FieldServer FCI E3 Series, FS-8700-132 instruction manual Appendix B. Driver Error Messages, Fyi

FS-8700-132 Gamewell FCI-E3 Driver ManualPage 17 of 20

Appendix B. Driver Error Messages.

Message							Description
FCI_E3:#1 FYI. Use a DA called <%s> to expose							Refer to Appendix B.1
diagnostic info., FCI_E3_STATS_DA )
FCI_E3:#2 FYI. Added Event Desc=<%s> Index=%d							Printed for information only. No action
Categ=%d		,	new_event_desc			,	required if it confirms your expectations.
new_event_desc_index_value , new_event_desc_categ ) ;
FCI_E3:#3 Err. No space. Reject Event Desc=<%s>							There is only space for 60 event types.4
Index=%d		,	new_event_desc			,
new_event_desc_index_value ) ;
FCI_E3:#4	FYI.	Duplicate	Event		Desc=<%s>.	,	The Event type being added already
new_event_desc ) ;							exists. If you are updating the category,
FCI_E3:#5	FYI.	Duplicate	Event		Desc=<%s>.	,	ignore the message. Otherwise correct the
new_event_desc ) ;							configuration file.4
FCI_E3:#6	Err. Event Index=%d. Too big to set bit.,						If the event index is greater than 64 then
							the data cannot be stored as bits - only 64
drv_bd->event_index )							bits are reserved for events.
FCI_E3:#7a Err. DA=%s too short. Rqd=%d, dt-							The MD in question has a length and
>buffer_name , offset );							offset which makes it run past the end of
FCI_E3:#7b Err. DA=%s too short. Rqd=%d, possible_md-							the Data Array. Message 7b is printed
>data->buffer_name , offset );							when data is being stored as bits.4
FCI_E3:#8 FYI. Reset was rcvd and processed! Stamped							Printed for information only. No action
%s %s , drv_bd->time , drv_bd->date )							required.
							A reset was received but the driver could
FCI_E3:#9 Err. Reset was ignored.							not reset any	data.	'Clear_on_Reset'
							possibly set to 'no' on all Map Descriptors?
FCI_E3:#10 FYI. Reset of DA=%s Off=%d Len=%d,							Printed for information only. No action
possible_md->data->buffer_name				,	possible_md-		required.
>bxi_data_buffer_offset , possible_md->data_length );
FCI_E3:#11 Err. Cant reset DA=%s len=%d rqd=%d,
possible_md->data->buffer_name						,	The Map Descriptor in question has a
da_get_length_in_items ( (DAH_TYP) possible_md->data )							length and offset which makes it run past
,	possible_md->data_length+possible_md-						the end of the Data Array.4
>bxi_data_buffer_offset );
FCI_E3:#12a Err. No MD's to store message data.							The Driver could not find a place to store
							data from a message received. If the data
FCI_E3:#12b Err. No MD's to store message data."							is not required then the message may be
							ignored.	Otherwise	update the
FCI_E3:#13 Err. Msg was ignored. MD Required for
							configuration file4.
Storage.
FCI_E3:#13a Err. Diagnostic 1);							Take a log. Try and repeat the event that
FCI_E3:#13b Err. Diagnostic 2);							caused the message to be printed. Then
FCI_E3:#13c Err. Diagnostic 3);							contact tech support.
FCI_E3:#14	Err.	<%s>	file	not	found., md-
>mapdesc_name ) ;							If this error is repeated often it is possible
FCI_E3:#15 Err. Event Type=<%s> Not recognized." ,							that a FCI firmware update has made the
drv_bd->event_desc )							driver unusable. Take a log and contact
FCI_E3:#16 Err. Point Type='%c'(%#x) Not recognized. ,							tech support.
drv_bd->point_identifier[0] , drv_bd->point_identifier[0] ) ;

4Correct the configuration file, download to the FieldServer and restart the FieldServer for the changes to take effect.

FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: support@fieldserver.com