Motorola SM56 manual +Vrid, +Vrx, +Vsd

Page 27

Table 4: AT+ (Plus) Commands

Command

Option

Description

 

 

 

 

 

If, after detecting ringback, no further ringbacks are

 

 

detected after n/10 seconds, operate as if the remote

 

 

device answered the call.

 

+VRA=n

If no ringback is received, after n/10 seconds,

 

 

assume that the remote device has answered the call;

 

 

n = 0-255

 

 

 

 

 

Ringback Never Occurred

 

 

 

 

+VRN=n

After n/10 seconds, operate as if ringback never

 

 

occurred; n = 0-255

+VRID

 

Repeat Caller ID

 

 

 

 

 

This command instructs the modem to send all avail-

 

 

able call information on the last incoming call to the

 

 

DTE.

 

 

Note: “AT+VRID” is identical to “AT+VRID=0”

 

 

 

 

+VRID or

Display Caller ID information in formatted form

 

+VRID=0

 

 

 

 

+VRID=1

Display Caller ID information in unformatted form

 

 

 

 

+VRID=?

Display Repeat Caller ID Status

 

 

 

+VRX

 

Voice Receive Mode

 

 

 

 

 

Data/Fax/Speakerphone modem only

 

 

 

 

 

Determines whether the modem generates a periodic

 

 

beep, audible to both parties on the speakerphone,

 

 

indicating that the call is being recorded.

 

 

 

 

Note

 

 

 

 

 

 

 

 

 

 

 

 

The speakerphone state does not have to be reset

 

 

 

 

after recording to the line or playing a message

 

 

 

 

to the line. The baud rate is not set before the

 

 

 

 

StartPlay and StartRecord commands. The baud

 

 

 

 

rate is not reset after the StopPlay and

 

 

 

 

StopRecord commands.

 

+VRX or

Produce Periodic DCE Tone While Recording

 

+VRX=0

 

 

 

 

 

 

 

+VRX=1

Disable Periodic DCE Tone Production During

 

 

Recording

+VSD

 

Remote Silence-Detection Properties

 

 

 

 

 

Data/Fax/Speakerphone modem only

 

 

 

 

+VSD=m,n

Used in answering-machine mode. Specifies the vol-

 

 

ume and duration thresholds that determine whether

 

 

the remote device has hung up.

 

m options:

Specifies the silence-detection level

 

 

 

 

 

25

Image 27
Contents AT Command Reference Manual UbiSurf SM56 Introduction Page AT and AT& Commands Pulse Dial Speaker VolumeReturn to On-Line Mode Speaker ControlSelect Call-Progress Result Codes to Return Reset Modem Parameters to Default ConfigurationTone Dial Result-Code FormatCTS Control Initialize modem to default factory configurationDial TX Level Pulse CycleMaximum Modulation Rate AT% Percent and AT\ Backslash CommandsData Compression DC Mode Disconnect Buffer DelayMinimum Modulation Rate AT% Percent and AT\ Backslash Commands Disconnect on DTE Inactivity Error-Correction EC ModeBreak Handling Method DTE Flow ControlLow-Speed Operation Protocol AT* Asterisk CommandsModulation Mode Dial WaitMM14 K56flex Auto-modulation MM15 Only MM16 MM17 MM18 AT+ Plus Commands +A8E Configuration+A8T 8bis Signal and Message Control Data Compression Control +DRData Compression DC Reporting +DS+EB +ER+ES +ESA Synchronous Access Mode Configuration+ETBM +FCLASS+FLO +FRH +FMI?+FMM? +FMR?AT+ Plus Commands +IFC +GMI+GMM +GMR+MR +PCW +PMH+PMHT +VCID +PMHR+PMF +PQC+VIP +VEM+VGR +VGT+VRID +VRX+VSD +VSM +VTD+VTS +VTX Enter Voice-Transmission ModeATS S-Register Commands S92 Modem-on-Hold Messaging Monitoring S18 Test TimerS11 Tone Length S12 Escape Code Guard TimeCommand Syntax Command ResponseAT#UD Last Call Status Report Format Ffffffff Call Setup Result Codes DTE-DCE modes Multimedia modesGstnModulationSchemeActive from 3.7.2/V.58 ErrorControl Active from 3.5.2/V.58CallCleared codes from 3.6.4/V.58-1994 CompressionActive from 3.2.2/V.58CallCleared codes from 3.6.4/V.58-1994 Modem response line Description Event Reporting Word Busy
Related manuals
Manual 22 pages 12.61 Kb Manual 13 pages 49.27 Kb