COMSPHERE 3550 Series Data Service Units

Table 5-6

(1 of 4)

DBM Configuration Options

Rate(Kbps): 9.6

 

 

 

 

 

 

 

Next

14.4

12.0

9.6

4.8

2.4

Prev

 

 

DBM Rate. Sets the initial data rate (in kbps) of the DBM for backup calls over the dial circuit.

14.4 to

Ð

Select the data rate for V.32bis modulation. The rate 14.4 is not displayed if you have a 12.0 kbps DBM.

4.8 kbps

 

 

 

 

 

 

 

 

 

2.4

Ð

Select for V .22bis modulation.

 

 

 

 

 

 

 

 

 

 

 

 

 

PrtSp(Kbps):

9.6

 

 

 

 

 

 

 

Next

14.4

12.0

9.6

4.8

2.4

1.2

Disab

Prev

Port Speed (not displayed with a TDM/Flex installed and enabled). Sets the speed of the DTE port interface. The port speed is set to any value less than or equal to the DBM Rate(Kbps) set above. The DBM performs rate adaption if set to less than the DBM port rate.

14.4 to

Ð Select the port speed for the DBM; 14.4 will not appear for a 12.0 kbps DBM.

1.2 kbps

 

 

 

 

 

 

 

Disab

Ð Select disable to set the port speed to 0.

 

 

 

TxClkSource: Int for a control DBM; RXC for a tributary DBM

 

Next

Int

RXC

Ext

Prt1

Prt2

DSU

Prev

Transmit Clock Source. Specifies the transmit timing source for the DBM.

Int

Ð Select internal clock source to take timing from the DBM. This setting is used primarily in point-to-point

 

 

applications.

 

 

 

 

RXC

Ð Select receive clock source to take timing from the remote DBM's clock source.

Ext

Ð

Select external clock source when timing is taken from the external Transmit T iming lead on Port 1 (not

 

 

displayed if a TDM/Flex is installed).

 

 

Prt1 or

Ð Select the port that timing is to be taken from, using the selected port's external Transmit

Prt2

 

Timing lead (displayed if a TDM/Flex is installed and is enabled).

DSU

Ð Select the DSU's clock source when connected to a DDS network and the network is to provide the

 

 

timing. Do not select DSU if the DSU and the DBM operate at different rates.

 

 

 

 

 

 

CarrLossDisc: Yes

 

 

 

 

 

Next

Yes

No

Prev

 

 

 

 

Carrier Loss Disconnect (only displayed when Full Mode is enabled). Controls whether the DBM terminates a call when receive signal carrier is lost, or when the signal is no longer acceptable.

Yes

Ð

Select when you want to terminate the backup call when the carrier is lost.

No

Ð

Never select; for factory testing only. Selecting No will cause an off-hook line condition, which will result in

 

 

excessive telephone charges.

 

 

Auto Retrain:Yes

 

Next

Yes

No

Prev

Automatic Retrain (only displayed when Full Mode is enabled). Controls whether the DBM will start a retrain sequence automatically when received signal quality is no longer acceptable.

Yes

Ð

Select if you want the DBM to retrain automatically.

No

Ð

Select if you do not want the DBM to retrain automatically. However, the DBM will respond to a retrain

 

 

request from a remote modem or DBM.

5-12

December 1996

3550-A2-GB20-20

Page 78
Image 78
Paradyne 3551 manual DBM Configuration Options, Rxc