Asante Technologies 3500 Series user manual Spanning Tree Port Configuration

Page 45

IntraCore 3524 Spanning Tree Configuration Menu
STP Status:	Enabled
Bridge ID:	8000	00:00:94:CC:C7:37
Designated Root:	4000	00:00:94:AA:64:31
Root Port:	Unit: 2		Port: 1
Root Path Cost:	100
Addr Ageout Time: 300
Hello Time:	3 Sec.		Bridge Hello Time:	2 Sec.
Maximum Age:	20 Sec.		Bridge Maximum Age:	20 Sec.
Forward Delay:	15 Sec.		Bridge Forward Delay:	15 Sec.

<Cmd> <Description>

tToggle STP Enable/Disable

i Set Bridge Priority

h Set Bridge Hello Time

a Set Bridge Maximum Age

d Set Bridge Forward Delay

p Spanning Tree Port Configuration

q Return to previous menu

Command>

4.1.3 Spanning Tree Port Configuration

To set the Port Priority and Port Path Cost values for STP, access the Spanning Tree Port Configuration Menu shown below by typing p in the Spanning Tree Configuration Menu.


IntraCore	3524 Spanning Tree Port Configuration Menu		Unit: [1] Port: [01]
Port Speed:		10 Mbps
Port Status:		Enabled
Port State:		Forwarding
Port MAC Address:		00:00:94:CC:C7:6D
Port Priority:		0x80
Port Path Cost:		100
<Cmd>	<Description>
i	Set Port Priority
c	Set Port Path Cost
q	Return to previous menu
o	Display Stacking port cost (debug menu)

Command>

Select U)nit Nex)t unit Prev) unit S)elect port N)ext port P)rev port

Setting Port Priority and Path Cost

Use the following procedure to set the STP Port Priority and Path Cost values:

1.Access the Spanning Tree Port Configuration Menu by typing p in the Spanning Tree Configuration Menu.

2.Use the s, n and p commands to select the port you want to configure.

3.Type i to set the Port Priority. Type c to set the Port Path Cost.

4.Enter a value for the setting you are making. See Chapter 7 for more information.

5.Press Enter.

The new Port Priority or Port Path Cost is displayed in the Spanning Tree Port Configuration Menu.

45

Image 45

Contents IntraCore 3500 Series Quick Start Guide IntraCore 3500 Series Gigabit Ethernet Switches User’s ManualTable of Contents Page Introduction Package Contents1 IC3524 Models LEDs4810/100 2 IC3548-2GT#49 Front and Back Panel DescriptionsManagement and Configuration Console Interface Web-Based InterfaceSnmp Management Hardware Installation and Setup Installation OverviewSafety Overview Recommended Installation Tools Installation into an Equipment RackPower Requirements Environmental RequirementsInstalling a Gbic Gbic InterfacesEquipment Rack Guidelines Connecting Power Installing Optional Hardware ModulesRemoving a Gbic Gbic Care and Handling1 10/100BaseT Ports Cabling Procedures Connecting to the NetworkSetup Gigabit Ethernet Ports Cabling ProceduresConnecting to a Console Changing the Password Connecting Via the Web BrowserConnecting Via Telnet Snmp Management IP AssignmentUsing the Stacking Feature IC3524 only Toggle Stacking Enable/Disable Configuration Accessing a SubmenuLogging Configuration Menu General InformationExiting a Submenu Changing System Administration Info System Administration ConfigurationSystem IP Configuration Bootstrap ConfigurationChanging System IP Information Changing Community Strings Snmp ConfigurationEnabling Authentication Traps Adding or Updating a Trap ReceiverDeleting a Trap Receiver Basic Port Configuration Menu appears Port ConfigurationEnabling or Disabling a Port Configuring Auto-NegotiationConfiguring 1000BaseX Ports Configuring a Port ManuallyToggling Port Link Speed Toggling Half to Full DuplexAdvanced Port Configuration Setting Port Class of ServiceEnabling or Disabling 802.3x Flow Control Global Port Configuration Setting Port Default PriorityDisplaying the Forwarding Database Unicast Forwarding Database ConfigurationSearching for a MAC Address Setting the MAC Address Age-Out TimeSecurity Management Port Mirroring ConfigurationVlan Management IP Multicast Traffic ManagementFile Up/Downloading Configuration Setting the Monitor PortImage Downloading through Tftp Performing a Software Upgrade at Runtime Serial Downloading ConfigurationSystem Reset Configuration Resetting the SwitchPerforming a Software Upgrade System Log Scheduling a System ResetClearing the System Log User Interface ConfigurationSetting Telnet Idle Time-out Period Setting Console Idle Time-out PeriodChanging the Password System UtilityEnabling or Disabling the Web Server Viewing Statistics Advanced Management Configuring Spanning Tree ParametersSpanning Tree Protocol Enabling and Disabling STPSetting Port Priority and Path Cost Spanning Tree Port ConfigurationSnmp and Rmon Management Duplicated IP Detection and TrapRmon Management Enabling and Disabling Duplicated IP Detection Enabling and Disabling Station Movement TrapEnabling and Disabling Duplicated IP Trap Viewing a List of Duplicated IP AddressesConfiguring Port New Node Detection Trap Configuring Port SecurityConfiguring Port Lock and Intruder Lock Configuring Security Level 2 or LevelSetting the Intruder Trap Resetting Security to Defaults Vlan Specifications for the IntraCore 3500 SeriesOther Vlan Features of the switch Inserting/Modifying a Port Trusted MAC AddressKkxxxxxx Kxxxxxxx Configuring Static Vlan GroupsAdvanced Static Vlan Configuration Configuring Vlan Port Attributes Setting the Port Vlan IDSpecifying Tagging or No Tagging for a Port Displaying a Summary of Vlan Groups Configuring Port Receive Frame TypeDisplaying a Vlan Port Summary Adding and Deleting VLANs from the PortMulticast Addresses Resetting Vlan Configuration to DefaultsIgmp Snooping Configuring IP Multicast Traffic ManagementEnabling and Disabling Igmp Snooping Displaying a Summary of Group AddressesAdding Ports to the Selected Address IP Multicast Forwarding Database ConfigurationInserting a Multicast Group Address Removing a Multicast Group Address To remove an addressWeb-Based Management Accessing with a Web BrowserGenl Info General Information Button Front Panel ButtonStatistics Button Port Config Port Configuration Button Span Tree Spanning Tree Button Addr Address Table Button Snmp ButtonVlan Button Port Configuration Vlan Configuration Creating or Modifying a VlanAdding and Deleting Port Members Page Security Button Duplicate IP Button Snmp Management Snmp Management OperationsSnmp Protocol MIB Tree Community Name and SecurityName Space Path MIB Groups SupportedPage VLANs Switching ConceptsPort-Based VLANs Vlan ID and Tagged FramesPort Vlan ID How It WorksSpanning Tree Parameters Full Duplex, Flow Control and Auto-negotiation Forward DelayFull Duplex Port PriorityAuto-Negotiation Flow ControlProblem Possible Solutions Appendix A. TroubleshootingAppendix B. Features and Specifications FeaturesSpecifications Technical Support and Warranty Physical CharacteristicsEnvironmental Range Standards ComplianceAppendix C. FCC Compliance and Warranty Statements FCC Compliance Statement Important Safety InstructionsIntraCare Warranty Statement Page Appendix D. Console Port Pin Outs Pin Number Signal NameAppendix E. Online Warranty Registration Bootstrap Configuration Appendix F. BootP ConfigurationImage Banks Loading Software Locally