Motion Computing LE1600TC manual Charging the Battery, To charge the battery, Swapping the Battery

Page 38

Chapter 2 Using Your Motion Tablet Client

Charging the Battery

When you connect the Tablet Client to AC power with a battery attached, the system automatically charges the battery until it reaches full charge. If two batteries are attached, the primary battery charges first, followed by the secondary battery. The charging sequence is staggered to ensure that both batteries become fully charged at nearly the same time. The standard battery charges to the 80% level, followed by the Extended Battery charging to the 80% level. Then each battery charges for a short interval until both reach 100%.

The Battery Status LED is on the Tablet Client flashes amber when the battery is at a critically low level and changes to solid amber while charging. When the battery is fully charged, the Battery Status LED is solid blue.

WARNING: To avoid injury, keep the battery within the recommended temperature range when charging it. Wait until it cools to room temperature before recharging it in the Tablet Client or the battery charger. For more information, see the Safety and Regulatory Guide shipped with your Tablet Client or the documentation that came with the battery charger. Or go to www.motioncomputing.com/ support to view these documents.

To charge the battery:

1.Plug the AC adapter into the Tablet Client.

2.Then plug the AC adapter cable into a wall outlet or power strip. (Completely recharging the battery may take up to two hours, although the battery reaches an 80% charge in much

less time.)

Swapping the Battery

You can swap the Standard Battery while the system is powered on, with or without having the Tablet Client plugged into an AC power outlet.

CAUTION: To avoid damage to the Tablet Client, install only Motion Computing batteries, which are specially designed for the Tablet Client.

To swap the battery:

1.If the Tablet Client is running, open the Motion Dashboard and tap Stand By. The Tablet Client immediately goes into the Stand By state.

2.Alternatively, go to Start > Turn Off Computer.

3.Do one of the following:

•If you are logged on to a domain: When the Turn Off Computer window appears, tap Stand By from the drop-down list.

NOTE: Here is information about putting the Tablet Client in

Stand By mode to swap the battery:

30Motion Computing LE1600TC Tablet Client User Guide

Page 37 Page 39
Image 38
Page 37 Page 39
Contents LE1600TC Copyright Information Table of Contents Care and Maintenance Appendix a Troubleshooting and Support Vi Motion Computing LE1600TC Tablet Client User Guide About This User Guide Viii Motion Computing LE1600TC Tablet Client User Guide Chapter Getting Started with Your Tablet Client Getting Started with Your Tablet Client Helpful Hints for Using Pen and Ink Pen UsageOpen the Motion Dashboard Using Your Motion Tablet and User GuideOpen the Motion Dashboard Fingerprint Reader Tablet Client DisplayTablet Client View AnywhereTM Display Option Motion Battery Pack Motion AC AdapterOpens the Motion Dashboard RJ-45/LAN Front Panel Buttons Front Panel LEDsBattery Status LEDs Front Panel Battery Status LED Battery LED ActionDescription of Left-Side of Tablet Client Description of Right-Side of Tablet Client Description of Docking Side of Tablet ClientMotion Dashboard Motion Dashboard Features Motion Dashboard Features Description Client Applications Citrix MetaFrame Access Program NeighborhoodMotion Security Center Browser Microsoft Internet ExplorerMotion Computing LE1600TC Tablet Client User Guide Getting Started with Your Tablet Client Configuring Tablet and Pen Settings To configure the tablet and pen settingsTo calibrate your digitizer pen Select Start Control Panel Calibrating Your Digitizer PenRitePen Software Application Motion Computing LE1600TC Tablet Client User Guide Using the On Screen Keyboard Motion Dashboard Audio System ControlsSetting Fixed Display Brightness ALS Off Adjusting Display Settings and Screen BrightnessSetting Dynamic Display Brightness ALS On To set the Dynamic display brightness to ALS OnTo turn the display on and off To change the display orientation using the Rotation buttonTurning the Display On and Off Changing Display OrientationTo connect the Tablet Client and a monitor or projector Setting Up a Mirrored DisplayMirroring or Extending Your Display Setting Up an Extended Display Configuring Your Power Management Settings Reading Battery Power from the Tablet Client Display Reading Battery Power from the Power Meter Using Your BatteriesReading Battery Power from Motion Dashboard Swapping the Battery Charging the BatteryTo charge the battery To swap the batteryHelpful Hints Battery and Power Management Disposing of Used BatteriesSecurity Features Settings Fingerprint Reader and Motion OmniPass Manage OmniPass Users and Settings Other OmniPass Set Up Functions Fingerprint ReaderUsing Motion OmniPass Security and the Fingerprint Reader Helpful Hints for Successful Fingerprint CapturesCapturing a Fingerprint Using Your Motion Tablet Client Motion Computing LE1600TC Tablet Client User Guide Capturing a Second Fingerprint Later Configuring Advanced OmniPass FeaturesMotion OmniPass Manage OmniPass Users and Settings Replacing Password Logons Motion OmniPass Change User SettingsChange System Settings To replace password logonsTo log on to a remembered site Configuring Strong Logon SecurityLogging Onto a Remembered Site Exporting Your User ProfileTap the checkbox Enable strong logon security To configure Strong Logon SecurityTap Change OmniPass System Settings More Information About the Infineon Security SolutionMicrosoft Security Center Windows Security System Components OverviewPop-up blocker in Internet Explorer Setting Bios Passwords Using Windows SecuritySetting the Windows Operating System Password Setting a Bios System PasswordTo create a disk drive password To set a Bios system passwordDisk Drive DD Password To clear the Tablet Client PhoenixBIOS security Clearing Tablet Client SecuritySpeech Motion Speak Anywhere Technology Using Motion Dashboard Directional ControlsTo set up the skew angle Open the Motion Dashboard PC Cards To install and remove a PC CardHelpful Hint for Dictating and Recording SD CardsUSB Ports VGA ConnectorDocking Connector Speaker PortWi-Fi 802.11 Wireless Connections Enabling/Setting Up a Wireless Connection Through DashboardBluetooth Wireless Connections To begin using BluetoothBluetooth Device Connection Process Accessing BluetoothTo open the Bluetooth Settings menu Using the Bluetooth Application Add New Connection WizardUsing Your Motion Tablet Client Motion Computing LE1600TC Tablet Client User Guide Important Actions To Perform If the Device Is Not Discovered To open the Motion DashboardHelpful Hints for Using Bluetooth Wireless Using Infrared Wireless Connections Accessing Image Transfer Button On screenKeyboard SAS buttonChapter Care and Maintenance General CareReplacing the Pen Tips Caring for the Standard and View Anywhere DisplaysCaring for the Motion Digitizer Pen To replace the pen tipsTraveling by Air FAA Wireless Air Travel RequirementOrdering New Pens Other Travel Hints Appendix a Troubleshooting and Support Display INTERFACE/PORTS DVD/CD RW How should I clean the View Anywhere display screen? Can I make the battery charge last longer?What’s the best way to clean the standard display screen? Will scratches affect the display/digitizer’s performance?How do I adjust the Tablet Client for left-handed use? Standard and Extended Warranty and Insurance Programs
Top Page Image Contents