Creative GCD-R542B Connecting Cables to Your Card, Connecting CD audio cable to your CD-ROM drive

Page 22

4.If you are connecting your drive to an audio card, connect the CD audio cable to the CD-ROM drive as shown in Figure 2-9.

Figure 2-9: Connecting CD audio cable to your CD-ROM drive.

Connecting Cables to Your Card

After connecting the cables to the CD-ROM’s rear panel, you need to connect these cables to your audio or IDE CD-ROM interface card.

If you have purchased the drive in a multimedia upgrade kit, read “Connecting Cables to Your Audio Card” in this section.

If you have purchased your drive with the IDE CD-ROM interface card, read “Connecting Cables to Your IDE CD-ROM Interface Card” in this section.

If you have purchased the drive as a stand-alone product, read “Connecting Cables to Your Audio Card” to connect the drive to an audio card or “Connecting Cables to Your IDE CD-ROM Interface Card” to connect the drive to an IDE CD-ROM interface card.

If you are connecting your drive to your hard disk controller card, read “Connecting Cables to Your Hard Disk Controller Card” in this section.

Setting Up Your CD-ROM Drive 2-7

Image 22

Contents CD ROM Upgrade CD-ROM Upgrade Regulatory Information ModificationsSafety Information Compliance Checking System Requirements IntroductionBefore You Begin Obtaining Latest InformationUsing this Guide Making a Copy of Your DiskettesDocument Conventions Text Element Use Bold Icon Use Knowing Your CD-ROM Drive Drive’s Front Panel Volume ControlBusy Indicator Stereo Phone JackStop/Eject Button Play/Skip ButtonEject Hole Disc TrayHolding a disc Digital Output Connector Drive’s Rear PanelPower-in Connector CD Audio ConnectorIDE CD-ROM Data Connector Master/Slave JumperSetting Up Your CD-ROM Drive Items required for setting up your CD-ROM driveInstalling Your Drive IDE CD-ROM interface cardInserting Your Drive into Your System Vacating a drive bay Connecting Cables to Your Drive’s Rear Panel Inserting your CD-ROM driveConnecting power cable to your CD-ROM drive Connecting Cables to Your Card Connecting CD audio cable to your CD-ROM drive10 Connecting data cable to the audio card 12 Fastening the drives to your system 13 Locating a vacant slot 15 Inserting the IDE CD-ROM interface card 17 Connecting the data cable to the interface card 19 Fastening the drives to your system Page Page 22 Connecting the CD audio cable to the audio card Installing the Software 23 Fastening the drives to your systemTesting the Installation CONFIG.SYSSetting Up Your CD-ROM Drive Using QuickCD Running DOS QuickCDUnderstanding the DOS QuickCD Screen QuickCD screenThis function is ignored Running Windows QuickCD Quitting DOS QuickCDProgram Item Properties dialog box Select MCI CD Audio from the Add dialog box Starting Windows QuickCD Understanding the Windows QuickCD Control WindowForwards the current track by 10 seconds Using the Control Menu Box Control menuCustomizing Windows QuickCD Preferences dialog boxQuitting Windows QuickCD Changing the Driver Settings Doing More with Your CD-ROM DriveSBIDE.SYS Settings IDE Port Addr, irq Addresses Used MSCDEX.EXE Settings Running Cdsetup Locking the Disc TrayConnecting Additional Drives Configuring the Master/Slave Jumper Setting Enabling and Disabling JumpersJumper labeled CS is reserved and should not be used Connecting the Drives Daisy-chaining the drivesPhysical Dimensions Technical DataPerformance Characteristics Typical Audio Performance Environmental Operating LimitsResolving Hardware Conflicts AddressesChanging Base I/O Address Figure B-1 IDE Port settings for the IDE CD-ROM Interface Changing IRQ Line IDE Port IRQ LinesResolving Hardware Conflicts B-5 Troubleshooting Problems with CD-ROM DriveTroubleshooting C-2 PathMSCDEX /DMSCD001 /DMSCD002 /V /M8 Glossary CD-ROM/XATrack Logical region of a disc. Each track can Technical Support Inside U.S.A., Canada and South AmericaInside Europe FranceInside Asia Through CompuserveIf you are already a member of Compuserve If you are not a member of Compuserve valid only in U.S.A