Motorola BLE100 operation manual Powering and Surge Protection

Page 35

3-14	Amplifier Setup

Return levels used for alignment are not necessarily operational system levels. These levels vary from system to system due to differences in equipment, architectures and design philosophies. For an in-depth analysis and discussion of the return path, refer to Motorola reference guide Return Path Level Selection, Setup and Alignment Procedure.

Powering and Surge Protection

In conventional applications, the BLE100s are powered through the input port.

CAUTION!

To avoid damage to the hybrids, it is recommended that you remove the input pad (JXP-IN) before you apply power to the BLE100.

A20-ampere, blade-type fuse is furnished in the amplifier module and provides overcurrent protection for AC power applied to the input. You can power the BLE100 from the output without passing power through to the input port. To block power from the input port, remove the power-block jumper illustrated in Figure 2-8.

WARNING!

To avoid possible injury to personnel or damage to the equipment, remove 60/90 volt ac power from the system before you remove any components from the housing.

The BLE100 is shipped from the factory configured for 38 through 90 VAC powering as described in Section 2, “Overview”. To configure the BLE100 for 55 VAC through 90 VAC operation:

1Remove the electronics chassis from the housing.

2Remove the power-supply cover.

3Move the LO/HI selector (jumper J1 on the power-supply board) from the LO to HI position. Figure 2-6 illustrates the jumper location.

4Re-install the power-supply cover and torque the screws to 10 to 12 in-lbs.

5Re-install the electronics chassis in the housing and torque the hold-down bolts to 18 to 22 in-lbs.

BLE100 Installation and Operation Manual

Image 35

Contents Installation BLE100 Special Symbols That Might Appear on the Equipment Page Contents Operating Tips Bench TestingInstallation SpecificationsAppendix B Torque Specifications Abbreviations and AcronymsTables BLE100 closed IntroductionBLE BLE100 openDocument Conventions Using This ManualRelated Documentation Motorola Online http//businessonline.motorola.com If You Need HelpCalling for Repairs BLE100 base with electronics module OverviewBLE100 ordering matrix Ordering MatrixBLE-HSG/15 housing and dimensions HousingGaskets Housing gasketsPort Locations Housing portsBLE100 power supply Power SupplyReturn Path BLE100 block diagramForward Path Model Description Function Ingress Control SwitchOptions and Accessories BLE100 options and accessoriesSCS SFE-100SRE RCB JXP Field Practice Amplifier SetupProper Handling Procedures Bench SetupBefore You Begin Forward Path AlignmentExample Starline Cable EqualizersSlope SFE-100 Starline Forward Equalizers SFE-100Equalizer slope versus cable Starline Cable Simulators Starline Cable SimulatorsFrequency Cable slope in dB Frequency versus cable slope Input and Midstage PadsFlatness Control LDR/9/1G component layout top-left, bottom-right Directional Coupler Test PointsBode Equalization Manual Gain Control Temperature Gain ReserveGain reserve versus ambient temperature Amplifier Level ControlAmplifier Setup Automatic Drive Unit/QAM Automatic Drive Unit ADU/QADU Pads and Levels Return Path AlignmentAlignment Procedure Powering and Surge Protection Before You Begin Bench TestingTest equipment connections for bench sweeping Test Equipment and ConnectionsMeasuring Forward Gain Example Completing the Test Procedures Testing Return Gain and ResponseCenter-conductor pin length InstallationAerial Installation Torque sequence J1 position DescriptionPedestal Installation Operating Tips Using Amplifiers in Lower Frequency SystemsUsing Amplifiers in Lower Gain Systems Forward Amplifier SpecificationsSpecification Model BLE100SADU Automatic Drive Unit AC CurrentReturn Amplifier Size Torque SpecificationsTorque Fastener Screw Wrench In-lbs Abbreviations and Acronyms Visit our website at 527548-001 04/06

BLE100 specifications

The Motorola BLE100 is an innovative device designed for efficiency and reliability in the realm of Bluetooth Low Energy (BLE) technology. As a compact and multifunctional solution, it caters to diverse applications, from cost-effective asset tracking to improving smart home environments. The BLE100 stands out for its practicality, making it ideal for both personal and commercial use.

One of the standout features of the Motorola BLE100 is its low power consumption. Leveraging Bluetooth Low Energy technology, the device can operate for extended periods without frequent battery replacements—ideal for remote monitoring applications where long-lasting performance is crucial. This characteristic ensures that users can rely on the BLE100 for day-to-day operations without the hassle of constant recharging.

In terms of connectivity, the BLE100 boasts seamless and stable connections over considerable distances. With a range of up to 100 meters in open environments, the device excels in maintaining reliable communication even in challenging conditions. Its compatibility with a wide array of Bluetooth-enabled devices ensures versatile usability, allowing users to integrate the BLE100 into existing systems with ease.

The Motorola BLE100 also prioritizes user-friendly design. The device is lightweight and compact, ensuring ease of installation and portability. Its robust build makes it resilient against environmental factors, while its sleek design enhances its aesthetic appeal. Moreover, straightforward setup processes and user interfaces facilitate quick deployment for various applications.

Another notable characteristic of the BLE100 is its advanced security features. With built-in encryption and pairing mechanisms, users can safeguard their data and communication. This is particularly vital in applications requiring confidential or sensitive information transfer.

The device supports various protocols and adheres to international standards, which ensures versatility and compatibility in multiple applications. Whether it's intelligent home systems seeking efficient device interaction or logistics needing simple asset tracking solutions, the Motorola BLE100 meets diverse needs.

In conclusion, the Motorola BLE100 is a powerful device that marries efficiency, functionality, and security. Its low power usage, reliable connectivity, user-friendly design, and robust features make it a top choice for anyone looking to enhance their Bluetooth Low Energy applications. With the BLE100, users can explore a wide range of possibilities, from smart technology integration to simplified monitoring solutions, all designed to optimize performance while maintaining a user-centric approach.