Motorola SM56 manual S11 Tone Length, S12 Escape Code Guard Time, S18 Test Timer

Page 31

Table 5: ATS (S-Register) Commands

S-Register

Option

Description

 

 

 

 

S10=n

Disconnect after n seconds; n=0 to 255 in 0.1 second

 

 

increments; after DCD signal is de-asserted. Default

 

 

= 14

S11

 

Tone Length

 

 

 

 

S11=n

Specifies duration, in 0.001 second increments, of

 

 

DTMF tone when it is generated; n=60 to 255.

 

 

Default =80

S12

 

Escape Code Guard Time

 

 

 

 

S12=n

Specifies the interval, in 0.02-second increments,

 

 

that must be present on either side of the escape code

 

 

(+++) for the modem to recognize the escape com-

 

 

mand and enter command mode. If S12=0, the speed

 

 

at which you enter the escape sequence is not a fac-

 

 

tor. Default = 50

 

 

 

S18

 

Test Timer

 

 

 

 

S18=n

Specifies test execution duration; n=0 to 255.

 

 

Default = 0

S92

 

Modem-on-Hold Messaging Monitoring

 

 

 

 

S92=n

Specifies the enable(n=1) or disable(n=0) of the

 

 

Modem-on-Hold UbiSurf SM56 tray applet helper

 

 

messaging. Default = 1

29

Image 31
Contents AT Command Reference Manual UbiSurf SM56 Introduction Page AT and AT& Commands Pulse Dial Speaker VolumeReturn to On-Line Mode Speaker ControlSelect Call-Progress Result Codes to Return Reset Modem Parameters to Default ConfigurationTone Dial Result-Code FormatCTS Control Initialize modem to default factory configurationDial TX Level Pulse CycleMaximum Modulation Rate AT% Percent and AT\ Backslash CommandsDisconnect Buffer Delay Data Compression DC ModeMinimum Modulation Rate AT% Percent and AT\ Backslash Commands Disconnect on DTE Inactivity Error-Correction EC ModeBreak Handling Method DTE Flow ControlLow-Speed Operation Protocol AT* Asterisk CommandsModulation Mode Dial WaitMM14 K56flex Auto-modulation MM15 Only MM16 MM17 MM18 +A8E Configuration AT+ Plus Commands+A8T 8bis Signal and Message Control Data Compression Control +DRData Compression DC Reporting +DS+ER +EB+ES +ESA Synchronous Access Mode Configuration+FCLASS +ETBM+FLO +FRH +FMI?+FMM? +FMR?AT+ Plus Commands +IFC +GMI+GMM +GMR+MR +PMH +PCW+PMHT +VCID +PMHR+PMF +PQC+VIP +VEM+VGR +VGT+VRX +VRID+VSD +VTD +VSM+VTS +VTX Enter Voice-Transmission ModeATS S-Register Commands S92 Modem-on-Hold Messaging Monitoring S18 Test TimerS11 Tone Length S12 Escape Code Guard TimeCommand Response Command SyntaxAT#UD Last Call Status Report Format Ffffffff Call Setup Result Codes DTE-DCE modes Multimedia modesGstnModulationSchemeActive from 3.7.2/V.58 ErrorControl Active from 3.5.2/V.58CallCleared codes from 3.6.4/V.58-1994 CompressionActive from 3.2.2/V.58CallCleared codes from 3.6.4/V.58-1994 Modem response line Description Event Reporting Word Busy
Related manuals
Manual 22 pages 12.61 Kb Manual 13 pages 49.27 Kb