Nextel comm IR1200 User Image Profile Commands, Registration, Reset, and Authentication Commands

Page 76

iR1200 Modem

User Image Profile Commands

Command	Usage	Action
ATz	ATz0, ATz1, or	Sets the specified image
	ATz2	as the active image.

AT&Wx	AT&W0, 1, or 2.	Writes active image to the
		specified profile

Registration, Reset, and Authentication Commands

Command	Usage	Action
AT+wvreset	AT+wvreset	Resets the modem and
		performs power cycle.

AT+wvmr	AT+wvmr=’xxxx’	Mater Resets the modem.
	(0000)

AT+wvcsk	AT+wvcsk=’xxxx’	Changes authentication
	(0000)	service key.

AT+wvrsk	AT+wvrsk=’xxxx’	Resets the service key to
	(0000)	all 0’s.

AT+WPDEREG	AT+WPDEREG	Forces modem to
		deregister.

AT+WPREG	AT+WPREG	Forces mode to register

Network Status Commands

Command	Usage	Action
66		nextel.com

Image 76

Contents Administrator’s Guide General Page Table of Contents Circuit Switched Data Modem Configuration Windows NT Saving AT Settings GPS Default Parameters Registers Pacemakers Hearing Aids Please Read Safety Notice on Before using the iR1200 Modem Page Table of Figures Table of FiguresNextel.com FCC Compliance Declaration of ConformityIR1200 Modem Required Components How to OrderDescription Online Documentation Using This Guide IntroductionWelcome to Nextel Nextel CoverageNextel Customer Care Overview General OverviewModem Operating Modes Modem ConfigurationsIR1200 Rugged Modem IR1200 GPS-Enabled Modem Rear Panel of iR1200 Rugged ModemModem Specifications LEDExternal LED IR1200 Modem Connecting the Modem Getting StartedCabling Diagram Fixed Environment Communication Indicators Signal Color IndicationCTS Packet Data StatusIR1200 Modem Installing iDEN Packet Data Applet Hardware and Installation RequirementsBefore You Begin Download Software InstructionsWindows 95/98/ME Click Next on the iDEN Packet Data Applet Setup screen ComputerProgram will check the communication settings and attempt Windows NT Click Next on the iDEN Packet Data Applet Setup screen Modem Installation Finish window opens. Click Finish Installing iDEN Packet Data Applet Multiple Baudrate should be unchecked Baud Rate 19200 bps Windows Click Next on the iDEN Packet Data Applet Setup screen That your modem is connected and click Next Multiple Baudrate should be unchecked Baud Rate 19200 bps Click Cancel to close the Make New Connection window Setting Up Windows ComponentsVerify Dial-Up Networking Verify TCP/IP Protocol Installation Click OK to close the Select Network Protocol window Windows NT/2000 Installing the Dial-Up Adapter Settings Select Control PanelConnection wizard. Click Next Modem Configuration Windows 95/98/ME Manual Modem ConfigurationInstall the Modem Configure the Modem Driver Use Flow Control Hardware RTS/CTS Click OK to close the Advanced Connection Settings windowCreate a Dial-up Networking Connection Modem Configuration Windows NT Under Type of Dial-Up Server, select PPPModem Installation Finish window opens. Click Finish Configure the Modem Driver Wizard Finish window opens. Click Finish Modem Configuration Windows Edit entry and modem properties from the drop-down listCreate and Configure a Dial-up Networking Connection Nextel.com Modify Dial-up Connection Parameters IR1200 Modem Modem Profiles and Settings HyperTerminal Setup Connection Description screen appearsBits Per second Data Bits Opening a HyperTerminal Session Parity None Stop Bits Flow Control HardwareWindows 2000/XP/Windows Windows NTRestore Factory Defaults Configuring With AT CommandsModem Initialization Activate DCD Management Activate DTR MonitoringSet Computer’s IP Address Select iDEN Packet Wireless Data Select Slip or PPPMobile IP Activation Mobile IP Authentication KeyMobile IP Home Agent Address Mobile IP Security Parameter Index SPI Mobile Node IP Prefix LengthSaving AT Settings Header CompressionGPS Default Parameters IR1200 Modem General AT Commands AT CommandsCommand Usage Action Registration, Reset, and Authentication Commands User Image Profile CommandsNetwork Status Commands Other Useful AT Commands CommandCommand Mode Echo AnswerDial Request Modem Information Hang-upGo Online Pulse Dialing Quiet ModeTone Dialing Verbose Result Codes Extended Result CodesRestore User Defaults DCD BehaviorCommand&F Restore Factory DefaultDTR Behavior Command&K Command&VLocal Flow Control Traditional Display Current Parameter ValueCommand&ICF Command+IFCLocal Character Framing Local Flow Control PccaDTE Local Data RateLock/Unlock the DCE Change the DCE’s PINCommand +WS175 Packet Data Sleep TimerCommand+WV312 Command+WV301 Command+WV300Select Mobile IP Client Command +WV302 Mobile IP Session TimerDTE IP Address Command+WPNEI Command+WV311DTE IP Address Prefix Length Data EncryptionCommand +WS45 Command +WV308DTE Stack Packet Data Registration Timeout Service ClassWDS Stack Circuit Data Establishment Timeout Circuit Data Auto-AnswerCircuit Data Idle Timer Comma Dial Modifier TimerCommandS30 Nextel.com Registers RegistersProgramming the S-Register Supported S-Registers Reading an S-Register ValueRegister # Function Valid value ranges from 0 zero to 255 zero is Default value Command Dial Modifier Time Common Problems TroubleshootingSymptom Troubleshooting Tips Modem Error Messages Message ExplanationDiagnostic Commands BusyExtended Error AT Command Extended Error Result CodesCode General Description Packet Data OperationCircuit Data Operation Nextel.com Safety Notice Safe and Efficient Operation GuidelinesExposure to Radio Frequency Energy Medical and Personal Electronic DevicesHearing Aids Interference with Other Electronic DevicesOther Medical Devices Copyright and Trademark 102nextel.com Appendix a Glossary Command Mode ConfigurationData Services DefaultDifferential GPS Dial Up Networking DUNFirmware FrequencyInternet Service Provider ISP GPS AntennaGPS Processor GPS ReceiverKbps LaptopsLocal Area Network LAN Mobile IPPacket of Data Parallel PortParity Bit ProtocolService Specific Software System AdministratorRoutable IP Address Public IP Address RS-232Transmission Rate Terminal ModeUTC Offset Index Circuit data · COM1 ·112nextel.com

Related manuals

Manual 70 pages 16.26 Kb