Axis Communications 700 user manual Line

Page 60

OlXg D77 User’s Manual	Section 4: Using the AXIS 700	59

e z

If you want to send a scanned document to an e-mail destination that does not appear in the destination list on the AXIS 700 display, you can add it temporarily from the Web browser interface.

va	ο The Administrator might not allow users to add temporary e-mail
		destinations.
	1.	Start the Web browser.
	2.	Enter the name IP address of your AXIS 700 on the location/address
		line:
		Example

		http://172.19.2.254

	3.	This brings you to the AXIS 700 Home Page. Click Destinations.

4.The table lists the available destinations. Click

New Destination >> and specify the settings for the new destination.

5.Click OK to save the destination temporarily. Note that only the five most-recently added temporary destinations will appear in the destination list. Contact your Administrator if you want to add a destination permanently.

Image 60

Contents E rs M a n u a l v 1 User’s Manual OlXg D77 User’s ManualAxis 700 User’s Manual Revision Copyright Axis Communications AB, 1997OlXg D77 User’s Manual Preface Dwy OlXg D77 User’s Manual Table of Contents Huv OlXg D77 User’s Manual Introduction Zny SII t yGywXx XxyXyyy Kyv gyAxis 700 over the network using FTP Than the other way aroundAuy GywXx OlXg D77 User’s Manual Basic Installation Guxux xyyGywPuXu Puw duy Duy$,6 9HUVLRQ Cancel key Ay The Menu key scrolls the menu Enter keyUp and Down keys scroll and select menu options RuwyScanning device documentation on how to do this Always consult the Network Administrator before makingChanges to the network configuration Turn off the Axis 700 by unplugging the power supplyWhere x.xx is the software version number Power up the Axis 700. Press MenuAfter a few seconds this display will be shown Press Enter to edit the default router address Press Enter to edit the IP addressPress Enter to edit the subnet mask Press Menu once more to display the final instructions JyyByy From the Axis 700 control panelCyyz SuxXd Oxx SWRdAu bu IWRd Host will return ‘Reply from 172.19.2.254...’ or a similar Communication is establishedYour Axis 700. Type arp -a to display the ARP table IbXl u cg69 IP address and verify the communicationEther for Ethernet networks, e.g. arp -s ether spserv Ethernet address Host name Typically performed using the command bootpd -a IcchdWhere Required by your systemHttp//172.19.2.254 GywPuXu OlXg D77 User’s Manual Configuring the Axis Network protocol settingsGywRlXg D77 This brings you to the Axis 700 HomeOlXg D77 User’s Manual Configuring the Axis Click Network Settings Auhd0 TyuOxxy Sy jyGywRlXg D77 OlXg D77 User’s Manual Configuring the Axis T4hd0 From this page you can set the following parametersTu Oxxy =countrycode Configuration parameters are described in The Parameter Last five fields only apply to file destinations.Description, Transfer method and Destination fields are Mandatory for all destination types. For FTP destinations,Table. Click Detailed to view the detailed settings Destination Name is the text that will appearDestination list on the Axis 700 control panel Can make these temporary destinations permanent by clickingMail addresses using the Smtp protocol T4uyMail destinations GywRlXg D77 When the URL is sent to an e-mail destination If z TuWill be stored Click Destination Defaults to change the default values SyyzuInformation Filenamesequencenumber.fileextension, e.g. image001.tif GywRlXg D77 Iy c Most needs. This table lists the predefined profiles Profile Name list to edit an existing profileAxis 700 interface Click New Profile to add a new profile to the listOlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Configuring the Axis GywRlXg D77 OlXg D77 User’s Manual Using the Axis Gywi Xg D77 T4uKyv P Gwu if Axis 700 display shows Send to xxxxxx when it is Optionally, press Menu To change the default settings for Destinations on Perform these instructions from the Axis 700 control panelSetting Several separate pages or stacks of papersYv gyu gyy Canon DR-3020 scanner. a job separation sheet inserted in aOther separation pages will be ignored Sharp AR-seriesLine Administrator might not allow users to add temporary Down or re-startedInterface Enter the name or IP address of your Axis 700 onOlXg D77 User’s Manual Using the Axis This table outlines when to use the predefined profiles Default profile is TextDepending on your scanning device, some profiles may not be Black/white scanning devices, unless they can do gray-scaleMaintained by the Administrator Default paper size is LetterDu g SyxExample Several separate pages Xux CRf uwOwuyuxy OlXg D77 User’s Manual Using the Axis Owy Axis 700 User’s Manual Appendix a Troubleshooting FTPOG h Axis 700 User’s Manual Tml This table lists a summary of error conditions Gu Xxu By Xxwu czzCDB Flatbed only Work. Attached scanner id is displayed in the event log Axis 700 Home Page is displayed. Click Administration Field and press EnterEvent log is displayed Ldap allows resources and services to be selected with ease Accessed with location-independenceAxis 700 User’s Manual Appendix B Ldap System looks likeAxis 700 User’s Manual Dwwu Only want to retrieve entries of the people class, with Could be achieved with the following filterObjectclass=personcn=john Axis 700 User’s Manual Appendix B Ldap Axis 700 User’s Manual OlXg D77 User’s Manual Appendix C The Parameter List Gives a brief description of the parameterAs in the table below DefaultRouter ORG hURL Smtp = Destination name END Compare against the latest software issues from Axis Where you can download the latest versions of the softwareAxis web site on how to join the AxisNews OlXg D77 User’s Manual Appendix D Updating the SoftwareOSG i y OlXg D77 User’s Manual Appendix D Updating the Software OSG i y Client Web browser, and at least one of these protocols File Transfer Protocol FTP serverSimple Mail Transfer Protocol Smtp server Netscape Navigator 3.0 or higherOuu Number is limited by the Eeprom memory. If using Ldap or Software over the network using FTP12V DC 36VA, via external power unit Axis PS-C or 12V DC 13,2VA, via external power unit Axis PS-EOuu OlXg D77 User’s Manual Appendix F Glossary Axis 700 User’s Manual OlXg D77 User’s Manual Appendix F Glossary 100 OlXg D77 User’s Manual Index 101 Http OlXg D77 User’s Manual Index 103 Dhcp Rarp

Related manuals

Manual 6 pages 3.58 Kb