Motorola 3.1 manual Setting User Supplied IP Addresses, 8. Configuration Change Dialog

Page 25

3.4Setting User Supplied IP Addresses

Mesh Enabled Access

Vehicle Mounted Modem Users Guide

3.4Setting User Supplied IP Addresses

In order to set the user-supplied IP address for the VMM, the User-Supplied radio button must be selected. At that point, the user may enter an IP address and subnet mask consistent with the existing network. The user should also enter the IP address of the default gateway and DNS server, as well as enter the domain name.

Note that this configures the user-supplied address for the VMM device. To configure addresses for Ethernet clients, refer to the description in the External Device Provisioning section of this guide.

A similar screen will be displayed for the access account (the web page will indicate Normal User Login). Normal users can change only those settings for which they have system privileges.

When the desired configuration has been completed, click on the Apply button on the Device Addressing panel on the Device Administration Configuration Page. You will be prompted to verify that the changes to the configuration are correct before the changes are actually applied.

Figure 3-8. Configuration Change Dialog

When you click on the OK button, the configuration will be saved in flash. The System Settings Have Been Saved message, on the System Update Save Completed page, will then confirm that the changes have been saved.

17

Image 25

Contents Documentation Revision MEA 3.1 Vehicle Mounted Modem Users GuidePage VMM Users Guide Mesh Enabled AccessCopyrights DisclaimerPage DEVICE INSTALLATION Table of ContentsDEVICE CONFIGURATION Mesh Enabled AccessVMM Users GuideCUSTOMER SERVICE INFORMATION DEVICE MAINTENANCESetting User Supplied IP Addresses Changing the Web Interface PasswordRegulatory and RF Safety Exposure WARRANTY INFORMATIONREGULATORY INFORMATION Return Material RequestMEA Device Administration Home Page Normal User Login MEA Device Administration Home Page Super User LoginVMM Configuration Page Normal User Account Configuration Change Dialog1 Product Introduction 1.1 Product Contents2.1 Software Requirements 2 Device Installation2.2 Equipment Requirements 2.3.1 MAC Address Table 2.3 MAC Address Label LocationMAC Address Table MAC Address 00-05-12-0A-xx-yy2.5 Installing the VMM6300 Device 2.4 VMM6300 Assembly InformationFigure 2-1. VMM External Connection Point 2.5.1 Deployment Considerations 2.6 Testing the Device Installation2.5.1.1 Deployment Tips Figure 2-2. VMM6300 Trunk Mounting5. Right-click on the device MAC address and select the Ping option 3.2 Accessing the MEA Device Administration Web Pages 3 Device Configuration3.2.1 Administrator and Access Account Information 3.1 IP Addressing ConsiderationsAdministrator Password 3.2.1.1 Password InformationAccess User Password Figure 3-2. MEA Device Administration Redirecting Web Page 3.2.2 Viewing MEA Device Administration Redirect PageFigure 3-3. MEA Device Administration Home Page Super User Login 3.2.3 Viewing MEA Device Administration Home Page as an AdministratorFigure 3-4. MEA Device Administration Home Page Normal User Login 3.2.4 Viewing MEA Device Administration Home Page as a Normal User3.2.5.1 Viewing the VMM Configuration Tab as an Administrator 3.2.5 VMM Device Administration Configuration TabMesh Enabled AccessVehicle Mounted Modem Users Guide 3.2.5.2 Viewing the VMM Configuration Tab as a Normal UserField Default Value Wired InterfaceFigure 3-6. VMM Configuration Page Normal User Account 3.2.6 VMM Device Administration Geo Position Tab3.3 Device Addressing Schemes 3.3.2 Statically Provisioned Scheme 3.3.1 Network DHCP Scheme3.3.3 User Supplied Scheme Figure 3-8. Configuration Change Dialog 3.4 Setting User Supplied IP AddressesFigure 3-9. System Update Save Completed Web Page Figure 3-10. External Device Provisioning Table 3.5 External Device Provisioning3.6 Working with MeshTray 3.5.1 Connecting to the Ethernet Portselect Programs Æ mea Æ MeshTray.exe Figure 3-11. MeshTray Status Tab VMM 3.6.1 MeshTray Status Information3.6.2 MeshTray Security Tab 3.6.3 MeshTray Authentication ActivityFigure 3-12. MeshTray Security Tab VMM Figure 3-13. MeshTray Authentication Activity tab VMM 4.1 Changing the Web Interface Password 4 Device MaintenanceFigure 4-1. Enter New Password Web Page Figure 4-3. Password Changed Confirmation Web Page Figure 4-2. Confirm Changes Window for Enter New Password4.2 Upgrading the Device Firmware Figure 4-4. Update Device Firmware Web PageFigure 4-6. Firmware Upload Progress Web Page Figure 4-5. Confirm Upload Window for Firmware UpdateOnce the filename has been confirmed, the web browser will transmit the file to the device, and the device will present an upgrade progress screen. This page will indicate the current stage in the upgrade process 4.3.1 Provision Username Section 4.3 Security Provisioning Web Page4.3.2 Provision Groupname Section Figure 4-7. Security Provisioning Web PageFigure 4-8. Device Reset Prompt Web Page 4.4 Resetting the VMM via the Device Administration Web PageFigure 4-9. Device Reset in Progress Page 4.5.1 Recovering from VMM Reset-to-Default in User-Supplied Mode 4.5 Restoring Factory Settings - User Supplied Mode Limitations4.5.1.1 Resetting Device Addressing Mode Using Device Manager 4.5.1.2 Resetting Device Addressing Mode via Configuration Web PageFigure 4-10. Restore Factory Settings Web Page 4.6 Restoring Factory Settings - Normal OperationsFigure 4-12. Factory Settings Restored Web Page Figure 4-11. Confirm Changes Window for Restore Factory SettingsThe Factory Settings Restored page will be displayed Click on the Finished button to complete the reset procedureEurope 5 Customer Service InformationEmail essc@motorola.com Asia and Pacific Region5.1 Obtaining Support 5.2.1 Radio Products and Services Division5.2 Return Material Request 5.1.1 System Information5.2.2 Returning System Components to Motorola 5.2.1.1 Radio Products and Services Division Telephone Numbers5.2.3 Returning FREs 6 Warranty Information P Loading of software upgrades or fixes into the devices G Batteries they carry their own separate limited warrantyB Defects or damage from misuse, accident, water, or neglect F Product which has had the serial number removed or made illegibleequipment or software not furnished by Motorola which is attached to or used in connection with the Product. The foregoing states the entire liability of Motorola with respect to infringement of patents by the Product or any its parts thereof 7 Regulatory Information 7.3 Regulatory and RF Safety Exposure7.1 FCC Information 7.2 FCC RF Energy Exposure StatementMinistry of Health Canada Safety Code 6. Limits of Human Exposure to RF Exposure Compliance and Guidelines Operating Instructions