Paradyne 3551 manual Table C-10 TDM/Flex Error Messages Condition Action

Status Indicators and Control Panel Messages

Table C-10

(1 of 3)

TDM/Flex Error Messages

Message	Condition	Action
All Async >Aggr	All ports of the TDM/Flex are configured	You can correct the problem in one of two
	for asynchronous operation and their	ways:
	combined corresponding synchronous	1. Set the Rate(Kbps) of the DSU, DBM,
	rate exceeds the value for the DSU, DBM,
		or ExtBU to a higher value.
	or ExtBU Rate(Kbps) configuration option.
		2. Lower the port speeds of the DSU,
	If all ports are assigned to asynchronous
		DBM, or ExtBU in the PrtSp
	operation, the sum of the corresponding
		configuration submenu.
	synchronous port speeds must be less
	than the value of the DSU, DBM, or
	ExtBU rate.
Async Undspeed	An attempt was made to run an TDM/Flex	Choose a synchronous port and configure
	asynchronous port at underspeed.	it for underspeed via the appropriate path
	A port configured for asynchronous	(DSU or DBM) in the PrtSp configuration
		submenu.
	operation cannot be configured to run
	underspeed.
DBM Aggreg Exceeded	The sum of the TDM/Flex port speeds is	You can correct the problem in one of two
DSU Aggreg Exceeded	greater than the value for the DSU, DBM,	ways:
ExtBU Agg Exceed	or ExtBU Rate(Kbps) configuration option.	1. Set the Rate(Kbps) of the DSU, DBM,
		or ExtBU to a higher value.
		2. Lower the DSU, DBM, or ExtBU port
		speeds via the appropriate path (DSU
		or DBM) in the PrtSp configuration
		sub-menu.
DSD Speeds diff	Not all of the TDM/Flex ports in the	Set all of the ports in the digital-sharing
	digital-sharing group are set to the same	group to the same speed via the
	speed.	appropriate path (DSU or DBM) in the
		PrtSp configuration submenu.
DSD Wrong RTS	One or more TDM/Flex ports in a	Set RTS Cntrl to DTE for all ports in the
	digital-sharing group with DSD port	digital-sharing group via the appropriate
	control have an incorrect RTS Control	paths (Prt1 and Prt2) in the MUX
	setting.	configuration submenu.
	Each port in a digital-sharing group
	configured for contention must have its
	RTS Control configuration option set to
	DTE (RTS Cntrl: DTE).
Ext Time undspd	The TDM/Flex port selected as the source	Correct the problem in one of two ways:
	of external timing (TxClkSource is set to	1. Configure another synchronous port as
	the port specified in the DSU (or ExtBU)
		underspeed via the appropriate path
	and/or DBM configuration submenu) is
		(DSU or DBM) in the PrtSp
	also an underspeed port.
		configuration submenu.
	A port cannot be the source of external
		2. Configure the other port to provide
	timing and also run underspeed.
		external timing.
Incmpt Diag mode	Mixed diagnostic type is not compatible	Select another diagnostic type via the
	with point-to-point operation.	Diagnostic DSU, DBM, or ExtBU option
		set.
Inval lowest Prt	DCE (the first port on TDM/Flex) was	Select 1 as the first port for the
	previously selected as the second port in	digital-sharing group via the MUX Setup
	a digital-sharing group.	path of the MUX submenu.

3550-A2-GB20-20 December 1996 C-11