Cisco Systems SFS 7008 manual About the Field Replaceable Units, Power Supply Modules

Page 35

35

3

Managing Individual Components

This chapter describes how to install the Field Replaceable Units (FRUs) in the Topspin 270 system.

About the Field Replaceable Units

The following Field Replaceable Units (FRUs) are a part of the Topspin 270 chassis:

“Power Supply Modules” on page 35

“Fan Tray Modules” on page 39

“Fabric Controllers” on page 42

“Line Interface Management Modules (LIM)” on page 45

“Management Interface Modules” on page 49

“Chassis ID Modules” on page 50

Power Supply Modules

About the Power Supply Modules

The Topspin 270 power supply units are hot-swappable. Only one power module is necessary to power the unit; however, two power supplies are recommended for redundancy.

You can add a second module without powering off the chassis. If you have two power supply units installed, you can remove one of them without removing power from the chassis.

About a Failed Power Supply

If you believe a power supply module has failed, contact technical support.

Do not remove a failed power supply unless you have a new power supply to install immediately, or a blanking panel to place over the open bay as overheating may occur.

Image 35
Contents Part Number OL-7725-01 Product ID Page Regulatory Notices Vii Managing Individual Components Monitoring the Topspin 270 System 107 Electrical Cautions FCC Statement Safety InformationViii General Cautions Contact InformationPage Hot Standby System ArchitectureHardware InfiniBand ConnectivityFlexibility Hi-AvailabilityFabric Diagram of the ChassisAbout the Topspin 270 Chassis Non-Blocking Architecture2Back Chassis View 3Chassis Slot Numbering in Front Non-port Side Chassis Slot NumberingLEDs DimensionsPower Supplies ConnectionsManagement Interface Modules Fan TraysNode Slot Fabric Controller ModulesNode and Core Slots Master/Slave and Standby RolesHow the Chassis ID is Used Rack AlarmLine Interface Modules LIM Chassis ID ModuleAdministrative Features Prepare the Physical Environment for Topspin 270 System Prepare the SiteRead the Cautionary Statements Requirements Rack Mount InstallationMount the Topspin 270 Chassis in a Rack 2Unscrew Extra Rack Ears from the Chassis 3Chassis Set onto Shelf 5Use Appropriate Screws to Attach Rack Ears to Rails Install Optional HA ComponentsAttach a Serial Console Cable to a PC or Terminal Connect Management DevicesConnect an Ethernet Cable to the Ethernet Management Port Recommended Management ConfigurationPower on the Chassis 8Power Jack Locations Configure Basic ConnectivityAssigning an Address Dynamically Topspin-270config#interface mgmt-ethernetTopspin-270#copy running-config startup-config Assigning an Address StaticallyConnect Network Devices About ConnectorsManage the System Connecting InfiniBand DevicesLaunch Chassis Manager Optional Launch the Chassis ManagerPrepare Your Device 10Web Browser Window Optional Install the Element Manager GUI About the Field Replaceable Units Power Supply ModulesAbout the Power Supply Modules About a Failed Power SupplyLocating the Power Supply Module Removing a Power Supply ModulePower Cord back Power Supply front 3Pulling the Power Supply Module from the Bay Installing a New Power Supply ModuleAbout a Failed Fan Tray Fan Tray ModulesAbout the Fan Tray Modules Removing a Fan Module5Loosening Captive Screws 7Pushing Fan Module into Slot Installing a Fan ModuleRemoving a Fabric Controller Fabric ControllersAbout the Fabric Controllers 9Loosen Captive Screws Before Removing Upgrading the Controller Card Installing a Fabric ControllerRemoving a LIM Card Line Interface Management Modules LIMAbout LIM Cards 12Removing a Pinch-Type Connector 14Loosen the Captive Screws 17Closing the LIM Module Levers Installing a LIM ModuleAbout a Failed Management Interface Module Management Interface ModulesAbout Management Interface Modules Removing a Management Interface ModuleRemoving a Chassis ID Module Installing a Management Interface ModuleChassis ID Modules About Chassis ID Modules20Loosen the Captive Screws Installing a Replacement Chassis ID Module Upgrading a Topspin 270 with the CLI Upgrade all Cards in a ChassisUpgrading a Topspin 270 with Element Manager Select Maintenance File ManagementSelect Maintenance Boot Config Upgrading a Topspin 270 with the Chassis Manager Upgrading an Individual Controller CardUpgrading a Controller Card with the CLI Show the standby Controller card Upgrading a Node Card with the CLI Upgrading Individual Node CardsUpgrading a Node Card with Element Manager 5Copy the .img File to Server Switch6Watching the File Copy Progress 8Disable and Enable the Node Cards Upgrading Node Cards with the Chassis Manager Page Interpreting the Front Panel LEDs Monitoring the Topspin 270 SystemInterpreting the System Status LED System-Wide Status LEDLocating the System-Wide Status LED Locating the Power Supply LEDs Power Supply LEDs3Power Supply Identify LED Interpreting the Power Supply LEDsInterpreting the Fan LEDs Fan LEDsLocation Interpreting the Fabric Controller LEDs Fabric Controller LEDsManagement Interface Module LEDs Interpreting the Back Panel LEDs6Management Interface Module LEDs Interpreting the Management Interface LEDsFan Tray Module Status LEDs Master Management Connection Status LED Chassis ID LEDsInterpreting the LIM Status LEDs LIM Status LEDsInfiniBand Port LEDs Interpreting the InfiniBand Port LEDs Monitoring the System with Chassis ManagerMonitor the Device Device Rear View and the Device Front View appear 11Chassis Manager 270 Device Front View 12Chassis Manager Cards Window Monitor the Cards13Chassis Manager Ports Window Monitor the InfiniBand Ports14Chassis Manager Port Properties Dialog Box Monitor the Power SuppliesMonitor the Fans 15Chassis Manager Power Supplies Window17Chassis Manager Sensors Window Monitor the TemperatureInterpreting the Summary Tab Monitoring the System with Element ManagerInterpreting the Sensors Tab Interpreting the Power Supplies TabInterpreting the Fans Tab Monitor the Fans Monitor the Power SuppliesTopspin-270show power-supply Monitor the System With the CLIShow sensor Monitor the SensorsPage Self Tests About Diagnostic TestsLED Tests Run a Card Self-Test Topspin-270#show diagnostic cardRun Card Tests Example of completed test Topspin-270# more sysloghwiflog Run Chassis TestsRun a Chassis Standard Test Topspin-270config#diag chassis test standardTopspin-270#show diag post Run Fan TestsRun a Self-Test on a Fan Enter the diag fan id command Topspin-270#show diag fru-error Run Power Supply TestsRun a LED Test on the Power Supply Topspin-270#show diag power-supply Run a Self-Test on a Power SupplyTopspin-270#show power-supply Topspin-270#show diag fru-error Topspin-270#more sysloghwiflog Displaying Hardware ErrorsTopspin-270#show diagnostic post Topspin-270#show diagnostic fru-error Error Types101 102 Chassis and Management Interface Specifications and Compliance CertificationsAcoustics Electrical SpecificationsSafety EMC/ImmunityProduct Markings 106 Index

