AT&T 76450 manual Other interconnection requirements, List of Documentation, Equipment lighting

Page 24

Common Systems Connection Standards

AT&T Services, Inc

Date: August 31, 2007

ATT-TP-76450, Issue 9

Note: The expectation is that a 2-3 page extraction from a larger manual will be submitted as evidence for each of the tasks above. Based on this information, AT&T may elect to conduct a more thorough review by accessing the information as listed below

7.13.2List of Documentation

Forward a list of all documentation that will be provided to AT&T for the planned deployment of the equipment (e.g., full document number, title and revision number for planning, installation, operations, etc.) and instructions on how AT&T can access these documents at this time (e.g., Public Website, Restricted client portal.)

.

7.13.3Provide a list sites where AT&T can gain access to the above documents today. (i.e. Public Website, Restricted client portal.)

8 Other interconnection requirements

8.1Equipment lighting

If NE includes integrated lighting system, the system shall meet the lighting and illumination requirements in ATT-TP-76400.

8.2Test (Streaker) Cards

Network Transport Elements shall have test cards (e.g., streaker) to enable verification of the network element hardware and the continuity of cabling, through the backplane, to the point of termination such as DSX panels or frames.

The test card or cards shall not:

require the shelf to be powered for such testing.

interrupt existing service on any other slot.

The test card or cards shall:

Provide metallic access to each backplane terminating conductor via an appropriate connector Bantam for DS1, including timing inputs, 440 for DS-3, STS-1 and E-3 Facilitate electrical signal insertion and transmission toward the drop; especially for DS1 or DS3 signals.

Facilitate optical signal insertion and transmission for continuity checking of optical jumpers that would, when such active Plug-In were installed, interconnect rear terminated Plug- Ins utilizing shelf backplane(s) optical connectors/barrels using SC or LC connectors.

Note: Test Set connections on face of Plug-In shall conform to AT&T standard connectors.

Copyright ©2004 – 2006, AT&T Knowledge Ventures

All rights reserved

Page 24

Image 24
Contents Canceled/Superseded Doc N/A Requirements PurposeScope Pre-assembled versus Field Assembled Network EquipmentATT-TP-76450 Internet Web Site Product Evaluation Process Additional AT&T RequirementsReasons for Reissue Adherence to AT&T Standard SuppliersAC Powered Equipment Redundant Power FeedsPower Feeds Nominal -48v DCBattery Return Conductor Drain DefinitionsList 1 Drain List 1X DrainLocation of Power Terminations 1 16 AWG Stranded Power Cable and LargerTwo Hole Connections 3 18 AWG Power Cable and Smaller Visual Power Alarms and Status IndicatorSize conductor Acceptable termination Associated Listings Fusing of Capacitors Power Distribution DeliveryNE Integrated Power Distribution Direct Bdfb Power DeliveryIndividually Mounted PDU Standards Synchronization/Timing Standards Termination of timing leadsClock output lead cabling Redundancy of timing inputsAlarms Output card exhaustionTL1 / TCP-IP TBOS/TABS Fiber Fiber AttenuatorsSee Figure Copper DS1 Cross-Connect Wire Central Office Copper Wire and Cable Vendor Documentation Unusual Cable TypesProtection of Cable and Jumpers Softcopy DocumentationAlarm/Trouble Shooting Guide Hard Copy DocumentationCraft Interface Instructions Personnel Injury and Equipment Damage WarningsConsistent Terminology throughout Documentation Consistent Terminology between Documentation and PlatformRevision Numbering Revision HistoryOther interconnection requirements List of DocumentationEquipment lighting Test Streaker CardsAppendix a ATT-TP-76450 Checklist Instructions and Process InstructionsProcess Page Power Interconnection Standards Alarm Standards Vendor Documentation Part & N/A Footnotes Rqmt# CommentAppendix C References Document Number Document DescriptionAppendix D ATT Contact List Appendix E Acronyms