FieldServer FS-8700-132, FCI E3 Series instruction manual

Page 18

FS-8700-132 Gamewell FCI-E3 Driver Manual

Page 18 of 20

 

 

 

 

 

 

 

 

 

 

Message

Description

 

 

 

This message should only be printed if a

 

 

FCI_E3:#17 Err. Loop=%d < 1. Rejected. , drv_bd->loop )

byte in a message has been corrupted. If

 

 

you notice it more than once then take a

 

 

 

 

 

 

log and contact tech support.

 

 

 

If this error is repeated often it is possible

 

 

FCI_E3:#18 Err. Loop Type='%c'(%#x) Not recognized. ,

that a FCI firmware update has made the

 

 

drv_bd->point_identifier[2] , drv_bd->point_identifier[2] )

driver unusable. Take a log and contact

 

 

 

tech support.

 

 

FCI_E3:#19 Err. Relay=%d < 1. Rejected. , drv_bd->relay

This message should only be printed if a

 

 

byte in a message has been corrupted. If

 

 

 

 

 

FCI_E3:#20 Err. Zone=%d < 1. Rejected. , drv_bd->zone"

you notice it more than once then take a

 

 

log and contact tech support.

 

 

 

 

 

FCI_E3:#21 Err. Point Type not recognized

Valid Point Types are listed in section

 

 

FCI_E3:#22 Err. Undefined Point Type"

4.4.25

 

 

FCI_E3:#23 Err. Event Type not recognized

Valid Event Types are listed in section

 

 

FCI_E3:#24 Err. Undefined Event Type

4.4.25

 

 

FCI_E3:#25a Err. Address+Length>99. Length Truncated

The maximum value for a sensor/module

 

 

FCI_E3:#25b Err. Address+Length>99. Length Truncated

is 99. The combination of address and

 

 

length specified produce a number > 995

 

 

FCI_E3:#26 Err. Invalid Module number. Expected 1..99

 

 

 

FCI_E3:#27a Err. Invalid Loop number. Expected 1..10

 

 

 

FCI_E3:#27b Err. Invalid Loop number. Expected 1..10

 

 

 

FCI_E3:#27c Err. Invalid Loop number. Expected 1..10

Correct the configuration file5

 

 

FCI_E3:#28 Err. Invalid Sensor number. Expected 1..99

 

 

 

FCI_E3:#29 Err. Invalid Zone number. Expected 1..255

 

 

 

FCI_E3:#30 Err. Invalid Relay number. Expected 1..255

 

 

 

FCI_E3:#31 Err. Point Type Invalid.

Valid Point Types are listed in Section

 

 

4.4.25

 

 

FCI_E3:#32 Err. No MD Length. Default to 1

The length of each Map Descriptor should

 

 

be specified. Refer to Section 4.4.25

 

 

 

The driver can only listen passively for

 

 

FCI_E3:#33 Err. Driver can’t poll or write.

message from the panel. Map Descriptors

 

 

 

may not be configured as active. 5

 

 

 

An event message is less than 80 bytes

 

 

 

long. If this error is repeated often it is

 

 

FCI_E3:#36 Err. Too Short. Bytes=%d , conn->ux_iptr"

possible that a FCI firmware update has

 

 

 

made the driver unusable. Take a log and

 

 

 

contact tech support.

 

5Correct the configuration file, download to the FieldServer and restart the FieldServer for the changes to take effect.

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com

Image 18
Contents Driver Manual FS-8700-132 Gamewell FCI E3 Series Serial Effective for all systems manufactured after SeptemberTable of Contents Gamewell FCI-E3 Series Serial Driver Description Max Nodes SupportedILI-MB-E3 Board TB6 FCI-E3GND Data Arrays/Descriptors FCIE3 Client Side Node Descriptors Driver Related Map Descriptor Parameters First Alarm UP Stairs N. ENT Manual Station L1M21 003728 01/01/99CRLFDarelay FS-8700-132 Gamewell FCI-E3 Driver Manual FS-8700-132 Gamewell FCI-E3 Driver ManualPage 13 Trouble Destroyed FCIE3Damodu ANY Appendix A.4. Panel Synchronization Appendix A.5.1 Networked PanelsFYI Page Appendix B.1. Driver Stats Exposed FCIE3STATPARSEDNOERRSEXCLDRESET FCIE3STATRCVDMSGSFCIE3STATNOPLACETOSTORENODE