Equipment Warranty Support | Paradyne 3551 instruction

COMSPHERE 3550 Series Data Service Units

		Table 1-4
	2-Port TDM/Flex Technical Specifications
Specifications		Criteria

APPLICATION
Multiplexing		Provides time division multiplexing of two independent ports.
Digital sharing		Allows consecutive ports to share the same TDM/Flex channel.

PORT SYNCHRONOUS RATES		1.2, 2.4, 4.8, 9.6, 12.0, 14.4, 19.2, 48, 56, and 64 kbps

PORT ASYNCHRONOUS RATES		150, 300, 600, 1200, and 1800 bps plus all primary (DSU) rates.
		Asynchronous rates support +2.3, ±2.5 percent overspeed/
		underspeed compensation.

PORT DTE INTERFACE
3550 DSU (2-port TDM/Flex)		Provides an additional 25-pin D-subminiature connector for a total of two
		EIA-232 or V.35 interfaces.

NMS SUPPORT		TDM/Flex capability is fully supported by Release 4.0 or greater
		COMSPHERE 6700 Series NMS.

Equipment Warranty

and Support

Contact your sales or service representative directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, or training, use one of the following methods:

•Via the Internet: Visit the Paradyne World Wide Web site at http://www.paradyne.com

•Via Telephone: Call our automated call system to receive current information via fax or to speak with a company representative.

ÐWithin the U.S.A., call 1-800-870-2221

ÐInternational, call 727-530-2340

1-8

December 1996

3550-A2-GB20-20

Image 21

Paradyne 3551 manual Equipment Warranty Support, Port TDM/Flex Technical Specifications

