fast internet access. These ports support Power over Ethernet (PoE), which simplifies installation by eliminating the need for separate power supplies for each connected device. This is particularly beneficial in settings where devices like IP cameras or VoIP phones are deployed.

Another key feature is the device's support for advanced security protocols. The Freedom9 4020 utilizes WPA3 encryption, providing enhanced protection for connected networks. This is crucial in today’s environment, where cybersecurity threats are increasingly prevalent. The device also includes features like a built-in firewall and VPN support, enabling secure remote access for users.

The Freedom9 4020 is designed with scalability in mind. Organizations can seamlessly integrate it into existing networks and expand as their needs grow. This flexibility makes it suitable for various applications, from home automation systems to small business networks.

The user interface is intuitive, featuring a web-based management platform that allows users to monitor and control their network easily. This system provides real-time insights into network performance, making troubleshooting straightforward.

Overall, the Freedom9 4020 stands out as a versatile and powerful networking solution. With its robust wireless performance, extensive connectivity options, strong security features, and user-friendly interface, it meets the demands of modern users looking for reliability and efficiency in their network devices.
Top Page Image Contents