Motorola PrPMC800/800ET Processor PMC Module, PRPMC800A/IH5 manual About This Manual, 1MB, 2MB

Page 15

About This Manual

PrPMC800/800ET Processor PMC Module Installation and Use provides information for installation and configuration of the PrPMC800/800ET, including jumper settings and installation procedures. It also includes descriptions of various components’ functions, connector pinout information, and a general description of the PPCBug firmware used with the board.

Information in this manual applies to Motorola boards that are compatible with the PowerPC™ instruction set architecture and that use PPCBug as their resident debugger program. The majority of these boards, including most Processor PMC, VME, CompactPCI® and ATX form factors, are equipped with PPCBug.

This document is limited to the installation and use instructions. For programming information, refer to the Harrier ASIC Programmer’s Reference Guide and the PrPMC800/800ET Processor PMC Module Programmer’s Reference Guide.

The following table lists the various model numbers and configurations for the PrPMC800/800ET. Note that some of the models listed below qualify as Class B devices. If you require a Class B device, contact your Motorola sales representative for specific models and configurations that meet those requirements.

Table 2-1. PrPMC800/800ET Models/Configurations

Model Number	Processor /	L2	Memory	Ethernet	PCI Bus
PrPMC800	Speed	Cache			Speed
PrPMC800-5251	MPC750 Class/	1MB	128MB	Front	33 MHz
	450 MHz

PrPMC800-5261	MPC750 Class/	1MB	256MB	Front	33 MHz
	450 MHz

PrPMC800-5271	MPC750 Class/	1MB	512MB	Front	33 MHz
	450 MHz

PrPMC800-1261	MPC7410/	2MB	256MB	Front	33 MHz
	450 MHz

PrPMC800-1271	MPC7410/	2MB	512MB	Front	33 MHz
	450 MHz

PrPMC800-5259	MPC750 Class/	1MB	128MB	Rear	33 MHz
	450 MHz

PrPMC800-5269	MPC750 Class/	1MB	256MB	Rear	33 MHz

450MHz

*Industrial temperature models

For RoHS compliant models of these boards, please contact your local Motorola sales representative.

PrPMC800/800ET Processor PMC Module Installation and Use (PrPMC800A/IH5)

xv

Image 15

Contents Installation and Use Page Keep Away From Live Circuits Inside the Equipment Use Caution When Exposing or Handling a CRTGround the Instrument Do Not Operate in an Explosive AtmosphereFlammability Limited and Restricted Rights Legend Page Contents Connector Pin Assignments Modifying the Environment Contents List of Figures List of Figures List of Tables J2 Harrier Power-Up Configuration Header Pin AssignmentsList of Tables 2MB PrPMC800/800ET Models/ConfigurationsAbout This Manual 1MBAbout This Manual PRPMC800A/IH2 PRPMC800A/IH5PRPMC800A/IH4 PRPMC800A/IH3Overview of Contents Conventions Used in This Manual About This Manual Preparation and Installation IntroductionPrPMC800/800ET Description Monarch and Non-Monarch PrPMCs Carrier Board RequirementsSystem Enclosure Overview of Start-Up Procedures Start-Up OverviewWhat you need to do Refer to PrPMC800/800ET Configuration Unpacking the HardwarePreparing the Hardware Harrier Power-Up Configuration Header J2 Harrier Power-Up Configuration Header Pin AssignmentsJumper On Jumper Off PrPMC800/800ET Headers, Connectors and Components Installation ESD PrecautionsInstallation of PrPMC800/800ET on a VME or CompactPCI Board Installing a PrPMC800/800ET on a VMEmodule Operating Instructions Applying PowerOperating Instructions Status IndicatorsDebug Serial Port Ethernet Port Adapter CablePrPMC800/800ET Debug Page Functional Description FeaturesPrPMC800/800ET Features Feature DescriptionSrom General DescriptionPrPMC800/800ET Block Diagram Block DiagramProcessor L2 CacheHarrier System Memory Controller / PCI Host Bridge Asic Option Power Register Bit Bus Signal Setting Harrier Power-Up ConfigurationHarrier Power-Up Configuration Settings Harrier Select Default Function DescriptionXCSR.XPAT0.DW XCSR.GCSR.PUSTXAD M66ENXCSR.XPAT2.DW ArbitrationFlash Memory XCSR.XPAT1.DWOnboard Sdram ECC MemoryOnboard Bank a Flash Optional Bank B FlashMiscellaneous Control and Status TimersBit Timers 10BaseT/100BaseTX Ethernet ChannelClock Generator Watchdog TimersInterrupt Routing and Generation Asynchronous Serial PortReset Source Type Module Reset PrPMC Resetoutl Active PrPMC800/800ET Power SuppliesModule Reset Logic Reset Source FunctionsPCI Interface PrPMC800/800ET Reset Block DiagramIDSELB, REQB#, and GNTB# Signals PRESENT# SignalMONARCH# Signal INTA#-INTD# SignalsDebug Header Eready SignalPCI Signaling Voltage Level ABORT# and RESET# SignalsMemory Maps Page Connector Pin Assignments PCI Mezzanine Card PMC ConnectorsPMC Connector P11 Pin Assignments GND VIO SDONE# SBO# PAR GND VIOPMC Connector P12 Pin Assignments PAR64 PMC Connector P13 Pin AssignmentsP14 PMC Connector P14 Pin AssignmentsSignal Description for P14 TXP TXN RXP RXN Lanterma Lantermb Ethernet Adapter ConnectorJ3 Ethernet Adapter Connector Pin Assignments J1 Debug Header Pin AssignmentsRsvd Signal Description for J1Shunt On Shunt Off Cputrstl Pullup Cputck Cputms Sresetl Cpurstl Ckstpol GND Debug Serial Port CablePrPMC Cable-001 Termination PPCBug OverviewPPCBug Basics PPCBug Implementation Memory RequirementsMPU, Hardware, and Firmware Initialization Using PPCBug Debugger Commands Debugger CommandsCommand Description IOC GevinitGevshow IdleNopa PbootReset NpingDiagnostic Tests Diagnostic Test GroupsTest Group Description Mpic IsabrdgeL2CACHE MaskPage Modifying the Environment Cnfg Configure Board Information BlockENV Set Environment Configuring the PPCBug ParametersSelect the identifier. Default = Default = $00 Auto Boot Abort Delay = 7? Default Starting Address is $00000000 ROM First Access Length 0 31 = 10? Serial Startup Code Master Enable Y/N=N? Electrical Characteristics SpecificationsSpecifications Mechanical CharacteristicsEnvironmental Characteristics Characteristics SpecificationsEMC Compliance Thermally Significant Components Thermal ValidationThermal Validation Table B-1. Thermally Significant ComponentsFigure B-1. Thermally Significant Components Primary Side Preparation Component Temperature MeasurementMeasuring Junction Temperature Measuring Case TemperatureMeasuring Local Air Temperature Figure B-4. Mounting a Thermocouple Under a Heatsink Related Documentation Embedded Communications Computing DocumentsTable C-1. Embedded Communications Computing Documents Table C-2. Manufacturers’ Documents Manufacturers’ DocumentsRelated Specifications Table C-3. Related SpecificationsDocument Title and Source Publication Number Page CPU IndexFail LED IndexIDSELB, REQB#, GNTB# 25 INTA#-INTD# Xix