Asante Technologies 3500 Series user manual System Reset Configuration, Resetting the Switch

Page 38

Performing a Software Upgrade

Use the following procedure to upgrade the switch’s software through its serial (console) port:

1.In the Image File Download Configuration Menu, type x to access the X/Y/Z Modem Image File Downloading Menu.

2.Type x, y or z to select the corresponding modem protocol.

Note: For information about these protocols, see the manual for your communications software.

3.Type c to select the console baud rate. The Baud Rate Setting Menu appears. The maximum baud rate currently supported is 57,600 bps.

4.Select one of the options in the above screen to select the required baud rate, and confirm it by typing y.

Note: The baud rate default for console management is 9600 bps; in most cases the default will match the rate for the connected terminal. If you change the baud rate for the console port, the screen will display garbled data unless the connected terminal is set to the same rate.

5.Type a to select the Destination Bank.

6.To download the image file, use any serial communications software such as Procomm Plus, HyperTerminal, ZTerm, etc. For file transfer instructions, follow the instruction manual of the serial communications software.

Note: The terminal on which the serial communications software is running must have the same baud rate as switch’s console. The connection from the terminal to the switch console port must be an RS232C straight-through cable.

7.Type d to download to the selected destination bank or b to download and reset.

8.After performing a successful download, type q to return to the previous menu.

3.15System Reset Configuration

The System Reset Configuration Menu allows you to reset the switch by performing a “warm” reboot. It also allows you to schedule a reset up to 24 hours in advance.

IntraCore 3524 System Reset

Configuration Menu

Bank

1

Image Version/Date:

1.10/Dec

05 2001

13:54:06

Bank

2

Image Version/Date:

1.10/Dec

05 2001

13:54:06 (Running)

Reset Status: Stop

Reset Type: Normal

Reset Countdown: 1 sec.

Load Mode: Local

Boot Bank: 2

<Cmd> <Description>

sSchedule Reset Time

c Cancel Reset

r Reset Switch

a Toggle Boot Bank

d Reset Switch to Factory Default

i Reset Switch to Factory Default except IP and Bootstrap

q Return to previous menu

Command>

3.15.1 Resetting the Switch

To reset the switch, use the following procedure:

1.Open the System Reset Menu by typing r in the Configuration Menu.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents IntraCore 3500 Series Quick Start Guide Gigabit Ethernet Switches User’s Manual IntraCore 3500 SeriesTable of Contents Page Package Contents IntroductionLEDs 1 IC3524 Models2 IC3548-2GT 4810/100Front and Back Panel Descriptions #49Management and Configuration Snmp Management Console InterfaceWeb-Based Interface Safety Overview Hardware Installation and SetupInstallation Overview Power Requirements Installation into an Equipment RackRecommended Installation Tools Environmental RequirementsEquipment Rack Guidelines Installing a GbicGbic Interfaces Removing a Gbic Installing Optional Hardware ModulesConnecting Power Gbic Care and HandlingConnecting to the Network 1 10/100BaseT Ports Cabling ProceduresConnecting to a Console SetupGigabit Ethernet Ports Cabling Procedures Connecting Via Telnet Changing the PasswordConnecting Via the Web Browser IP Assignment Snmp ManagementUsing the Stacking Feature IC3524 only Toggle Stacking Enable/Disable Logging ConfigurationAccessing a Submenu Exiting a Submenu Configuration MenuGeneral Information System Administration Configuration Changing System Administration InfoChanging System IP Information System IP ConfigurationBootstrap Configuration Snmp Configuration Changing Community StringsDeleting a Trap Receiver Enabling Authentication TrapsAdding or Updating a Trap Receiver Port Configuration Basic Port Configuration Menu appearsConfiguring Auto-Negotiation Enabling or Disabling a PortToggling Port Link Speed Configuring a Port ManuallyConfiguring 1000BaseX Ports Toggling Half to Full DuplexEnabling or Disabling 802.3x Flow Control Advanced Port ConfigurationSetting Port Class of Service Setting Port Default Priority Global Port ConfigurationUnicast Forwarding Database Configuration Displaying the Forwarding DatabaseSetting the MAC Address Age-Out Time Searching for a MAC AddressVlan Management Port Mirroring ConfigurationSecurity Management IP Multicast Traffic ManagementImage Downloading through Tftp File Up/Downloading ConfigurationSetting the Monitor Port Serial Downloading Configuration Performing a Software Upgrade at RuntimePerforming a Software Upgrade System Reset ConfigurationResetting the Switch Scheduling a System Reset System LogUser Interface Configuration Clearing the System LogSetting Console Idle Time-out Period Setting Telnet Idle Time-out PeriodEnabling or Disabling the Web Server Changing the PasswordSystem Utility Viewing Statistics Spanning Tree Protocol Configuring Spanning Tree ParametersAdvanced Management Enabling and Disabling STPSpanning Tree Port Configuration Setting Port Priority and Path CostRmon Management Snmp and Rmon ManagementDuplicated IP Detection and Trap Enabling and Disabling Duplicated IP Trap Enabling and Disabling Station Movement TrapEnabling and Disabling Duplicated IP Detection Viewing a List of Duplicated IP AddressesConfiguring Port Security Configuring Port New Node Detection TrapSetting the Intruder Trap Configuring Port Lock and Intruder LockConfiguring Security Level 2 or Level Other Vlan Features of the switch Vlan Specifications for the IntraCore 3500 SeriesResetting Security to Defaults Inserting/Modifying a Port Trusted MAC AddressConfiguring Static Vlan Groups Kkxxxxxx KxxxxxxxAdvanced Static Vlan Configuration Specifying Tagging or No Tagging for a Port Configuring Vlan Port AttributesSetting the Port Vlan ID Displaying a Vlan Port Summary Configuring Port Receive Frame TypeDisplaying a Summary of Vlan Groups Adding and Deleting VLANs from the PortResetting Vlan Configuration to Defaults Multicast AddressesEnabling and Disabling Igmp Snooping Configuring IP Multicast Traffic ManagementIgmp Snooping Displaying a Summary of Group AddressesInserting a Multicast Group Address IP Multicast Forwarding Database ConfigurationAdding Ports to the Selected Address Removing a Multicast Group Address To remove an addressAccessing with a Web Browser Web-Based ManagementFront Panel Button Genl Info General Information ButtonStatistics Button Port Config Port Configuration Button Span Tree Spanning Tree Button Snmp Button Addr Address Table ButtonVlan Button Port Configuration Adding and Deleting Port Members Vlan ConfigurationCreating or Modifying a Vlan Page Security Button Duplicate IP Button Snmp Protocol Snmp ManagementSnmp Management Operations Name Space Path Community Name and SecurityMIB Tree MIB Groups SupportedPage Port-Based VLANs Switching ConceptsVLANs Vlan ID and Tagged FramesSpanning Tree Parameters Port Vlan IDHow It Works Full Duplex Forward DelayFull Duplex, Flow Control and Auto-negotiation Port PriorityFlow Control Auto-NegotiationAppendix A. Troubleshooting Problem Possible SolutionsSpecifications Appendix B. Features and SpecificationsFeatures Environmental Range Physical CharacteristicsTechnical Support and Warranty Standards ComplianceIntraCare Warranty Statement Appendix C. FCC Compliance and Warranty StatementsFCC Compliance Statement Important Safety Instructions Page Pin Number Signal Name Appendix D. Console Port Pin OutsAppendix E. Online Warranty Registration Image Banks Appendix F. BootP ConfigurationBootstrap Configuration Loading Software Locally
Top Page Image Contents