RAD Data comm ASM-60 operation manual Setting the DIP Switch, Table B-2. DIP Switch Settings

Page 43

ASM-60Installation and Operation Manual

Appendix B IR-ETH/QH Interface Module

 

 

 

 

 

 

 

 

 

B.4 Installation and Operation

Figure B-3shows location of the configuration DIP switch on the module’s board.

S1

8 7 6 5 4 3 2 1

ON

Figure B-3. DIP Switch Location

Setting the DIP Switch

Configure the IR-ETH/QH module by setting the DIP switch in accordance with Table B-2. The DIP switch is located on the reverse side of the IR-ETH/QH module. To change the switch settings, you must undo three screws on the board and detach the module from the main unit.

Table B-2. DIP Switch Settings

Section

Name

Description

Possible Settings

Factory Setting

 

 

 

 

 

1

NC

 

 

OFF

 

 

 

 

 

2

NC

 

 

OFF

 

 

 

 

 

3

10/100

Selects the LAN speed

ON – LAN speed is set to 100 Mbps

OFF

 

 

 

OFF – LAN speed is set to 10 Mbps

 

 

 

 

 

 

4

AN1

Controls the LAN

ON – LAN autonegotiation is disabled

 

 

 

autonegotiation

OFF – LAN autonegotiation is enabled

OFF

 

 

 

 

 

 

 

 

5

HF1

Selects the LAN mode

ON – LAN full duplex mode

 

 

 

 

OFF – LAN half duplex mode

OFF

 

 

 

 

 

6

BPR

Controls the backpressure

ON – Backpressure is enabled

 

 

 

 

OFF – Backpressure is disabled

OFF

 

 

 

 

 

7

MUL

Controls LAN to WAN

ON – Multicast messages from LAN to

 

 

 

multicasting

WAN are blocked

 

 

 

 

OFF – Multicast messages from LAN to

OFF

 

 

 

WAN are not blocked

 

 

 

 

 

 

8

BRD

Controls LAN to WAN

ON – Broadcast messages from LAN

 

 

 

broadcasting

to WAN are blocked

 

 

 

 

OFF – Broadcast messages from LAN

OFF

 

 

 

to WAN are not blocked

 

 

 

 

 

 

