Motorola PRPMC800A/IH5 manual EMC Compliance, Environmental Characteristics

Page 78

A Specifications

Environmental Characteristics

Table 0-1. PrPMC800/800ET Environmental Specifications

Characteristics		Specifications

Temperature	Operating	−40° C to 70°C (32° F to 148° F)
	Nonoperating	−40° C to 70°C (32° F to 148° F)

Altitude	Operating	4,000 meters (13,123 feet)
	Nonoperating	15,000 meters (49,212 feet)

Relative Humidity	Operating	5% to 85% (noncondensing)
	Nonoperating	5% to 95% (noncondensing

Vibration	Operating	1.0	G sine sweep, 5.0 to 100 Hz, 25 octaves/min
	Nonoperating	0.5	G sine sweep;5-50 Hz; 0.1 octaves/min
		3.0	G sine sweep; 50-500 Hz;0.25 octaves/min

EMC Compliance

The PrPMC800/800ET is an add-on module meant to be used in conjunction with standard VME, CompactPCI, or ATX baseboard applications. As such, it is the responsibility of the OEM to meet the regulatory guidelines as determined by their application.

The PrPMC800/800ET has been tested in conjunction with a standard ECC baseboard and chassis for CE certification and meets the requirements for EN55022 Class A equipment. Compliance was achieved under the following conditions:

❏Shielded cables on all external I/O ports.

❏Cable shields connected to earth ground via metal shell connectors bonded to a conductive module front panel.

❏Conductive chassis rails connected to earth ground. This provides the path for connecting shields to earth ground.

❏Front panel screws properly tightened.

For minimum RF emissions, it is essential that the conditions above be implemented. Failure to do so could compromise the EMC compliance of the equipment containing the module.

58PrPMC800/800ET Processor PMC Module Installation and Use (PrPMC800A/IH5)

Image 78

Contents Installation and Use Page Do Not Operate in an Explosive Atmosphere Use Caution When Exposing or Handling a CRTGround the Instrument Keep Away From Live Circuits Inside the EquipmentFlammability Limited and Restricted Rights Legend Page Contents Connector Pin Assignments Modifying the Environment Contents List of Figures List of Figures J2 Harrier Power-Up Configuration Header Pin Assignments List of TablesList of Tables 1MB PrPMC800/800ET Models/ConfigurationsAbout This Manual 2MBAbout This Manual PRPMC800A/IH3 PRPMC800A/IH5PRPMC800A/IH4 PRPMC800A/IH2Overview of Contents Conventions Used in This Manual About This Manual Preparation and Installation IntroductionPrPMC800/800ET Description Monarch and Non-Monarch PrPMCs Carrier Board RequirementsSystem Enclosure Overview of Start-Up Procedures Start-Up OverviewWhat you need to do Refer to PrPMC800/800ET Configuration Unpacking the HardwarePreparing the Hardware Harrier Power-Up Configuration Header J2 Harrier Power-Up Configuration Header Pin AssignmentsJumper On Jumper Off PrPMC800/800ET Headers, Connectors and Components Installation ESD PrecautionsInstallation of PrPMC800/800ET on a VME or CompactPCI Board Installing a PrPMC800/800ET on a VMEmodule Applying Power Operating InstructionsStatus Indicators Operating InstructionsDebug Serial Port Ethernet Port Adapter CablePrPMC800/800ET Debug Page Feature Description FeaturesPrPMC800/800ET Features Functional DescriptionGeneral Description SromBlock Diagram PrPMC800/800ET Block DiagramProcessor L2 CacheHarrier System Memory Controller / PCI Host Bridge Asic Harrier Select Default Function Description Harrier Power-Up ConfigurationHarrier Power-Up Configuration Settings Option Power Register Bit Bus Signal SettingM66EN XCSR.GCSR.PUSTXAD XCSR.XPAT0.DWXCSR.XPAT1.DW ArbitrationFlash Memory XCSR.XPAT2.DWOptional Bank B Flash ECC MemoryOnboard Bank a Flash Onboard Sdram10BaseT/100BaseTX Ethernet Channel TimersBit Timers Miscellaneous Control and StatusAsynchronous Serial Port Watchdog TimersInterrupt Routing and Generation Clock GeneratorReset Source Functions PrPMC800/800ET Power SuppliesModule Reset Logic Reset Source Type Module Reset PrPMC Resetoutl ActivePrPMC800/800ET Reset Block Diagram PCI InterfaceINTA#-INTD# Signals PRESENT# SignalMONARCH# Signal IDSELB, REQB#, and GNTB# SignalsABORT# and RESET# Signals Eready SignalPCI Signaling Voltage Level Debug HeaderMemory Maps Page Connector Pin Assignments PCI Mezzanine Card PMC ConnectorsPMC Connector P11 Pin Assignments SDONE# SBO# PAR GND VIO GND VIOPMC Connector P12 Pin Assignments PMC Connector P13 Pin Assignments PAR64PMC Connector P14 Pin Assignments P14Signal Description for P14 J1 Debug Header Pin Assignments Ethernet Adapter ConnectorJ3 Ethernet Adapter Connector Pin Assignments TXP TXN RXP RXN Lanterma LantermbSignal Description for J1 RsvdShunt On Shunt Off Cputrstl Pullup Cputck Cputms Sresetl Cpurstl Ckstpol GND Debug Serial Port CablePrPMC Cable-001 Termination PPCBug OverviewPPCBug Basics Memory Requirements PPCBug ImplementationMPU, Hardware, and Firmware Initialization Using PPCBug Debugger Commands Debugger CommandsCommand Description Idle GevinitGevshow IOCNping PbootReset NopaDiagnostic Tests Diagnostic Test GroupsTest Group Description Mask IsabrdgeL2CACHE MpicPage Cnfg Configure Board Information Block Modifying the EnvironmentConfiguring the PPCBug Parameters ENV Set EnvironmentSelect the identifier. Default = Default = $00 Auto Boot Abort Delay = 7? Default Starting Address is $00000000 ROM First Access Length 0 31 = 10? Serial Startup Code Master Enable Y/N=N? Mechanical Characteristics SpecificationsSpecifications Electrical CharacteristicsEnvironmental Characteristics Characteristics SpecificationsEMC Compliance Thermal Validation Thermally Significant ComponentsTable B-1. Thermally Significant Components Thermal ValidationFigure B-1. Thermally Significant Components Primary Side Component Temperature Measurement PreparationMeasuring Junction Temperature Measuring Case TemperatureMeasuring Local Air Temperature Figure B-4. Mounting a Thermocouple Under a Heatsink Related Documentation Embedded Communications Computing DocumentsTable C-1. Embedded Communications Computing Documents Manufacturers’ Documents Table C-2. Manufacturers’ DocumentsRelated Specifications Table C-3. Related SpecificationsDocument Title and Source Publication Number Page Index CPUIndex Fail LEDIDSELB, REQB#, GNTB# 25 INTA#-INTD# Xix