Motorola SM56 manual Event Reporting Word

Page 40

Table 15 - Completed Data Call, with some errors and rate retrain during the call

Event Reporting Word

Modem response line

Description

 

 

DIAG <2

No carrier loss events, 3 carrier rate rene-

A4D3263 30=00 31=03 32=01

gotiations attempted; 1 carrier retrain

33=01>

requested; 1 carrier retrain granted

 

 

DIAG <2A4D3263 34=7080

Final transmit rate is 28800 bit/s; final

35=CB20>

receive rate is 52000 bit/s

 

 

DIAG <2A4D3263 40=1 41=100>

LAPM negotiation completed; frame

 

size = 256

DIAG <2A4D3263 42=0 43=0>

No error control timeout or link NAKs

 

 

DIAG <2A4D3263 44=1 45=400>

V.42bis data compression used; dictio-

 

nary size = 1024

 

 

DIAG <2A4D3263 50=2 51=2>

Hardware transmit and receive flow con-

 

trol

DIAG <2A4D3263 52=343CC 54=0>

213964 DTE characters transmitted, w/o

 

underrun

DIAG <2A4D3263 53=7230E6

7483622 DTE characters received, 71

55=47>

characters lost due to receive data over-

 

run

 

 

DIAG <2A4D3263 56=29D 58=0001>

597 (decimal) frames transmitted, with 1

 

frame error

DIAG <2A4D3263 58=2A4B

10827 (decimal) frames received, with 4

59=0004>

frame errors

DIAG <2A4D3263 60=51>

Local PC initiated hangup

 

 

You can use the AT+VEM command to define events on which to report. The list is encoded as a word composed of the following bits.

Note

All events are enabled by default and indicated by the underlined bit number. Blank table entries are unsupported events.

A 1 in a bit-position indicates an event is reported.

A 0 in a bit-position indicates an event is not reported.

Read bits from right (Bit 0) to left (Bit 32).

Bit

Signal

0Caller ID (effective only where function is supported by the phone company. Not supported on Data/Fax modems.

1

2Distinctive Ring (effective only where function is supported

38

Image 40
Contents AT Command Reference Manual UbiSurf SM56 Introduction Page AT and AT& Commands Speaker Volume Return to On-Line ModeSpeaker Control Pulse DialReset Modem Parameters to Default Configuration Tone DialResult-Code Format Select Call-Progress Result Codes to ReturnInitialize modem to default factory configuration Dial TX LevelPulse Cycle CTS ControlAT% Percent and AT\ Backslash Commands Maximum Modulation RateDisconnect Buffer Delay Data Compression DC ModeMinimum Modulation Rate AT% Percent and AT\ Backslash Commands Error-Correction EC Mode Break Handling MethodDTE Flow Control Disconnect on DTE InactivityAT* Asterisk Commands Modulation ModeDial Wait Low-Speed Operation ProtocolMM14 K56flex Auto-modulation MM15 Only MM16 MM17 MM18 +A8E Configuration AT+ Plus Commands+A8T 8bis Signal and Message Control +DR Data Compression DC Reporting+DS Data Compression Control+ER +EB+ES Synchronous Access Mode Configuration +ESA+FCLASS +ETBM+FLO +FMI? +FMM?+FMR? +FRHAT+ Plus Commands +GMI +GMM+GMR +IFC+MR +PMH +PCW+PMHT +PMHR +PMF+PQC +VCID+VEM +VGR+VGT +VIP+VRX +VRID+VSD +VTD +VSM+VTS Enter Voice-Transmission Mode +VTXATS S-Register Commands S18 Test Timer S11 Tone LengthS12 Escape Code Guard Time S92 Modem-on-Hold Messaging MonitoringCommand Response Command SyntaxAT#UD Last Call Status Report Format Ffffffff Call Setup Result Codes Multimedia modes DTE-DCE modesErrorControl Active from 3.5.2/V.58 GstnModulationSchemeActive from 3.7.2/V.58CompressionActive from 3.2.2/V.58 CallCleared codes from 3.6.4/V.58-1994CallCleared codes from 3.6.4/V.58-1994 Modem response line Description Event Reporting Word Busy
Related manuals
Manual 22 pages 12.61 Kb Manual 13 pages 49.27 Kb