Motorola BLE100 Amplifier Setup, Proper Handling Procedures, Field Practice, Bench Setup

Page 22

Section 3

Amplifier Setup

This section provides instructions on how to properly handle and configure the BLE100. It also describes the proper forward and return path alignment procedures. It is recommended that you read this entire section before you install the BLE100.

Proper Handling Procedures

The following information is useful in reducing GaAs RF amplifier failures caused by Electrostatic Discharge (ESD) or Electrical Over Stress (EOS).

Many electronic components are vulnerable to ESD and EOS. Improper handling during service and installation can subject the BLE100 to performance degradation or failure. All closed operational units are equally protected. Compliance with proper handling procedures can significantly reduce ESD and EOS related failures.

To avoid excessive signal level which causes EOS, follow the procedures listed below:

Field Practice

Proper field procedures include:

Installing the system design value forward equalizer and a high value (20 dB or above) input pad before you install or remove the electronics chassis or activate the system. This significantly reduces RF signal level and avoids possible EOS which can damage the hybrids.

Leaving the input pad location open if a high value pad is not available. A more accurate forward input test point reading is achieved with a high value pad installed.

Avoiding handling of the hybrids. If you need to remove or install the hybrids, follow proper ESD grounding practices as stated under Bench Setup.

Bench Setup

Proper bench handling practices include:

Grounding of the test bench with ESD matting on the work surface and wearing a wrist strap connected to a continuous ground monitor checker. These practices are particularly important when handling hybrids.

Terminating all unused ports with a 75-ohm load.

Securing all electronics module cover screws or removing the cover completely. Loose screws can cause the BLE100 to oscillate and degrade performance.

BLE100 Installation and Operation Manual

Image 22

Contents Installation BLE100 Special Symbols That Might Appear on the Equipment Page Contents Specifications Bench TestingInstallation Operating TipsTables Torque Specifications Abbreviations and AcronymsAppendix B Introduction BLE100 closedBLE100 open BLERelated Documentation Using This ManualDocument Conventions If You Need Help Motorola Online http//businessonline.motorola.comCalling for Repairs Overview BLE100 base with electronics moduleOrdering Matrix BLE100 ordering matrixHousing BLE-HSG/15 housing and dimensionsHousing gaskets GasketsHousing ports Port LocationsPower Supply BLE100 power supplyForward Path BLE100 block diagramReturn Path BLE100 options and accessories Ingress Control SwitchOptions and Accessories Model Description FunctionSRE SFE-100SCS RCB JXP Bench Setup Amplifier SetupProper Handling Procedures Field PracticeForward Path Alignment Before You BeginStarline Cable Equalizers ExampleStarline Forward Equalizers SFE-100 Slope SFE-100Equalizer slope versus cable Frequency Cable slope in dB Starline Cable SimulatorsStarline Cable Simulators Flatness Control Input and Midstage PadsFrequency versus cable slope Bode Equalization Directional Coupler Test PointsLDR/9/1G component layout top-left, bottom-right Amplifier Level Control Temperature Gain ReserveGain reserve versus ambient temperature Manual Gain ControlAmplifier Setup Automatic Drive Unit/QAM Automatic Drive Unit Return Path Alignment ADU/QADU Pads and LevelsAlignment Procedure Powering and Surge Protection Bench Testing Before You BeginMeasuring Forward Gain Test Equipment and ConnectionsTest equipment connections for bench sweeping Example Testing Return Gain and Response Completing the Test ProceduresAerial Installation InstallationCenter-conductor pin length J1 position Description Torque sequencePedestal Installation Using Amplifiers in Lower Gain Systems Using Amplifiers in Lower Frequency SystemsOperating Tips Model BLE100S SpecificationsSpecification Forward AmplifierReturn Amplifier AC CurrentADU Automatic Drive Unit Torque Fastener Screw Wrench In-lbs Torque SpecificationsSize Abbreviations and Acronyms Visit our website at 527548-001 04/06

BLE100 specifications

The Motorola BLE100 is an innovative device designed for efficiency and reliability in the realm of Bluetooth Low Energy (BLE) technology. As a compact and multifunctional solution, it caters to diverse applications, from cost-effective asset tracking to improving smart home environments. The BLE100 stands out for its practicality, making it ideal for both personal and commercial use.

One of the standout features of the Motorola BLE100 is its low power consumption. Leveraging Bluetooth Low Energy technology, the device can operate for extended periods without frequent battery replacements—ideal for remote monitoring applications where long-lasting performance is crucial. This characteristic ensures that users can rely on the BLE100 for day-to-day operations without the hassle of constant recharging.

In terms of connectivity, the BLE100 boasts seamless and stable connections over considerable distances. With a range of up to 100 meters in open environments, the device excels in maintaining reliable communication even in challenging conditions. Its compatibility with a wide array of Bluetooth-enabled devices ensures versatile usability, allowing users to integrate the BLE100 into existing systems with ease.

The Motorola BLE100 also prioritizes user-friendly design. The device is lightweight and compact, ensuring ease of installation and portability. Its robust build makes it resilient against environmental factors, while its sleek design enhances its aesthetic appeal. Moreover, straightforward setup processes and user interfaces facilitate quick deployment for various applications.

Another notable characteristic of the BLE100 is its advanced security features. With built-in encryption and pairing mechanisms, users can safeguard their data and communication. This is particularly vital in applications requiring confidential or sensitive information transfer.

The device supports various protocols and adheres to international standards, which ensures versatility and compatibility in multiple applications. Whether it's intelligent home systems seeking efficient device interaction or logistics needing simple asset tracking solutions, the Motorola BLE100 meets diverse needs.

In conclusion, the Motorola BLE100 is a powerful device that marries efficiency, functionality, and security. Its low power usage, reliable connectivity, user-friendly design, and robust features make it a top choice for anyone looking to enhance their Bluetooth Low Energy applications. With the BLE100, users can explore a wide range of possibilities, from smart technology integration to simplified monitoring solutions, all designed to optimize performance while maintaining a user-centric approach.