SFS 7008 specifications

The Cisco Systems SFS 7008 is a powerful storage solution designed to address the diverse and demanding needs of modern data environments. As organizations continue to generate and store vast amounts of data, the SFS 7008 delivers robust performance and scalability, making it a key player in high-performance computing (HPC) and enterprise data centers.

One of the main features of the SFS 7008 is its exceptional scalability. It supports a broad range of storage capacities, allowing organizations to easily expand their storage as their data requirements grow. This scalability ensures that businesses can adapt to changing workloads without significant disruption or the need for a costly overhaul of their storage infrastructure.

The SFS 7008 utilizes advanced technologies to optimize performance and efficiency. It employs a high-speed interconnect architecture that enables faster data transfer rates across multiple nodes. This feature is particularly beneficial for applications that require rapid access to large datasets, such as big data analytics and machine learning workloads. Moreover, the system supports multiple data protocols, including NFS, SMB, and iSCSI, making it versatile enough to handle various types of applications in diverse environments.

Another notable characteristic of the SFS 7008 is its data management capabilities. It features built-in tools that facilitate data replication, snapshotting, and backup, ensuring that organizations can maintain data integrity and availability at all times. These tools are essential for disaster recovery and provide peace of mind for businesses that rely on critical data for their operations.

Furthermore, the SFS 7008 is designed with security in mind. The system incorporates advanced security features that protect sensitive data from unauthorized access and breaches. These include encryption options and comprehensive access control mechanisms, allowing administrators to implement strict governance policies for data usage.

In summary, the Cisco Systems SFS 7008 stands out as a leading storage solution with its scalability, performance optimization, versatile protocol support, robust data management features, and enhanced security measures. As businesses continue to navigate the complexities of data management in today’s digital landscape, the SFS 7008 provides a reliable foundation for their storage needs, enabling them to harness the full potential of their data. This makes it an ideal choice for organizations seeking a future-proof storage solution.