RAD Data comm ASM-60 operation manual DIP Switch Settings, LED Indicators, Connecting to LAN

Page 40

Appendix A IR-ETH Interface Module

ASM-60Installation and Operation Manual

 

 

DIP Switch Settings

Table A-2describes functions and default settings of the DIP switch SW-1 sections.

Table A-2. DIP Switch Settings

Section

Name

Description

Default

Number

 

 

Setting

 

 

 

 

1

SQ/FD

ON – Full-duplex operation

 

 

 

OFF – Half-duplex operation

OFF

 

 

 

 

2

CMP

ON – Strips padding bits inserted in 64-byte frame

 

 

 

OFF – Transmits frames over WAN as is

OFF

 

 

 

 

3

FIL

ON – Passes only frames destined for another LAN

 

 

 

OFF – Disables LAN filter; passes all frames transparently

OFF

4(nc)

LED Indicators

Table A-3lists the IR-ETH LED indicators and describes their functions.

Table A-3. IR-ETH Bridge LED Indicators

LED

Description

Location

Color

Name

 

 

 

 

 

 

 

LINK

ON indicates good link integrity

Rear panel

Green

 

 

 

 

COLL

ON indicates collision on the attached Ethernet

Rear panel

Yellow

 

segment

 

 

 

 

 

 

RX

ON when data is received from the Ethernet

Rear panel

Yellow

 

attached segment

 

 

 

 

 

 

TX

ON when data is transmitted from the modem

Rear panel

Yellow

 

to the Ethernet segment

 

 

 

 

 

 

ERR D4

Bridge buffer overrun

On the

Red

 

 

IR-ETH board

 

 

 

 

 

Connecting to LAN

When connecting an IR-ETH interface module with the UTP option, use either a straight cable or a cross cable for the LAN connection. Use a cross cable when connecting to a port that does not implement the crossover function internally. Otherwise, use a straight cable.

Note Hubs usually do implement the crossover function internally, while network interface cards and other devices do not.

A-4

Installation and Operation

Image 40
Contents ASM-60 International Headquarters RAD Data Communications IncPage Warranty Safety Warnings Ports Safety StatusInstalling ASM-60 Setting the Internal SwitchesConnecting the Interfaces Connecting the PowerConfiguring ASM-60 Operating ASM-60Normal Indications Selecting the Data RateContents List of Figures Chapter Introduction OverviewReal Time Alarms DTE InterfaceManagement Test CapabilitiesPhysical Description D View of ASM-60ASM-60 Block Diagram Functional DescriptionTechnical Specifications Support via RJ-45 connectorIR-IP IP router via RJ-45 connector Interface 24/RS-232 TypeTransformers to the transmit and receive lines Fuse 250A, slow-blowChapter Installation and Setup Site Requirements and PrerequisitesPackage Contents Installation and SetupPerforming the Internal Settings To install ASM-60Opening the ASM-60 Case Connecting the LineClosing the ASM-60 Case Hssi Interface Connector Pinout Connecting the DTETo connect the Hssi interface To connect the AC power Installation and Setup Front Panel Indicators ASM-60 LED IndicatorsChapter Operation Name FunctionTurning On ASM-60 ASM-60 Indicator StatusTurning Off ASM-60 Control Port Interface Characteristics Chapter Management from a TerminalPreparing for the Control Session Preparing TerminalNavigating the Management Menus Initiating a Control SessionTo initiate a control session To choose an optionStarting the Control Session Terminal Management MenusTo display the Configuration menu Main MenuTo access the Display menu Displaying the ASM-60 System InformationDisplaying the ASM-60 Status To display the ASM-60 statusResetting ASM-60 To reset ASM-60Resetting ASM-60 Chapter Diagnostics Error DetectionPower-Up Self-Test AlarmsTo access the log file Working with the Log FileDisplaying the Vdsl Performance Diagnostics ASM-60 AlarmsTo display the Vdsl diagnostics Number Terminal Message Description SeverityAfter the ASM-60 power-up ASM-60 Performance Monitoring ParametersRunning the LEDs Test Running the Diagnostic TestsTo run the LEDs test Running the Diagnostic Tests IR-ETH Connector Options Appendix a IR-ETH Interface ModuleLAN ProtocolInstallation and Operation Figure A-4. IR-ETH Layout UTP OptionDIP Switch Settings LED IndicatorsConnecting to LAN Table A-2. DIP Switch SettingsAppendix B IR-ETH/QH Interface Module IR-ETH/QH ConnectorIntroduction Pin Signal Function Table B-1 RJ-45 Connector PinoutProtocol Point-to-point Data Rate Kbps to 45 Mbps Table B-2. DIP Switch Settings Setting the DIP SwitchSection Name Description Possible Settings Factory Setting Table B-3. IR-ETH/QH LED Indicators Connecting the LANLED Name Color Description Location Appendix C IR-IP Interface Module OverviewDelay Frame Connector 10BaseT UTP Shielded RJ-45Standard Conforms to Ieee 802.3/Ethernet Data Rate TopologyIR-IP DIP Switch IR-IP LEDsTable C-1. IR-IP LEDs Functions Table C-3 RJ-45 PinoutIR-IP Management Subsystem, General Accessing the IR-IP Management SubsystemIntroduction Performing Preliminary Configuration Default IP Communication ParametersOutline of Preliminary Configuration To perform the preliminary configuration procedureConnecting the Telnet Host Preliminary Telnet Host ConfigurationAssigning the Router LAN Interface Address IP Learning MechanismTo configure the IP router LAN address To view and edit the ARP table contentsAssigning a LAN IP Address to a New IR-IP Changing the LAN IP Address of a Configured IR-IP What to Do IfNo ping replies from IR-IP IP learning process is not successfulIR-IP Management Utility General Operating ProceduresStarting a Management Utility To access the Quick Setup menu Quick Setup MenuMenu Structure of Management Utility LAN IP Address LAN IP MaskWAN IP Address WAN IP MaskManagement Access Menu Default GatewayRead Protocol from DIP Switches ProtocolAdvanced Setup Menu Telnet PasswordTelnet Inactivity Timeout To access the Management Access menuTo access the Advanced Setup menu To access the Device Identification menuDevice Identification Menu Device NameInterface Parameters Menu Aging Timeout Maintenance ProtocolTo access the Protocol Parameters menu WAN Protocol Parameters Frame Relay Protocol MenuAuthentication Protocol WAN Protocol Parameters PPP Protocol MenuHeader and Control Field Compression Protocol Field CompressionPassword To Send Password To AcceptSecurity Host/Guest User Name To SendMulticast IP Menu To access the Multicast IP menuMulticast Forwarding To access the Static Groups menu To access the Device Control menuDevice Control Menu Static GroupsTotal Timeout New Software Download MenuServer IP Address File NameView Error Log Screen Resets MenuReset Device Reset LANReset WAN Configuration and ConnectionView Menu To access the ARP Tables screen To access the Multicast Groups Table screenARP Tables Multicast Groups Table ScreenTo access the Statistics menu Statistics ScreenDiagnostic Tool Ping Terminal Menu To access the Diagnostic Tools menuUsing the Ping Function To ping a hostErasing User’s Configuration To erase the user’s configurationErasing IR-IP Software Erasing Application SoftwareCase, it is recommended to turn ASM-60 off and then back on Downloading New SoftwareTo download new software Appendix C IR-IP Interface Module Erasing IR-IP Software
Related manuals
Manual 90 pages 56.08 Kb

