SECTION 10: WIRING
SECTION 10: WIRING
DANGER
Electrical Shock Hazard
Disconnect electric before service.
Heater must be properly grounded.
Failure to follow these instructions can result in death or electrical shock.
FIGURE 22: Zone Sensor Wiring Diagram
Heater must be grounded in accordance with applicable codes: United States: refer to National
Electrical Code® NFPA 70 - latest revision Canada: refer to Canadian Electrical Code, CSA C22.1 Part I - latest revision.
If any of the original internal wiring must be replaced, it must be replaced with wiring materials having a temperature rating of at least 105°C and 600 Volts.
10.1 Standard Heater Configuration
From the factory, the heater is configured for zone sensor control. Connect zone sensor to the heater control as shown on Page 39, Figure 22.
If additional heaters are in the same heating zone, control wiring must be installed between the heaters’ controls as shown on Page 39, Figure 22.
For additional details or for use with heat demand control devices other than the zone sensor, see Page 40, Section 10.2 through Page 48, Section 10.4.9.
ZONE SENSOR
CENTRAL HEATER CONTROL
* Separate on/off switch is optional for |
ON
OFF
SET SEN +FAN- | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
THERMOSTAT |
|
| |
T24 |
|
|
|
| R |
| |
T25 |
|
|
|
| W |
| |
T26 |
|
|
|
| + | ANALOG |
|
T27 | INPUT |
| |
|
| ||
| - |
| |
T13 |
| THERMISTOR |
|
T14 | GND |
| |
|
| ||
T15 | SLIDE BAR |
| |
T16 |
| ||
GND |
|
| |
|
|
| |
T17 | HIGH WIPER |
|
|
T18 | EXT. POT |
| |
T19 |
| ||
| GND |
|
|
T28 |
|
|
|
| + | FIRING RATE |
|
T29 | IN |
| |
| - |
| |
T30 |
|
|
|
T31 | FIRING RATE + OUT - | A B | |
|
| ||
|
|
| J10 |
"satellite" heaters (install at user level). On/ |
Off switch is used to disable heater operation |
or reset a heater that is in "lockout" mode. If |
on/off switch is not desired, leave jumper wire |
between R and W terminals in place. |
*OPTIONAL | SATELLITE HEATER CONTROL | ||
SWITCH |
|
|
|
| THERMOSTAT |
| |
| T24 |
|
|
|
| R | |
| T25 |
|
|
|
| W | |
| T26 |
|
|
|
| + | ANALOG |
| T27 | INPUT | |
|
| ||
|
| - | |
| T13 |
| THERMISTOR |
| T14 | GND | |
|
| ||
| T15 | SLIDE BAR | |
| T16 | ||
| GND |
| |
|
|
| |
| T17 | HIGH WIPER |
|
| T18 | EXT. POT | |
| T19 | ||
MODULATION CONTROL WIRING
TO SATELLITE HEATERS
Description | Part Number |
Zone Sensor, 40° - 75° | 10081530 |
|
|
| GND |
|
|
|
|
|
|
|
|
|
|
|
|
| |
T28 |
|
|
|
|
|
|
|
| + | FIRING RATE |
|
|
|
|
|
|
|
|
|
|
|
| |
T29 | IN |
|
|
|
|
| |
| - |
|
|
|
|
| |
|
|
|
|
|
|
|
|
T30 |
|
|
|
|
|
|
|
| + |
|
|
|
|
|
|
| FIRING RATE OUT - | A B |
| ||||
T31 |
| ||||||
|
|
| J10 |
| |||
|
|
|
| ||||
MODULATION CONTROL WIRING
TO ADDITIONAL SATELLITE
HEATERS CONTROL TERMINALS
T28 and T29.
39 of 71
