Axis Communications 700 user manual OlXg D77 User’s Manual Configuring the Axis

Page 50

OlXg D77 User’s Manual

Section 3: Configuring the AXIS 700

49

 

 

 

 

If you permit the users to add temporary profiles, the five most

 

 

 

recently added ones will appear in the list. You can make

 

 

 

temporary profiles permanent by clicking Make Permanent

.

 

To change the default profile settings, e.g. the paper size, click

 

 

 

Profile Defaults >> and change the settings.

 

 

To to make sure that all pages are in upright position when

 

 

 

scanned double sided, click PDF Options >> and change the

 

 

 

settings.

 

 

If you need to restore the predefined profiles, click Restore

 

 

 

Predefined Profiles. Note that all your current profiles will be

 

 

 

lost.

 

va

ο Not all combinations of settings are possible. If you try to use a

 

combination that is not valid, the AXIS 700 will display an error message.

Apart from the predefined profiles above we also recommend two profiles which generate PDF documents. The first recommended profile is for text documents. To create this profile, copy the Text profile and then change the Format-Compression field to PDF- CCITT G.4. The second recommended profile is a color profile suited for pictures and mixed text/pictures. Copy the Color high profile and change the Format-Compression field to PDF-JPEG.

Image 50
Contents E rs M a n u a l v 1 User’s Manual OlXg D77 User’s ManualAxis 700 User’s Manual Revision Copyright Axis Communications AB, 1997OlXg D77 User’s Manual Preface Dwy OlXg D77 User’s Manual Table of Contents Huv OlXg D77 User’s Manual Introduction Zny SII t yXyyy GywXxXxy Kyv gyAuy Axis 700 over the network using FTPThan the other way around GywXx OlXg D77 User’s Manual Basic Installation Guxux xyyGywPuXu Puw duy Duy$,6 9HUVLRQ Up and Down keys scroll and select menu options Cancel keyAy The Menu key scrolls the menu Enter key RuwyChanges to the network configuration Scanning device documentation on how to do thisAlways consult the Network Administrator before making Turn off the Axis 700 by unplugging the power supplyAfter a few seconds this display will be shown Where x.xx is the software version numberPower up the Axis 700. Press Menu Press Enter to edit the subnet mask Press Enter to edit the default router addressPress Enter to edit the IP address Byy Press Menu once more to display the final instructionsJyy From the Axis 700 control panelXd Oxx CyyzSux SWRdAu bu IWRd Your Axis 700. Type arp -a to display the ARP table Host will return ‘Reply from 172.19.2.254...’ or a similarCommunication is established Ether for Ethernet networks, e.g. arp -s ether spserv IbXl u cg69IP address and verify the communication Ethernet address Host name Where Typically performed using the command bootpd -aIcchd Required by your systemHttp//172.19.2.254 GywPuXu OlXg D77 User’s Manual Configuring the Axis Network protocol settingsGywRlXg D77 This brings you to the Axis 700 HomeOlXg D77 User’s Manual Configuring the Axis Click Network Settings Oxxy Auhd0Tyu Sy jyGywRlXg D77 OlXg D77 User’s Manual Configuring the Axis T4hd0 From this page you can set the following parametersTu Oxxy =countrycode Description, Transfer method and Destination fields are Configuration parameters are described in The ParameterLast five fields only apply to file destinations. Mandatory for all destination types. For FTP destinations,Destination list on the Axis 700 control panel Table. Click Detailed to view the detailed settingsDestination Name is the text that will appear Can make these temporary destinations permanent by clickingMail destinations Mail addresses using the Smtp protocolT4uy GywRlXg D77 Will be stored When the URL is sent to an e-mail destinationIf z Tu Information Click Destination Defaults to change the default valuesSyyzu Filenamesequencenumber.fileextension, e.g. image001.tif GywRlXg D77 Iy c Axis 700 interface Most needs. This table lists the predefined profilesProfile Name list to edit an existing profile Click New Profile to add a new profile to the listOlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Using the Axis Gywi Xg D77 T4uKyv P Gwu ifDestinations on Axis 700 display shows Send to xxxxxx when it isOptionally, press Menu To change the default settings for Perform these instructions from the Axis 700 control panelSetting Several separate pages or stacks of papersOther separation pages will be ignored Yv gyu gyyCanon DR-3020 scanner. a job separation sheet inserted in a Sharp AR-seriesLine Interface Administrator might not allow users to add temporaryDown or re-started Enter the name or IP address of your Axis 700 onOlXg D77 User’s Manual Using the Axis Depending on your scanning device, some profiles may not be This table outlines when to use the predefined profilesDefault profile is Text Black/white scanning devices, unless they can do gray-scaleDu g Maintained by the AdministratorDefault paper size is Letter SyxExample Several separate pages Owuyuxy XuxCRf uw OlXg D77 User’s Manual Using the Axis Owy Axis 700 User’s Manual Appendix a Troubleshooting FTPOG h Axis 700 User’s Manual Tml This table lists a summary of error conditions Gu Xxu By Xxwu czzCDB Flatbed only Work. Attached scanner id is displayed in the event log Event log is displayed Axis 700 Home Page is displayed. Click AdministrationField and press Enter Axis 700 User’s Manual Appendix B Ldap Ldap allows resources and services to be selected with easeAccessed with location-independence System looks likeAxis 700 User’s Manual Dwwu Objectclass=personcn=john Only want to retrieve entries of the people class, withCould be achieved with the following filter Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual As in the table below OlXg D77 User’s Manual Appendix C The Parameter ListGives a brief description of the parameter DefaultRouter ORG hURL Smtp = Destination name END Axis web site on how to join the AxisNews Compare against the latest software issues from AxisWhere you can download the latest versions of the software OlXg D77 User’s Manual Appendix D Updating the SoftwareOSG i y OlXg D77 User’s Manual Appendix D Updating the Software OSG i y Simple Mail Transfer Protocol Smtp server Client Web browser, and at least one of these protocolsFile Transfer Protocol FTP server Netscape Navigator 3.0 or higherOuu 12V DC 36VA, via external power unit Axis PS-C or Number is limited by the Eeprom memory. If using Ldap orSoftware over the network using FTP 12V DC 13,2VA, via external power unit Axis PS-EOuu OlXg D77 User’s Manual Appendix F Glossary Axis 700 User’s Manual OlXg D77 User’s Manual Appendix F Glossary 100 OlXg D77 User’s Manual Index 101 Http OlXg D77 User’s Manual Index 103 Dhcp Rarp
Related manuals
Manual 6 pages 3.58 Kb