Contents

Comsphere 3550 Series Data Service Units Models 3550 Warranty, Sales, and Service Information TrademarksCopyright 1996 Paradyne Corporation. All rights reserved Important Safety Instructions CC DGD D C D CC Interface Data Rate Code Bps Government Requirements Comsphere 3550 Series Data Service Units Table of Contents Glossary Index List of Figures List of Tables Hubbing Device CC IN/DC OUT Jack Pin Assignments How to Use This Guide PrefaceAbout This Guide Reference Documents Related Documents Standard Features About Your DSUOverview 32 DBM Optional Features Upgrades Available Technical SpecificationsPort TDM/Flex CSA Specifications Criteria DSU Heat Dissipation MAX. AT 115 VAC Lads DSU Technical Specifications DOC DBM Technical Specifications Criteria Port TDM/Flex Technical Specifications Equipment Warranty Support Before You Begin Installing the Model 3550 DSU Procedure How to Change Hardware Straps Permissive V.32 DBM transmit output level of ±9 dBm Installing the DSU Where to Place the DSU Power-Up Routine Connecting to the Network Connecting to the Dial or Pstn Network Connecting to the NMS Model 3550 DSU DDS Lads Network Connection Connecting to the DDS or Lads Network Addressing the Unit Lads Connection Distances Data Rate Wire Gauge AWG Kbps Addressing Example Tributary DSU Addressing Installing Cables Connecting the DSU to a DTE Connecting Port Verifying Operation and Testing ConnectionsVerifying Network Addresses Verifying the Network Verifying DBM Operation Verifying TDM/Flex OperationOther Tests Installing the Model 3551 DSU Before You Begin Off Strap State Function Designation Jumper Strap Model 3551 DSU Jumper Straps Comsphere 3000 Series Carrier, Rear View Model 3551 DSU Installation and Circuit Pack Lock V.35 Interconnect Cable Installation Connecting to Dial or Pstn Network Connecting to DDS or Lads Network Verifying Operation and Testing Connections Verifying Network Addresses, the Network, and DBM Operation To Connect the Sdcp to a DSU Other Tests Operating the DSU DCP and Sdcp Operation Model 3550 Diagnostic Control Panel Sdcp and Model 3551 DSU Faceplate Keypad Menu Structure Status BranchHealth and Status Top-Level Menu DTE Status Terminal PowerCircuit Quality Identity Dial Backup Operation Backup BranchConfiguring the Unit for Dial Backup Identity Descriptions Auto Bckup ± Select Enab Understanding Operating Modes Placing a Backup Call Manual BackupManual Dial Backup Termination Manual DDS Restoration Abort Test BranchDevice Test Loopback DTE Loopback Bilateral LoopbackDigital Loopback Remote Digital Loopback End-to-End Test Bit Error Rate Test Selecting Menu Mode Configuration BranchBit Error Rate Test Results Information Displayed Lamp Test Selecting an Application Configuration Configuration Options Reconfiguring a DSU PortReconfiguring a TDM/Flex Port Poll List Displaying the Poll ListChanging the Poll List Q u i r P o l l L i s t Abort Acquiring the Poll List Entering a Telephone Number Directory Phone Directory Entry and Password Characters UseNetwork Address Assigning an Address Transmitter Control Control BranchLEDs External Leads Lead States Symbol Messages BranchReporting External Lead Changes to NMS Security Access Levels Security Functions Available Access LevelFront Panel DCP Security Configuring the Unit Editing Configuration Values Using the DCP to Set Configuration Options Example Using the DCP Saving Configuration Options Ptpc Understanding the Tables Configuration Option Tables DDS DSU Configuration Options Support a Transmit Elastic Store Diagnostic DSU Configuration Options Diagnostic DBM Configuration Options Diagnostic General Configuration Options Diagnostic External DBU Configuration Options DTE operation RXC DBM Configuration Options Disab Select disable if you do not have an extended network DSUs and DBMs If DTR is low DCE External DBU Configuration Options General Configuration Options DTE=RTS Select to ignore the Loopback command Signal is dropped DTE asynchronous data rate Backup Configuration Options TriesTimeOut period expires MUX Setup Configuration Options MUX Port Configuration OptionsDSD 1800 Select the rate of the asynchronous port Configuration option Receiver Carrier Select Messages to the DSU Port Speed DSU Configuration Options Port Speed DBM Configuration Options Port Speed External DBU Configuration Options Port1 DSU 9.6 C Local Remot Msg DSU Menu a Comsphere 3550 Series Data Service Units DSU Menu Local branch Local/Remote Menu Subbranches Overview Instructions Configuration Worksheets B Model 3550 or 3551 DSU Configuration Worksheet 1 Model 3550 or 3551 DSU Configuration Worksheet 2 Full Menu Mode Disabled Port Speed DSU Value Status Indicators Status Indicators and C Control Panel Messages Sdcp Status Indicators DSU Status IndicatorsTable C-1 Label Color Description Format Control Panel MessagesHealth and Status Messages Table C-3 Device Health and Status Messages Condition Table C-3 Device Health and Status Messages Condition Pnnn Tst test,init Message Condition Failnreason Table C-4 Expanded Health and Status Messages Condition Table C-5 Subnetwork Health and Status Messages Condition DTRMUX Command Progress Messages Table C-7 Dial Backup Progress Messages ConditionProgress Messages Table C-8 Command Error Messages Condition Action Error Messages DBM Table C-10 TDM/Flex Error Messages Condition Action Prt2 Table C-10 TDM/Flex Error Messages Condition Action Pin Assignments D Figure D-1. Digital Network Connector Table D-1 Pin Circuit FunctionHubbing Device DCORD/CCISD DCOSD/CCIRDDCOCTS/CCIRTS DCORTS/CCICTS OUT DCOSD/CCIRD GND Comsphere 3550 Series Data Service Units SBB SBA Figure D-4. V.35 Interconnect Cable 3000-F1-510 Cable Circuit Name Pin Number Figure D-5. EIA-232-D Crossover Cable 4951-035F Figure D-6. V.35 Crossover Cable 3211-178F Point-to-Point Applications Application Configurations E Comsphere 3550 Series Data Service Units Multipoint Applications Figure E-2. Multipoint Application Configurations Equipment List = Factory InstallEquipment Comcode Comsphere 3000 Series Carrier, Installation Manual Equipment Part Number Pin-to-Pin EIA-232 Cable straight connection 10 i Ð Active core Glossary CSA DOC LDM RTS TXD Index Index-2 Configuring unit DSD Index-5 MUX Index-7 SDCP, C-2 Index-9