Motorola 3.1 manual 2.4 VMM6300 Assembly Information, Installing the VMM6300 Device

Page 12

2.4VMM6300 Assembly Information

2.4VMM6300 Assembly Information

The VMM6300 Assembly shows the external connection points on a VMM6300 box.

		N-Type
		Antenna
Power	Power	Connector
Power	Power
Connector	Reset

Ethernet

(Crossover MDI-X)

Figure 2-1. VMM External Connection Point

2.5Installing the VMM6300 Device

The following instructions describe the VMM6300 hardware installation procedure:

1.Mount the VMM box in a suitable location in a vehicle to allow for ventilation. Note that the device is not waterproof and should be reasonably protected from moisture and other exposed outdoor environments.

2.Connect the antenna to the N-type connector.

3.Insert the Power Plug into Power Connector.

4.Verify that both MAC addresses have been recorded in Section 2.3.1, as this information will be required to configure and test the device.

5.If installing more than one IP device to the VMM6300, a separate hub device can be connected to the VMM ETH port. Up to three IP devices can be provisioned to interface with the VMM.

NOTE: For more information about how to configure additional devices to the VMM, refer to the External Device Provisioning section of this manual.

4

Image 12

Contents MEA 3.1 Vehicle Mounted Modem Users Guide Documentation RevisionPage Mesh Enabled Access VMM Users GuideCopyrights DisclaimerPage Table of Contents DEVICE INSTALLATIONDEVICE CONFIGURATION Mesh Enabled AccessVMM Users GuideDEVICE MAINTENANCE CUSTOMER SERVICE INFORMATIONSetting User Supplied IP Addresses Changing the Web Interface PasswordWARRANTY INFORMATION Regulatory and RF Safety ExposureREGULATORY INFORMATION Return Material RequestMEA Device Administration Home Page Super User Login MEA Device Administration Home Page Normal User LoginVMM Configuration Page Normal User Account Configuration Change Dialog1.1 Product Contents 1 Product Introduction2 Device Installation 2.1 Software Requirements2.2 Equipment Requirements 2.3 MAC Address Label Location 2.3.1 MAC Address TableMAC Address Table MAC Address 00-05-12-0A-xx-yy2.4 VMM6300 Assembly Information 2.5 Installing the VMM6300 DeviceFigure 2-1. VMM External Connection Point 2.6 Testing the Device Installation 2.5.1 Deployment Considerations2.5.1.1 Deployment Tips Figure 2-2. VMM6300 Trunk Mounting5. Right-click on the device MAC address and select the Ping option 3 Device Configuration 3.2 Accessing the MEA Device Administration Web Pages3.2.1 Administrator and Access Account Information 3.1 IP Addressing Considerations3.2.1.1 Password Information Administrator PasswordAccess User Password 3.2.2 Viewing MEA Device Administration Redirect Page Figure 3-2. MEA Device Administration Redirecting Web Page3.2.3 Viewing MEA Device Administration Home Page as an Administrator Figure 3-3. MEA Device Administration Home Page Super User Login3.2.4 Viewing MEA Device Administration Home Page as a Normal User Figure 3-4. MEA Device Administration Home Page Normal User Login3.2.5 VMM Device Administration Configuration Tab 3.2.5.1 Viewing the VMM Configuration Tab as an Administrator3.2.5.2 Viewing the VMM Configuration Tab as a Normal User Mesh Enabled AccessVehicle Mounted Modem Users GuideField Default Value Wired Interface3.2.6 VMM Device Administration Geo Position Tab Figure 3-6. VMM Configuration Page Normal User Account3.3 Device Addressing Schemes 3.3.1 Network DHCP Scheme 3.3.2 Statically Provisioned Scheme3.3.3 User Supplied Scheme 3.4 Setting User Supplied IP Addresses Figure 3-8. Configuration Change DialogFigure 3-9. System Update Save Completed Web Page 3.5 External Device Provisioning Figure 3-10. External Device Provisioning Table3.5.1 Connecting to the Ethernet Port 3.6 Working with MeshTrayselect Programs Æ mea Æ MeshTray.exe 3.6.1 MeshTray Status Information Figure 3-11. MeshTray Status Tab VMM3.6.3 MeshTray Authentication Activity 3.6.2 MeshTray Security TabFigure 3-12. MeshTray Security Tab VMM Figure 3-13. MeshTray Authentication Activity tab VMM 4 Device Maintenance 4.1 Changing the Web Interface PasswordFigure 4-1. Enter New Password Web Page Figure 4-2. Confirm Changes Window for Enter New Password Figure 4-3. Password Changed Confirmation Web PageFigure 4-4. Update Device Firmware Web Page 4.2 Upgrading the Device FirmwareFigure 4-5. Confirm Upload Window for Firmware Update Figure 4-6. Firmware Upload Progress Web PageOnce the filename has been confirmed, the web browser will transmit the file to the device, and the device will present an upgrade progress screen. This page will indicate the current stage in the upgrade process 4.3 Security Provisioning Web Page 4.3.1 Provision Username Section4.3.2 Provision Groupname Section Figure 4-7. Security Provisioning Web Page4.4 Resetting the VMM via the Device Administration Web Page Figure 4-8. Device Reset Prompt Web PageFigure 4-9. Device Reset in Progress Page 4.5 Restoring Factory Settings - User Supplied Mode Limitations 4.5.1 Recovering from VMM Reset-to-Default in User-Supplied Mode4.5.1.1 Resetting Device Addressing Mode Using Device Manager 4.5.1.2 Resetting Device Addressing Mode via Configuration Web Page4.6 Restoring Factory Settings - Normal Operations Figure 4-10. Restore Factory Settings Web PageFigure 4-11. Confirm Changes Window for Restore Factory Settings Figure 4-12. Factory Settings Restored Web PageThe Factory Settings Restored page will be displayed Click on the Finished button to complete the reset procedure5 Customer Service Information EuropeEmail essc@motorola.com Asia and Pacific Region5.2.1 Radio Products and Services Division 5.1 Obtaining Support5.2 Return Material Request 5.1.1 System Information5.2.1.1 Radio Products and Services Division Telephone Numbers 5.2.2 Returning System Components to Motorola5.2.3 Returning FREs 6 Warranty Information G Batteries they carry their own separate limited warranty P Loading of software upgrades or fixes into the devicesB Defects or damage from misuse, accident, water, or neglect F Product which has had the serial number removed or made illegibleequipment or software not furnished by Motorola which is attached to or used in connection with the Product. The foregoing states the entire liability of Motorola with respect to infringement of patents by the Product or any its parts thereof 7.3 Regulatory and RF Safety Exposure 7 Regulatory Information7.1 FCC Information 7.2 FCC RF Energy Exposure StatementRF Exposure Compliance and Guidelines Operating Instructions Ministry of Health Canada Safety Code 6. Limits of Human Exposure to