ASM-60 specifications

The RAD Data Communications ASM-60 is a highly advanced access and service management platform designed to streamline the deployment and management of various telecommunications services. It is particularly well-suited for carrier-grade applications, offering a robust solution that meets the demands of modern communication networks. The ASM-60 integrates multiple functionalities, ensuring that service providers can efficiently manage their networks and deliver high-quality services to their customers.

One of the standout features of the ASM-60 is its versatility. It supports a wide range of technologies, including Ethernet, TDM, and IP-based services. This adaptability allows service providers to seamlessly integrate legacy systems with newer technologies, ensuring a smooth transition as networks evolve. The platform is equipped to handle both synchronous and asynchronous services, catering to diverse customer needs while maximizing operational efficiency.

Reliability is paramount in telecommunications, and the ASM-60 excels in this regard. It boasts built-in redundancy features, ensuring continuous operation even in the event of a hardware failure. The platform is designed with hot-swappable components, allowing for maintenance and upgrades without disrupting service. This characteristic makes it an ideal choice for mission-critical applications that require uninterrupted service delivery.

In terms of scalability, the ASM-60 offers a comprehensive solution for growing networks. With its modular design, service providers can easily expand their infrastructure as demand increases. This scalability ensures that organizations can effectively respond to changing market conditions and customer requirements, facilitating long-term growth.

Another significant aspect of the ASM-60 is its advanced management capabilities. The platform is equipped with a user-friendly interface that simplifies configuration, monitoring, and troubleshooting tasks. It supports various management protocols, including SNMP and Command Line Interface (CLI), enabling seamless integration with existing network management systems.

Security is also a critical consideration in the design of the ASM-60. It features multiple layers of security, including encryption and authentication protocols, to safeguard sensitive data. This commitment to security helps service providers maintain the integrity and confidentiality of their customers’ information.

In conclusion, the RAD Data Communications ASM-60 is a powerful access and service management platform that meets the diverse needs of modern telecommunications networks. With its versatility, reliability, scalability, advanced management capabilities, and robust security features, the ASM-60 is an ideal choice for service providers looking to enhance their operational efficiency and deliver top-notch services to their customers.