Motion Computing AB52242 Helpful Hints Battery and Power Management, Disposing of Used Batteries

Page 39

Chapter 2 Using Your Motion Tablet Client

•When choosing Stand By, the Tablet Client is designed to maintain your system for up to 30 seconds while you swap the battery.

•However, you may have less than 30 seconds if you are running a number of programs that drain power faster.

•You should save any data before putting the system in Stand By to swap the battery.

4.Tap Stand By. The Tablet Client opens a dialog box stating that it is “preparing to standby.”

5.Wait until the system shuts down. In Stand By, the Power LED flashes.

6.Slide the battery release latches on the back of the Tablet Client toward the center and lift the battery upward to remove it.

7.Insert the new battery until you hear the left latch click, which ensures the new battery is correctly seated. Slide the right latch fur- ther to the right to lock it in place. Check to make sure the latches are fully seated.

Disposing of Used Batteries

The Tablet Client contains a Lithium-ion (Li-ion) battery that should be disposed of at a hazardous materials recycling center when it is no longer serviceable. Do not throw it in a waste receptacle where it will be sent to a landfill.

Helpful Hints: Battery and Power Management

•Use AC power when available to lengthen the battery’s usable life. The battery will charge automatically as you run on AC power, so leave the battery in the Tablet Client while you are working.

•Use AC power when installing software or writing to a CD, and for opti- mal battery life, when using a CD or DVD player.

•When using battery power, if you leave the Tablet Client unattended, place the system in Stand By mode.

•Keep in mind that the display, processor, PC Cards, SD cards, wireless cards, and accessory drives all draw on the battery, so adjust properties and disable unused accessories and PC Cards when operating on bat- tery power.

•When using battery power, adjust the power mode and display bright- ness to lower settings to prolong the battery life.

•Turn off all wireless devices through the Motion Dashboard when not being used.

•Enable the Ambient Light Sensor (ALS) through Motion Dashboard. See the section “Adjusting Display Settings and Screen Brightness” on page 23.

Motion Computing LE1600TC Tablet Client User Guide 31

Page 38 Page 40
Image 39
Page 38 Page 40
Contents LE1600TC Copyright Information Table of Contents Care and Maintenance Appendix a Troubleshooting and Support Vi Motion Computing LE1600TC Tablet Client User Guide About This User Guide Viii Motion Computing LE1600TC Tablet Client User Guide Chapter Getting Started with Your Tablet Client Getting Started with Your Tablet Client Pen Usage Helpful Hints for Using Pen and InkUsing Your Motion Tablet and User Guide Open the Motion DashboardOpen the Motion Dashboard Tablet Client Display Tablet Client View AnywhereTM Display OptionFingerprint Reader Motion AC Adapter Motion Battery PackOpens the Motion Dashboard RJ-45/LAN Front Panel LEDs Front Panel ButtonsFront Panel Battery Status LED Battery LED Action Battery Status LEDsDescription of Left-Side of Tablet Client Description of Docking Side of Tablet Client Description of Right-Side of Tablet ClientMotion Dashboard Motion Dashboard Features Motion Dashboard Features Description Browser Microsoft Internet Explorer Citrix MetaFrame Access Program NeighborhoodMotion Security Center Client ApplicationsMotion Computing LE1600TC Tablet Client User Guide Getting Started with Your Tablet Client To configure the tablet and pen settings Configuring Tablet and Pen SettingsCalibrating Your Digitizer Pen RitePen Software ApplicationTo calibrate your digitizer pen Select Start Control Panel Motion Computing LE1600TC Tablet Client User Guide Motion Dashboard Audio System Controls Using the On Screen KeyboardTo set the Dynamic display brightness to ALS On Adjusting Display Settings and Screen BrightnessSetting Dynamic Display Brightness ALS On Setting Fixed Display Brightness ALS OffChanging Display Orientation To change the display orientation using the Rotation buttonTurning the Display On and Off To turn the display on and offSetting Up a Mirrored Display Mirroring or Extending Your DisplayTo connect the Tablet Client and a monitor or projector Setting Up an Extended Display Configuring Your Power Management Settings Reading Battery Power from the Tablet Client Display Using Your Batteries Reading Battery Power from Motion DashboardReading Battery Power from the Power Meter To swap the battery Charging the BatteryTo charge the battery Swapping the BatteryDisposing of Used Batteries Helpful Hints Battery and Power ManagementSecurity Features Settings Fingerprint Reader and Motion OmniPass Manage OmniPass Users and Settings Fingerprint Reader Other OmniPass Set Up FunctionsHelpful Hints for Successful Fingerprint Captures Using Motion OmniPass Security and the Fingerprint ReaderCapturing a Fingerprint Using Your Motion Tablet Client Motion Computing LE1600TC Tablet Client User Guide Configuring Advanced OmniPass Features Motion OmniPass Manage OmniPass Users and SettingsCapturing a Second Fingerprint Later To replace password logons Motion OmniPass Change User SettingsChange System Settings Replacing Password LogonsExporting Your User Profile Configuring Strong Logon SecurityLogging Onto a Remembered Site To log on to a remembered siteMore Information About the Infineon Security Solution To configure Strong Logon SecurityTap Change OmniPass System Settings Tap the checkbox Enable strong logon securityWindows Security System Components Overview Pop-up blocker in Internet ExplorerMicrosoft Security Center Setting a Bios System Password Using Windows SecuritySetting the Windows Operating System Password Setting Bios PasswordsTo set a Bios system password Disk Drive DD PasswordTo create a disk drive password Clearing Tablet Client Security To clear the Tablet Client PhoenixBIOS securityUsing Motion Dashboard Directional Controls Speech Motion Speak Anywhere TechnologyTo set up the skew angle Open the Motion Dashboard SD Cards To install and remove a PC CardHelpful Hint for Dictating and Recording PC CardsSpeaker Port VGA ConnectorDocking Connector USB PortsEnabling/Setting Up a Wireless Connection Through Dashboard Wi-Fi 802.11 Wireless ConnectionsTo begin using Bluetooth Bluetooth Wireless ConnectionsAccessing Bluetooth To open the Bluetooth Settings menuBluetooth Device Connection Process Add New Connection Wizard Using the Bluetooth ApplicationUsing Your Motion Tablet Client Motion Computing LE1600TC Tablet Client User Guide To open the Motion Dashboard Important Actions To Perform If the Device Is Not DiscoveredHelpful Hints for Using Bluetooth Wireless Using Infrared Wireless Connections Accessing Image Transfer SAS button On screenKeyboard ButtonGeneral Care Chapter Care and MaintenanceTo replace the pen tips Caring for the Standard and View Anywhere DisplaysCaring for the Motion Digitizer Pen Replacing the Pen TipsFAA Wireless Air Travel Requirement Ordering New PensTraveling by Air Other Travel Hints Appendix a Troubleshooting and Support Display INTERFACE/PORTS DVD/CD RW Will scratches affect the display/digitizer’s performance? Can I make the battery charge last longer?What’s the best way to clean the standard display screen? How should I clean the View Anywhere display screen?Standard and Extended Warranty and Insurance Programs How do I adjust the Tablet Client for left-handed use?
Top Page Image Contents