ADVANCED FUNCTIONS
With up to seven main channels, plus a subwoofer, imaging becomes both more critical and more complex. The goal is to ensure that each channel is heard at the listening position with equal loudness.
EzSet/EQ calibration can handle this critical task for you, simply and automatically. However, the AVR’s Level Adjust menu allows you to calibrate the levels manually, either using the system’s test tone or while playing source material.
1.Make sure all speakers have been placed and connected correctly.
2.Adjust the number of speakers, crossover, distance and sub mode for each speaker in your system, as described in Step Three.
3.Measure the channel levels in one of these ways, and adjust the channel levels using the Level Adjust menu:
a)Preferably, use a handheld SPL meter set to the
b)By ear. Adjust the levels so that all channels sound equally loud.
c)If you are using a handheld SPL meter with source material, such as a test disc or an audio selection, play it and adjust the AVR’s master volume control until the meter measures 75dB.
Press the OSD Button to display the Master Menu, and then navigate to the Manual Setup line. Press the OK Button to display the Manual Setup menu. Select the Level Adjust line and press the OK Button to display the Level Adjust menu. See Figure 30.
Figure 30 – Level Adjust Menu
All of the speaker channels will appear with their current level settings.
Channel Reset: To reset all of the levels to their factory defaults of 0dB, navigate to this line and change the setting to ON. The levels will be reset, and this setting will remain ON until one of the channel levels is adjusted.
If you are using an external source to set your output levels, navigate to each channel and use the 7/3Buttons to adjust the level as desired. If you would like to set your levels using the AVR 1600’s internal test tone, adjust the TEST TONE SEQ and TEST TONE lines as follows.
Test Tone SEQ: When this setting reads AUTO, the test tone will automatically circulate to all channels, pausing for a few moments at each channel for several seconds, as indicated by the blinking cursor. Adjust the level for any channel when the test tone is paused there by using the 7/3Buttons. You may also use the 5/1Buttons at any time to move the cursor to another line, and the test tone will follow the cursor.
When this setting reads MANUAL, the test tone will not move to the next channel until you use the 5/1Buttons.
Test Tone: This line determines whether the test tone is active. To begin the process of setting the levels, use the 7/3Buttons to change
the setting to ON. Any time you manually move the cursor out of the channel listings area of the screen, this setting will automatically change to OFF, stopping the test tone.
Individual Channels: If you are using an external source to set your output levels, navigate to each channel and use the
7/3 Buttons to adjust the level, between
When you have finished adjusting the speaker levels, select the Back to Manual Setup option or press the OSD Button. Record the level settings in Table A3 in the appendix.
AUDIO SETTINGS
To adjust other audio settings, such as the tone controls, press the OSD Button to display the Master Menu. With the cursor pointing to INPUT SETUP, press the OK Button to display the Input Setup menu, where the source, its title, its component video and audio inputs and Auto Polling status may be adjusted, as described in the Initial Setup section. However, this section will focus on the four audio settings:
BXR: Enhances bass performance when playing MP3 tracks. Select On, or leave at the default Off setting for
Tone: Determines whether the treble and bass controls are active. When it’s OUT, the tone controls are “flat”, with no changes. When it’s IN, the bass and treble frequencies are boosted or cut, depending upon the
Treble and Bass: Boost or cut the high or low frequencies by up to 10dB, 2dB at a time by using the 7/3 Buttons. The default setting is 0dB.
When you have finished, press the OSD Button.
SYSTEM SETTINGS
The AVR 1600 offers system settings for ease of use. These settings may be accessed from the System SETUP menu, which is selected by pressing the OSD Button and navigating to the System Setup line. Press the OK Button to display the System SETUP menu. See Figure 31.
Figure 31 – Systems Setup Menu
VFD Fade Time Out: Some people find the brightness of the AVR’s
34