Installation and Operation

B-3

Image 43
Contents International Headquarters RAD Data Communications Inc ASM-60Page Warranty Ports Safety Status Safety WarningsConnecting the Power Installing ASM-60Setting the Internal Switches Connecting the InterfacesSelecting the Data Rate Configuring ASM-60Operating ASM-60 Normal IndicationsContents List of Figures Overview Chapter IntroductionTest Capabilities Real Time AlarmsDTE Interface ManagementD View of ASM-60 Physical DescriptionFunctional Description ASM-60 Block DiagramInterface 24/RS-232 Type Technical SpecificationsSupport via RJ-45 connector IR-IP IP router via RJ-45 connectorFuse 250A, slow-blow Transformers to the transmit and receive linesSite Requirements and Prerequisites Chapter Installation and SetupTo install ASM-60 Package ContentsInstallation and Setup Performing the Internal SettingsOpening the ASM-60 Case Connecting the LineClosing the ASM-60 Case Hssi Interface Connector Pinout Connecting the DTETo connect the Hssi interface To connect the AC power Installation and Setup Name Function Front Panel IndicatorsASM-60 LED Indicators Chapter OperationTurning On ASM-60 ASM-60 Indicator StatusTurning Off ASM-60 Preparing Terminal Control Port Interface CharacteristicsChapter Management from a Terminal Preparing for the Control SessionTo choose an option Navigating the Management MenusInitiating a Control Session To initiate a control sessionTerminal Management Menus Starting the Control SessionMain Menu To display the Configuration menuDisplaying the ASM-60 System Information To access the Display menuTo display the ASM-60 status Displaying the ASM-60 StatusTo reset ASM-60 Resetting ASM-60Resetting ASM-60 Alarms Chapter DiagnosticsError Detection Power-Up Self-TestWorking with the Log File To access the log fileNumber Terminal Message Description Severity Displaying the Vdsl Performance DiagnosticsASM-60 Alarms To display the Vdsl diagnosticsASM-60 Performance Monitoring Parameters After the ASM-60 power-upRunning the LEDs Test Running the Diagnostic TestsTo run the LEDs test Running the Diagnostic Tests Appendix a IR-ETH Interface Module IR-ETH Connector OptionsProtocol LANFigure A-4. IR-ETH Layout UTP Option Installation and OperationTable A-2. DIP Switch Settings DIP Switch SettingsLED Indicators Connecting to LANAppendix B IR-ETH/QH Interface Module IR-ETH/QH ConnectorIntroduction Pin Signal Function Table B-1 RJ-45 Connector PinoutProtocol Point-to-point Data Rate Kbps to 45 Mbps Table B-2. DIP Switch Settings Setting the DIP SwitchSection Name Description Possible Settings Factory Setting Table B-3. IR-ETH/QH LED Indicators Connecting the LANLED Name Color Description Location Overview Appendix C IR-IP Interface ModuleTopology Delay FrameConnector 10BaseT UTP Shielded RJ-45 Standard Conforms to Ieee 802.3/Ethernet Data RateTable C-3 RJ-45 Pinout IR-IP DIP SwitchIR-IP LEDs Table C-1. IR-IP LEDs FunctionsIR-IP Management Subsystem, General Accessing the IR-IP Management SubsystemIntroduction To perform the preliminary configuration procedure Performing Preliminary ConfigurationDefault IP Communication Parameters Outline of Preliminary ConfigurationIP Learning Mechanism Connecting the Telnet HostPreliminary Telnet Host Configuration Assigning the Router LAN Interface AddressTo configure the IP router LAN address To view and edit the ARP table contentsAssigning a LAN IP Address to a New IR-IP IP learning process is not successful Changing the LAN IP Address of a Configured IR-IPWhat to Do If No ping replies from IR-IPIR-IP Management Utility General Operating ProceduresStarting a Management Utility To access the Quick Setup menu Quick Setup MenuMenu Structure of Management Utility WAN IP Mask LAN IP AddressLAN IP Mask WAN IP AddressProtocol Management Access MenuDefault Gateway Read Protocol from DIP SwitchesTo access the Management Access menu Advanced Setup MenuTelnet Password Telnet Inactivity TimeoutDevice Name To access the Advanced Setup menuTo access the Device Identification menu Device Identification MenuInterface Parameters Menu WAN Protocol Parameters Frame Relay Protocol Menu Aging TimeoutMaintenance Protocol To access the Protocol Parameters menuProtocol Field Compression Authentication ProtocolWAN Protocol Parameters PPP Protocol Menu Header and Control Field CompressionUser Name To Send Password To SendPassword To Accept Security Host/GuestMulticast IP Menu To access the Multicast IP menuMulticast Forwarding Static Groups To access the Static Groups menuTo access the Device Control menu Device Control MenuFile Name Total TimeoutNew Software Download Menu Server IP AddressReset LAN View Error Log ScreenResets Menu Reset DeviceReset WAN Configuration and ConnectionView Menu Multicast Groups Table Screen To access the ARP Tables screenTo access the Multicast Groups Table screen ARP TablesStatistics Screen To access the Statistics menuTo access the Diagnostic Tools menu Diagnostic Tool Ping Terminal MenuTo ping a host Using the Ping FunctionErasing Application Software Erasing User’s ConfigurationTo erase the user’s configuration Erasing IR-IP SoftwareCase, it is recommended to turn ASM-60 off and then back on Downloading New SoftwareTo download new software Appendix C IR-IP Interface Module Erasing IR-IP Software
Related manuals
Manual 90 pages 56.08 Kb

ASM-60 specifications

The RAD Data Communications ASM-60 is a highly advanced access and service management platform designed to streamline the deployment and management of various telecommunications services. It is particularly well-suited for carrier-grade applications, offering a robust solution that meets the demands of modern communication networks. The ASM-60 integrates multiple functionalities, ensuring that service providers can efficiently manage their networks and deliver high-quality services to their customers.

One of the standout features of the ASM-60 is its versatility. It supports a wide range of technologies, including Ethernet, TDM, and IP-based services. This adaptability allows service providers to seamlessly integrate legacy systems with newer technologies, ensuring a smooth transition as networks evolve. The platform is equipped to handle both synchronous and asynchronous services, catering to diverse customer needs while maximizing operational efficiency.

Reliability is paramount in telecommunications, and the ASM-60 excels in this regard. It boasts built-in redundancy features, ensuring continuous operation even in the event of a hardware failure. The platform is designed with hot-swappable components, allowing for maintenance and upgrades without disrupting service. This characteristic makes it an ideal choice for mission-critical applications that require uninterrupted service delivery.

In terms of scalability, the ASM-60 offers a comprehensive solution for growing networks. With its modular design, service providers can easily expand their infrastructure as demand increases. This scalability ensures that organizations can effectively respond to changing market conditions and customer requirements, facilitating long-term growth.

Another significant aspect of the ASM-60 is its advanced management capabilities. The platform is equipped with a user-friendly interface that simplifies configuration, monitoring, and troubleshooting tasks. It supports various management protocols, including SNMP and Command Line Interface (CLI), enabling seamless integration with existing network management systems.

Security is also a critical consideration in the design of the ASM-60. It features multiple layers of security, including encryption and authentication protocols, to safeguard sensitive data. This commitment to security helps service providers maintain the integrity and confidentiality of their customers’ information.

In conclusion, the RAD Data Communications ASM-60 is a powerful access and service management platform that meets the diverse needs of modern telecommunications networks. With its versatility, reliability, scalability, advanced management capabilities, and robust security features, the ASM-60 is an ideal choice for service providers looking to enhance their operational efficiency and deliver top-notch services to their customers.