Motorola BLE100 operation manual Amplifier Setup

Page 31

3-10	Amplifier Setup

8Check the amplifier output tilt by measuring the high band- and low band-edge carriers.

High = channel 116 (745.25 MHz), channel 136 (865.25 MHz), or channel 158 (997.25 MHz)

Low = channel 2 (55.25 MHz) or channel 3 (61.25 MHz)

If the tilt is less than required, install a higher value input equalizer.

If the tilt is greater than required, install a lower value input equalizer.

If the high value equalizer provides too much tilt and the low value equalizer provides too little tilt, use the lower value equalizer. Under-equalization is preferred to over-equalization.

If the amplifier was set up using an SCS-*, the JXP input pad must be increased or decreased by the amount of change made in the SCS-* value. Therefore, to maintain a proper gain level, it is necessary to adjust the input pad value as follows:

For each increase in SCS value, decrease the input pad by 1 dB.

For each decrease in SCS value, increase the input pad by 1 dB.

If you replace an SFE with an SCS, reduce the value of the input pad by the value of the SCS.

9Measure the output level at the highest frequency.

It should be within 1 dB of the system design level. If it is not, you must adjust the mid-stage pad (JXP MID) accordingly. Refer to Section 6, “Operating Tips,” for mid-stage padding information and recommendations.

BLE100 Installation and Operation Manual

Image 31

Contents Installation BLE100 Special Symbols That Might Appear on the Equipment Page Contents Operating Tips Bench TestingInstallation SpecificationsTables Torque Specifications Abbreviations and AcronymsAppendix B BLE100 closed IntroductionBLE BLE100 openRelated Documentation Using This ManualDocument Conventions Motorola Online http//businessonline.motorola.com If You Need HelpCalling for Repairs BLE100 base with electronics module OverviewBLE100 ordering matrix Ordering MatrixBLE-HSG/15 housing and dimensions HousingGaskets Housing gasketsPort Locations Housing portsBLE100 power supply Power SupplyForward Path BLE100 block diagramReturn Path Model Description Function Ingress Control SwitchOptions and Accessories BLE100 options and accessoriesSRE SFE-100SCS RCB JXP Field Practice Amplifier SetupProper Handling Procedures Bench SetupBefore You Begin Forward Path AlignmentExample Starline Cable EqualizersSlope SFE-100 Starline Forward Equalizers SFE-100Equalizer slope versus cable Frequency Cable slope in dB Starline Cable SimulatorsStarline Cable Simulators Flatness Control Input and Midstage PadsFrequency versus cable slope Bode Equalization Directional Coupler Test PointsLDR/9/1G component layout top-left, bottom-right Manual Gain Control Temperature Gain ReserveGain reserve versus ambient temperature Amplifier Level ControlAmplifier Setup Automatic Drive Unit/QAM Automatic Drive Unit ADU/QADU Pads and Levels Return Path AlignmentAlignment Procedure Powering and Surge Protection Before You Begin Bench TestingMeasuring Forward Gain Test Equipment and ConnectionsTest equipment connections for bench sweeping Example Completing the Test Procedures Testing Return Gain and ResponseAerial Installation InstallationCenter-conductor pin length Torque sequence J1 position DescriptionPedestal Installation Using Amplifiers in Lower Gain Systems Using Amplifiers in Lower Frequency SystemsOperating Tips Forward Amplifier SpecificationsSpecification Model BLE100SReturn Amplifier AC CurrentADU Automatic Drive Unit Torque Fastener Screw Wrench In-lbs Torque SpecificationsSize Abbreviations and Acronyms Visit our website at 527548-001 04/06

BLE100 specifications

The Motorola BLE100 is an innovative device designed for efficiency and reliability in the realm of Bluetooth Low Energy (BLE) technology. As a compact and multifunctional solution, it caters to diverse applications, from cost-effective asset tracking to improving smart home environments. The BLE100 stands out for its practicality, making it ideal for both personal and commercial use.

One of the standout features of the Motorola BLE100 is its low power consumption. Leveraging Bluetooth Low Energy technology, the device can operate for extended periods without frequent battery replacements—ideal for remote monitoring applications where long-lasting performance is crucial. This characteristic ensures that users can rely on the BLE100 for day-to-day operations without the hassle of constant recharging.

In terms of connectivity, the BLE100 boasts seamless and stable connections over considerable distances. With a range of up to 100 meters in open environments, the device excels in maintaining reliable communication even in challenging conditions. Its compatibility with a wide array of Bluetooth-enabled devices ensures versatile usability, allowing users to integrate the BLE100 into existing systems with ease.

The Motorola BLE100 also prioritizes user-friendly design. The device is lightweight and compact, ensuring ease of installation and portability. Its robust build makes it resilient against environmental factors, while its sleek design enhances its aesthetic appeal. Moreover, straightforward setup processes and user interfaces facilitate quick deployment for various applications.

Another notable characteristic of the BLE100 is its advanced security features. With built-in encryption and pairing mechanisms, users can safeguard their data and communication. This is particularly vital in applications requiring confidential or sensitive information transfer.

The device supports various protocols and adheres to international standards, which ensures versatility and compatibility in multiple applications. Whether it's intelligent home systems seeking efficient device interaction or logistics needing simple asset tracking solutions, the Motorola BLE100 meets diverse needs.

In conclusion, the Motorola BLE100 is a powerful device that marries efficiency, functionality, and security. Its low power usage, reliable connectivity, user-friendly design, and robust features make it a top choice for anyone looking to enhance their Bluetooth Low Energy applications. With the BLE100, users can explore a wide range of possibilities, from smart technology integration to simplified monitoring solutions, all designed to optimize performance while maintaining a user-centric approach.